Maximum speed

A second turntable with a higher maximum speed can carry objects with a size up to 300 mm in diameter and a weight up to 250 kg. This turntable can be fixed both, at the front-side and at the back-side of the main turntable. In this manner the operator can make use of the full length of the radiation fan also in the case of small objects. 

Under what circumstances would the maximum speed be numerically equal to the maximum excursion for a simple hamionic oscillator ... 

How long does it take for each N atom to get from its minimum speed to its maximum speed ... 

What is the maximum speed of the niPogen atoms as they move toward and away from one another ... 

The plough cannot be allowed to reach too close to the cloth and some residual cake remains. Where this is not acceptable, the cake may be removed by a pneumatic system, by vacuum, or by reslurrying. The cycle can be automated and controlled by timers. The maximum speeds of basket centrifuges vary from 800 to 1500 rpm, and basket diameters are in the range from 10 to 1400 mm. A 1200-mm diameter, 750-mm long basket may handle as much as 200 kg of cake in one charge. 

Fig. 2. Improvement over time (a) chip area and minimum feature si2e (b) maximum speed and cost per logic gate.

Speed Devices. Many displacement pumps are connected by variable speed drives. When these pumps are used as a time device on a homogenizer, the setting is fixed, ie, the maximum speed is limited in order to meet the requirements of pasteurization. 

Model no. Rotor dimensions, in Maximum feed size, in Maximum speed, r/min hp Capacity, tons/h... 

Maximum horsepower depends upon maximum speed. 

Class of governor Adjustable speed range Maximum steady-state speed regulation Maximum speed variables, plus or minus Maximum speed rise Trip speed (percent above rated speed)... 

Type of Drive Speed Range Starting Torque Maximum Speed Dynamic Response... 

Cut-oul wind speed is the maximum w ind speed beyond which the prime mover may overspeed above its permissible limits. As the structure and the blades are designed for a particular maximum speed, a wind speed higher than this may exceed their mechanical endurance and become unsafe. At this speed the brakes apply and the machine is disconnected from the grid. The cut-in and cut-out speeds define the wind speed limits within which the turbine will work safely through the generator. Rated wind speed is the speed at which the prime mover rotates at the rated negative slip and generates the rated power. 

Intermediate spinning at half the maximum speed of spinning, i.e. at 8 or 12 pole. 

We saw in Chapter 6 that the speed of a diffusive transformation depends strongly on temperature (see Fig. 6.6). The diffusive f.c.c. b.c.c. transformation in iron shows the same dependence, with a maximum speed at perhaps 700°C (see Fig. 8.1). Now we must be careful not to jump to conclusions about Fig. 8.1. This plots the speed of an individual b.c.c.-f.c.c. interface, measured in metres per second. If we want to know the overall rate of the transformation (the volume transformed per second) then we need to know the area of the b.c.c.-f.c.c. interface as well. 

Select the frame size (hub diameter, d ) using Figure 6-9. At the inlet volume value, a 44 frame is selected with a maximum speed of 3,150 rpm. This frame has a 44-inch hub diameter... 

The speed just calculated is less than the maximum speed of 3150 given for the frame and is therefore acceptable. 

Direct-reading polychromators (Figure 3b) have a number of exit slits and photomultiplier tube detectors, which allows one to view emission from many lines simultaneously. More than 40 elements can be determined in less than one minute. The choice of emission lines in the polychromator must be made before the instrument is purchased. The polychromator can be used to monitor transient signals (if the appropriate electronics and software are available) because unlike slew-scan systems it can be set stably to the peak emission wavelength. Background emission cannot be measured simultaneously at a wavelength close to the line for each element of interest. For maximum speed and flexibility both a direct-reading polychromator and a slew-scan monochromator can be used to view emission from the plasma simultaneously. 

Similar behavior was observed for LNG clouds during both continuous and instantaneous tests, but average flame speeds were lower the maximum speed observed in any of the tests was 10 m/s. Following premixed combustion, the flame burned through the fuel-rich portion of the cloud. This stage of combustion was more evident for continuous spills, where the rate of flame propagation, particularly for LNG spills, was very low. In one of the continuous LNG tests, a wind speed of only 4.5 m/s was sufficient to hold the flame stationary at a point some 65 m from the spill point for almost 1 minute the spill rate was then reduced. 

Vehicle maximum speed is indicated in Figure 1 by the intersections of the power available and power required cuiwes. It is seen to fall from more than 120 mph to 90 mph in going from conditions of Figure la to Figure Ic. In the early days of the automobile, top speed was of greater importance than today. The Panhard Levassor of 1886 was capable of only 12 mph. In about 1900, cars with a top speed of about 40 mph had become available, which may have been adequate for existing roads. When the first concrete road appeared in 1909, the Olds Limited could reach... 

The federal test procedure for new vehicle certification IS limited to a maximum acceleration rate of 3.3 mph/sccond and a maximum speed of 57 mph (and even that speed is for a veiy short duration). Based upon extensive data collected in Baltimore, Spokane, and Atlanta, more than 8.5 percent of all speeds exceeded 57 mph, and more than 88 percent of trips contained acceleration activity exceeding 4 mph/sec-ond. In fact, more than one-third of the trips monitored included an acceleration rate at some point during the trip of more than 7 mpli/second. Similarly, more than 15 percent of the deceleration activity exceeded -3.5 mph/second. Hence, enrichment events are significant in real-world emissions inventories. 

Generally limited to a maximum speed, range may be narrow for some services. 

The maximum speed of a compressor is fixed by mechanical or structural limiting of the peripheral velocity of the impeller wheels. The required velocity is established by the head to be developed. The capacity of the machine at suction conditions is a function of the individual wheel designs and the diameter. ... 

The maximum speed for these machines ranges from 500-4,000 rpm, depending upon bearing design and unit size. For comparison selections refer to Huffr and Patton. ... 

Fixed speed. Advise synchronous speed desired (i.e., 3,600, 1,800, etc.) for AC motors. For DC motors, advise desired basic speed at full, load, and maximum speed by field control. 

---