Polytetrafluoroethylen

Figure X-9 shows plots of cos 6 versus 7l for various series of liquids on Teflon (polytetrafluoroethylene) [78]. Each line extrapolates to zero at a certain 7l value, which Zisman has called the critical surface tension 7 since various series extrapolated to about the same value, he proposed that 7 was a quantity characteristic of a given solid. For Teflon, the representative 7 was taken to be about 18 and was regarded as characteristic of a surface consisting of —CF2 — groups.

Dekker A, Reitsma K, Beugeling T, Bant]es A, Fei]en J and van Aken W G 1991 Adhesion of endothelial-oells and adsorption of serum-proteins on gas plasma-treated polytetrafluoroethylene S/omaferfa/s 12 130-8... 

Tetrafluoroethylene. Emulsion polymerisation of tetrafluoroethylene, catalysed by oxygen, yields polytetrafluoroethylene (Tejlon) as a very tough horn-hke material of high melting point. It possesses excellent electrical insulation properties and a remarkable inertness towards all chemical reagents, including aqua regia. 

A recent innovation in IR sample preparation is the use of disposable sample cards made from thin sheets of either polyethylene (PE) or polytetrafluoroethylene (PTFE). 

Figure 3.16a shows the storage and loss components of the compliance of crystalline polytetrafluoroethylene at 22.6°C. While not identical to the theoretical curve based on a single Voigt element, the general features are readily recognizable. Note that the range of frequencies over which the feature in Fig. 3.16a develops is much narrower than suggested by the scale in Fig. 3.13. This is because the sample under investigation is crystalline. For amorphous polymers, the observed loss peaks are actually broader than predicted by a...

Figure 3.16 Some experimental dynamic components, (a) Storage and loss compliance of crystalline polytetrafluoroethylene measured at different frequencies. [Data from E. R. Fitzgerald, J. Chem. Phys. 27 1 180 (1957).] (b) Storage modulus and loss tangent of poly(methyl acrylate) and poly(methyl methacrylate) measured at different temperatures. (Reprinted with permission from J. Heijboer in D. J. Meier (Ed.), Molecular Basis of Transitions and Relaxations, Gordon and Breach, New York, 1978.)...

Eig. 6. Decomposition of polymers as a function of temperature during heating. A, polymethylene B, polytetrafluoroethylene C, silicone D, phenoHc resin ... 

Dry chlorine has a great affinity for absorbing moisture, and wet chlorine is extremely corrosive, attacking most common materials except HasteUoy C, titanium, and tantalum. These metals are protected from attack by the acids formed by chlorine hydrolysis because of surface oxide films on the metal. Tantalum is the preferred constmction material for service with wet and dry chlorine. Wet chlorine gas is handled under pressure using fiberglass-reinforced plastics. Rubber-lined steel is suitable for wet chlorine gas handling up to 100°C. At low pressures and low temperatures PVC, chlorinated PVC, and reinforced polyester resins are also used. Polytetrafluoroethylene (PTFE), poly(vinyhdene fluoride) (PVDE), and... 

AUoys of ceUulose with up to 50% of synthetic polymers (polyethylene, poly(vinyl chloride), polystyrene, polytetrafluoroethylene) have also been made, but have never found commercial appUcations. In fact, any material that can survive the chemistry of the viscose process and can be obtained in particle sizes of less than 5 p.m can be aUoyed with viscose. 

Polytetrafluoroethylene (PTFE) provides the most satisfactory electrical insulation. Concentric rings of PTFE and PTFE impregnated with calcium fluoride are used for the packing glands which support the anode and cathode posts. Rubber is used as the gasket material to form a seal between the cover... 

Aqueous hydrogen fluoride of greater than 60% maybe handled in steel up to 38°C, provided velocities are kept low (<0.3 m/s) and iron pickup in the process stream is acceptable. Otherwise, mbber or polytetrafluoroethylene (PTFE) linings are used. For all appHcations, PTFE or PTEE-lined materials are suitable up to the maximum use temperature of 200°C. PTEE is also the material of choice for gasketing. AHoy 20 or Monel is typically used for valve and pump appHcations. Materials unacceptable for use in HE include cast iron, type 400 stainless steel, hardened steels, titanium, glass, and siHcate ceramics. 

In some cases particles have been added to electrical systems to improve heat removal, for example with an SF -fluidized particulate bed to be used in transformers (47). This process appears feasible, using polytetrafluoroethylene (PTFE) particles of low dielectric constant. For a successful appHcation, practical problems such as fluidizing narrow gaps must be solved. 

Steric Factors. Initially, most of the coUisions of fluorine molecules with saturated or aromatic hydrocarbons occur at a hydrogen site or at a TT-bond (unsaturated) site. When coUision occurs at the TT-bond, the double bond disappears but the single bond remains because the energy released in initiation (eq. 4) is insufficient to fracture the carbon—carbon single bond. Once carbon—fluorine bonds have begun to form on the carbon skeleton of either an unsaturated or alkane system, the carbon skeleton is somewhat stericaUy protected by the sheath of fluorine atoms. Figure 2, which shows the crowded hehcal arrangement of fluorine around the carbon backbone of polytetrafluoroethylene (PTFE), is an example of an extreme case of steric protection of carbon—carbon bonds (29). 

Fig. 2. The steric protection of the carbon backbone by fluorine of a polytetrafluoroethylene chain. The hehcal configuration with a repeat distance of 1.68...

---