Polytetrafluoroethylene latexes

Herschleb JH (1960) The structure of polytetrafluoroethylene latex paticles. Paper presented at the Electron Microscopy Society of America meeting, Milwaukee (August)... 

HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HMX HNS NTO NTO/HMX NTO/HMX NTO/HMX PETN PETN PETN PETN PETN PETN PETN PETN PETN PETN RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX RDX TATB/HMX Cariflex (thermoplastic elastomer) Hydroxy-terminated polybutadiene (polyurethane) Hydroxy-terminated polyester Kraton (block copolymer of styrene and ethylene-butylene) Nylon (polyamide) Polyester resin-styrene Polyethylene Polyurethane Poly(vinyl) alcohol Poly(vinyl) butyral resin Teflon (polytetrafluoroethylene) Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Cariflex (block copolymer of butadiene-styrene) Cariflex (block copolymer of butadiene-styrene) Estane (polyester polyurethane copolymer) Hytemp (thermoplastic elastomer) Butyl rubber with acetyl tributylcitrate Epoxy resin-diethylenetriamine Kraton (block copolymer of styrene and ethylene-butylene) Latex with bis-(2-ethylhexyl adipate) Nylon (polyamide) Polyester and styrene copolymer Poly(ethyl acrylate) with dibutyl phthalate Silicone rubber Viton (fluoroelastomer) Teflon (polytetrafluoroethylene) Epoxy ether Exon (polychlorotrifluoroethylene/vinylidine chloride) Hydroxy-terminated polybutadiene (polyurethane) Kel-F (polychlorotrifluoroethylene) Nylon (polyamide) Nylon and aluminium Nitro-fluoroalkyl epoxides Polyacrylate and paraffin Polyamide resin Polyisobutylene/Teflon (polytetrafluoroethylene) Polyester Polystyrene Teflon (polytetrafluoroethylene) Kraton (block copolymer of styrene and ethylene-butylene)... 

C is clearly an important quantity for a latex dispersion since it essentially represents the electrolyte concentration at which complete loss of stability occurs. It may be obtained experimentally by a variety of different methods (14,17, 18,19). It should be noted, however, that since coagulation is a kinetic phenomena time enters as a variable and consequently the various methods may yield somewhat different numerical results. This effect is illustrated by results obtained for the coagulation of polytetrafluoroethylene (PTFE) latices with sodium chloride as a function of pH (19). From Figure 4 it can be seen that different results are obtained according to whether the system was examined after 2 h or 24 h. As expected the results indicate that the state of aggregation is more advanced after 24 h and consequently systems at a lower electrolyte concentration have coagulated. Care must therefore be taken when comparing values... 

The formation of coagulum is observed in all types of emulsion polymers (i) synthetic rubber latexes such as butadiene-styrene, acrylonitrile-butadiene, and butadiene-styrene-vinyl pyridine copolymers as well as polybutadiene, polychloroprene, and polyisoprene (ii) coatings latexes such as styrene-butadiene, acrylate ester, vinyl acetate, vinyl chloride, and ethylene copolymers (iii) plastisol resins such as polyvinyl chloride (iv) specialty latexes such as polyethylene, polytetrafluoroethylene, and other fluorinated polymers (v) inverse latexes of polyacrylamide and other water-soluble polymers prepared by inverse emulsion polymerization. There are no major latex classes produced by emulsion polymerization that are completely free of coagulum formation during or after polymerization. 

This book presents coverage of the dynamics, preparation, application and physico-chemical properties of polymer solutions and colloids. It also covers the adsorption characteristics at and the adhesion properties of polymer surfaces. It is written by 23 contemporary experts within their field. Main headings include Structural ordering in polymer solutions Influence of surface Structure on polymer surface behaviour Advances in preparations and appUcations of polymeric microspheres Latex particle heterogeneity origins, detection, and consequences Electrokinetic behaviour of polymer colloids Interaction of polymer latices with other inorganic colloids Thermodynamic and kinetic aspects of bridging flocculation Metal complexation in polymer systems Adsorption of quaternary ammonium compounds art polymer surfaces Adsorption onto polytetrafluoroethylene from aqueous solutions Adsorption from polymer mixtures at the interface with solids Polymer adsorption at oxide surface Preparation of oxide-coated cellulose fibre The evaluation of acid-base properties of polymer surfaces by wettability measurements. Each chapter is well referenced. 

Polytetrafluoroethylene is manufactured and sold in three forms granular, fine powder, and aqueous dispersion each requires a different fabrication technique. Granular resins are manufactured in a wide variety of grades to obtain a different balance between powder flows and end use properties (Fig. 1). Fine powders that are made by coagulating aqueous dispersions are also available in various grades. Differences in fine powder grades correspond to their usefiilness in specific applications and to the ease of fabrication. Aqueous dispersions are sold in latex form and are available in different grades. A variety of formulation techniques are used to tailor these dispersions for specific applications. 

---