Poly polytetrafluoroethylene

Figure 3.16 Some experimental dynamic components, (a) Storage and loss compliance of crystalline polytetrafluoroethylene measured at different frequencies. [Data from E. R. Fitzgerald, J. Chem. Phys. 27 1 180 (1957).] (b) Storage modulus and loss tangent of poly(methyl acrylate) and poly(methyl methacrylate) measured at different temperatures. (Reprinted with permission from J. Heijboer in D. J. Meier (Ed.), Molecular Basis of Transitions and Relaxations, Gordon and Breach, New York, 1978.)...

Dry chlorine has a great affinity for absorbing moisture, and wet chlorine is extremely corrosive, attacking most common materials except HasteUoy C, titanium, and tantalum. These metals are protected from attack by the acids formed by chlorine hydrolysis because of surface oxide films on the metal. Tantalum is the preferred constmction material for service with wet and dry chlorine. Wet chlorine gas is handled under pressure using fiberglass-reinforced plastics. Rubber-lined steel is suitable for wet chlorine gas handling up to 100°C. At low pressures and low temperatures PVC, chlorinated PVC, and reinforced polyester resins are also used. Polytetrafluoroethylene (PTFE), poly(vinyhdene fluoride) (PVDE), and... 

AUoys of ceUulose with up to 50% of synthetic polymers (polyethylene, poly(vinyl chloride), polystyrene, polytetrafluoroethylene) have also been made, but have never found commercial appUcations. In fact, any material that can survive the chemistry of the viscose process and can be obtained in particle sizes of less than 5 p.m can be aUoyed with viscose. 

Surface Protection. The surface properties of fluorosihcones have been studied over a number of years. The CF group has the lowest known intermolecular force of polymer substituents. A study (6) of liquid and solid forms of fluorosihcones has included a comparison to fluorocarbon polymers. The low surface tensions for poly(3,3,3-trifluoropropyl)methylsiloxane and poly(3,3,4,4,5,5,6,6,6-nonafluorohexyl)methylsiloxane both resemble some of the lowest tensions for fluorocarbon polymers, eg, polytetrafluoroethylene. 

Sintering has been used to produce a porous polytetrafluoroethylene (16). Cellulose sponges are the most familiar cellular polymers produced by the leaching process (123). Sodium sulfate crystals are dispersed in the viscose symp and subsequently leached out. Polyethylene (124) or poly(vinyl chloride) can also be produced in cellular form by the leaching process. The artificial leather-tike materials used for shoe uppers are rendered porous by extraction of salts (125) or by designing the polymers in such a way that they precipitate as a gel with many holes (126). 

Electrical Properties. AH polyolefins have low dielectric constants and can be used as insulators in particular, PMP has the lowest dielectric constant among all synthetic resins. As a result, PMP has excellent dielectric properties and alow dielectric loss factor, surpassing those of other polyolefin resins and polytetrafluoroethylene (Teflon). These properties remain nearly constant over a wide temperature range. The dielectric characteristics of poly(vinylcyclohexane) are especially attractive its dielectric loss remains constant between —180 and 160°C, which makes it a prospective high frequency dielectric material of high thermal stabiUty. 

Blends of the polysulfone tesia have been made with ABS, poly(ethylene terephthalate), polytetrafluoroethylene (PTFE), and polycarbonate. These ate sold by Amoco under the Miadel trademark. Additional materials ate compounded with mineral filler, glass, or carbon fiber to improve properties and lower price. 

The melt viscosity of a polymer at a given temperature is a measure of the rate at which chains can move relative to each other. This will be controlled by the ease of rotation about the backbone bonds, i.e. the chain flexibility, and on the degree of entanglement. Because of their low chain flexibility, polymers such as polytetrafluoroethylene, the aromatic polyimides, the aromatic polycarbonates and to a less extent poly(vinyl chloride) and poly(methyl methacrylate) are highly viscous in their melting range as compared with polyethylene and polystyrene. 

There are thus no solvents at room temperature for polyethylene, polypropylene, poly-4 methylpent-l-ene, polyacetals and polytetrafluoroethylene. However, as the temperature is raised and approaches F , the FAS term becomes greater than AH and appropriate solvents become effective. Swelling will, however, occur in the amorphous zones of the polymer in the presence of solvents of similar solubility parameter, even at temperatures well below T. ... 

There is much evidence that weak links are present in the chains of most polymer species. These weak points may be at a terminal position and arise from the specific mechanism of chain termination or may be non-terminal and arise from a momentary aberration in the modus operandi of the polymerisation reaction. Because of these weak points it is found that polyethylene, polytetrafluoroethylene and poly(vinyl chloride), to take just three well-known examples, have a much lower resistance to thermal degradation than low molecular weight analogues. For similar reasons polyacrylonitrile and natural rubber may degrade whilst being dissolved in suitable solvents. 

Poly(ethylene terephtlhalate) Phenol-formaldehyde Polyimide Polyisobutylene Poly(methyl methacrylate), acrylic Poly-4-methylpentene-1 Polyoxymethylene polyformaldehyde, acetal Polypropylene Polyphenylene ether Polyphenylene oxide Poly(phenylene sulphide) Poly(phenylene sulphone) Polystyrene Polysulfone Polytetrafluoroethylene Polyurethane Poly(vinyl acetate) Poly(vinyl alcohol) Poly(vinyl butyral) Poly(vinyl chloride) Poly(vinylidene chloride) Poly(vinylidene fluoride) Poly(vinyl formal) Polyvinylcarbazole Styrene Acrylonitrile Styrene butadiene rubber Styrene-butadiene-styrene Urea-formaldehyde Unsaturated polyester... 

Hence at room temperature there are no solvents for polyethylene, polypropylene, poly-4-methyl-pentene-l, polyacetal or polytetrafluoroethylene, but at temperatures of about 30°C below their melting point solvents of... 

Some authors have suggested the use of fluorene polymers for this kind of chromatography. Fluorinated polymers have attracted attention due to their unique adsorption properties. Polytetrafluoroethylene (PTFE) is antiadhesive, thus adsorption of hydrophobic as well as hydrophilic molecules is low. Such adsorbents possess extremely low adsorption activity and nonspecific sorption towards many compounds [109 111]. Fluorene polymers as sorbents were first suggested by Hjerten [112] in 1978 and were tested by desalting and concentration of tRN A [113]. Recently Williams et al. [114] presented a new fluorocarbon sorbent (Poly F Column, Du Pont, USA) for reversed-phase HPLC of peptides and proteins. The sorbent has 20 pm in diameter particles (pore size 30 nm, specific surface area 5 m2/g) and withstands pressure of eluent up to 135 bar. There is no limitation of pH range, however, low specific area and capacity (1.1 mg tRNA/g) and relatively low limits of working pressure do not allow the use of this sorbent for preparative chromatography. 

Ethylene vinyl acetate has also found major applications in drug delivery. These copolymers used in drug release normally contain 30-50 wt% of vinyl acetate. They have been commercialized by the Alza Corporation for the delivery of pilocarpine over a one-week period (Ocusert) and the delivery of progesterone for over one year in the form of an intrauterine device (Progestasert). Ethylene vinyl acetate has also been evaluated for the release of macromolecules such as proteins. The release of proteins form these polymers is by a porous diffusion and the pore structure can be used to control the rate of release (3). Similar nonbiodegradable polymers such as the polyurethanes, polyethylenes, polytetrafluoroethylene and poly(methyl methacrylate) have also been used to deliver a variety of different pharmaceutical agents usually as implants or removal devices. 

Crystalline polymers characterized by disordered conformations of the chains are, for instance, polytetrafluoroethylene (PTFE), /ra .s-1,4-poly (1,3-butadiene), and cis-1,4-poly(isoprcnc). 

Polytetrafluoroethylene ionomers, properties of, 14 475 76 Poly(tetrafluoroethylene-co-hexafluoropropylene) films, 23 720... 

Oxygen Polytetrafluoroethylene, Stainless steel, 4831 Poly(tetrafluoroethylene) Oxygen, 0629... 

Xing, D. M., Yi, B. L., Liu, F. Q., Fu, Y. Z. and Zhang, H. M. 2005. Characterization of sulfonated poly (ether ether ketone)/polytetrafluoroethylene composite membranes for fuel cell applications. Fuel Cells 5 406M11. 

Polystyrene Polytetrafluoroethylene Poly(vinyl butyral) Poly(vinyl chloride)... 

Darvic, Elvic, Geon, Koroseal, Marvinol, Mipolam, Opalon, Pliofex, Rucon, Solvic, Trulon, Velon, Vinoflex, Vygen, and Vyram are all trade names for poly(vinyl chloride) manufactured by different companies. Some polymers are better known by their trade name than their generic name. For instance, polytetrafluoroethylene is better known as Teflon, the trade name held by DuPont. 

---