Poly heat resistance

Poly(methyl methacrylate) Cast sheet Impact- modified Heat- resistant ... 

Nitrile mbber finds broad application in industry because of its excellent resistance to oil and chemicals, its good flexibility at low temperatures, high abrasion and heat resistance (up to 120°C), and good mechanical properties. Nitrile mbber consists of butadiene—acrylonitrile copolymers with an acrylonitrile content ranging from 15 to 45% (see Elastomers, SYNTHETIC, NITRILE RUBBER). In addition to the traditional applications of nitrile mbber for hoses, gaskets, seals, and oil well equipment, new applications have emerged with the development of nitrile mbber blends with poly(vinyl chloride) (PVC). These blends combine the chemical resistance and low temperature flexibility characteristics of nitrile mbber with the stability and ozone resistance of PVC. This has greatly expanded the use of nitrile mbber in outdoor applications for hoses, belts, and cable jackets, where ozone resistance is necessary. 

In addition to carbon and glass fibers ia composites, aramid and polyimide fibers are also used ia conjunction with epoxy resias. Safety requirements by the U.S. Federal Aeronautics Administration (FAA) have led to the development of flame- and heat-resistant seals and stmctural components ia civiUan aircraft cabias. Wool blend fabrics containing aramids, poly(phenylene sulfide), EDF, and other inherently flame-resistant fibers and fabrics containing only these highly heat- and flame-resistant fibers are the types most frequently used ia these appHcations. 

Heat resistance is an important characteristic of the bond. The strength of typical abrasive stmctures is tested at RT and at 300°C. Flexural strengths are between 24.1 and 34.4 MPa (3500—5000 psi). An unmodified phenoHc resin bond loses about one-third of its room temperature strength at 298°C. Novolak phenoHc resins are used almost exclusively because these offer heat resistance and because the moisture given off during the cure of resole resins results in undesirable porosity. Some novolaks modified with epoxy or poly(vinyl butyral) resin are used for softer grinding action. 

Automotive appHcations account for about 116,000 t of woddwide consumption aimuaHy, with appHcations for various components including headlamp assembHes, interior instmment panels, bumpers, etc. Many automotive appHcations use blends of polycarbonate with acrylonitrile—butadiene—styrene (ABS) or with poly(butylene terephthalate) (PBT) (see Acrylonitrile polymers). Both large and smaH appHances also account for large markets for polycarbonate. Consumption is about 54,000 t aimuaHy. Polycarbonate is attractive to use in light appHances, including houseware items and power tools, because of its heat resistance and good electrical properties, combined with superior impact resistance. 

Small amounts of TAIC together with DAP have been used to cure unsaturated polyesters in glass-reinforced thermo sets (131). It has been used with polyfunctional methacrylate esters in anaerobic adhesives (132). TAIC and vinyl acetate are copolymerized in aqueous suspension, and vinyl alcohol copolymer gels are made from the products (133). Electron cure of poly(ethylene terephthalate) moldings containing TAIC improves heat resistance and transparency (134). 

Vinyl Acetate—Ethylene Copolymers. In these random copolymers, the ratio of ethylene to vinyl acetate (EVA) is varied from 30—60%. As the vinyl acetate content increases, the oil and heat resistance increases. With higher ethylene content the physical strength, tensile, and tear increases. The polymers are cured with peroxide. The main properties of these elastomers include heat resistance, moderate oil and solvent resistance, low compression set, good weather resistance, high damping, exceUent o2one resistance, and they can be easily colored (see Vinyl polymers, poly(VINYL acetate)). 

Poly(ethyl methacrylate) (PEMA) yields truly compatible blends with poly(vinyl acetate) up to 20% PEMA concentration (133). Synergistic improvement in material properties was observed. Poly(ethylene oxide) forms compatible homogeneous blends with poly(vinyl acetate) (134). The T of the blends and the crystaUizabiUty of the PEO depend on the composition. The miscibility window of poly(vinyl acetate) and its copolymers with alkyl acrylates can be broadened through the incorporation of acryUc acid as a third component (135). A description of compatible and incompatible blends of poly(vinyl acetate) and other copolymers has been compiled (136). Blends of poly(vinyl acetate) copolymers with urethanes can provide improved heat resistance to the product providing reduced creep rates in adhesives used for vinyl laminating (137). 

The acetone supply is strongly influenced by the production of phenol, and so the small difference between total demand and the acetone suppHed by the cumene oxidation process is made up from other sources. The largest use for acetone is in solvents although increasing amounts ate used to make bisphenol A [80-05-7] and methyl methacrylate [80-62-6]. a-Methylstyrene [98-83-9] is produced in controlled quantities from the cleavage of cumene hydroperoxide, or it can be made directly by the dehydrogenation of cumene. About 2% of the cumene produced in 1987 went to a-methylstyrene manufacture for use in poly (a-methylstyrene) and as an ingredient that imparts heat-resistant quaUties to polystyrene plastics. 

Mihtary interest in the development of fuel and thermal resistant elastomers for low temperature service created a need for fluorinated elastomers. In the early 1950s, the M. W. Kellogg Co. in a joint project with the U.S. Army Quartermaster Corps, and 3M in a joint project with the U.S. Air Force, developed two commercial fluorocarbon elastomers. The copolymers of vinyUdene fluoride, CF2=CH2, and chlorotrifluoroethylene, CF2=CFC1, became available from Kellogg in 1955 under the trademark of Kel-F (1-3) (see Fluorine compounds, ORGANic-POLYcm.OROTRiFLUOROETHYLENE Poly(vinylidene) fluoride). In 1956, 3M introduced a polymer based on poly(l,l-dihydroperfluorobutyl acrylate) trademarked 3M Brand Fluorombber 1F4 (4). The poor balance of acid, steam, and heat resistance of the latter elastomer limited its commercial use. 

Most polyesters (qv) are based on phthalates. They are referred to as aromatic-aHphatic or aromatic according to the copolymerized diol. Thus poly(ethylene terephthalate) [25038-59-9] (PET), poly(butyelene terephthalate) [24968-12-5] (PBT), and related polymers are termed aromatic-aHphatic polyester resins, whereas poly(bisphenol A phthalate)s are called aromatic polyester resins or polyarylates PET and PBT resins are the largest volume aromatic-aHphatic products. Other aromatic-aHphatic polyesters (65) include Eastman Kodak s Kodar resin, which is a PET resin modified with isophthalate and dimethylolcyclohexane. Polyarylate resins are lower volume specialty resins for high temperature (HDT) end uses (see HeaT-RESISTANT POLYAffiRS). 

In addition to poly(methyl methacrylate) plastics and polyacrylonitrile fibres, acrylic polymers find widespread use. First introduced in 1946, acrylic rubbers have become established as important special purpose rubbers with a useful combination of oil and heat resistance. Acrylic paints have become widely accepted particularly in the car industry whilst very interesting reactive adhesives, including the well-known super-glues are also made from acrylic polymers. 

Other developments in recent years have been the appearance of tough and heat-resistant materials closely related to poly(methyl methacrylate) and to interesting cross-linked polymers. Amongst these are the so-called hydrophilic polymers used in the making of soft contact lenses. 

Mention may also be made here of a number of polyfunctional compounds such as allyl methacrylate and glycol dimethacrylates which have been used to produce a cross-linked sheet of enhanced heat resistance compared with conventional poly(methyl methacrylate). Some manufacturers supply the sheet in an incompletely cross-linked state which allows a limited amount of forming after which the sheet may be further heated to complete the cure. 

A poly(tribromostyrene) with the bromine atoms attached to the benzene ring is marketed by the Ferro corporation as F yro-Chek 68 PB as a heat-resisting fire retardant used in conjunction with antimony oxide. The polymer has an exceptionally high specific gravity, reputedly of 2.8, and a softening point of 220°C. 

The use of ABS has in recent years met considerable competition on two fronts, particularly in automotive applications. For lower cost applications, where demands of finish and heat resistance are not too severe, blends of polypropylene and ethylene-propylene rubbers have found application (see Chapters 11 and 31). On the other hand, where enhanced heat resistance and surface hardness are required in conjunction with excellent impact properties, polycarbonate-ABS alloys (see Section 20.8) have found many applications. These materials have also replaced ABS in a number of electrical fittings and housings for business and domestic applications. Where improved heat distortion temperature and good electrical insulation properties (including tracking resistance) are important, then ABS may be replaced by poly(butylene terephthalate). 

A measure of the heat resistance can be obtained by the weight loss at various temperatures. Table 18.12 gives details of the weight loss of three poly-pyromellitimides after various heating times at 325°C. 

Poly-p-phenylene has been prepared in the laboratory by a variety of methods, including the condensation of p-dichlorobenzene using the Wurtz-Fittig reaction. Although the polymer has a good heat resistance, with decomposition... 

Polymers with very good heat resistance (both in terms of deformation and of heat aging resistance) but which may be processed by conventional techniques, e.g. polysulphones and poly(phenylene oxides). 

The use of PBT as an engineering material is more a consequence of a balance of good properties rather than of a few outstanding ones. It does not possess the toughness of polycarbonate, the abrasion resistance of an aliphatic polyamide, the heat resistance of a polysulphone, polyketone or poly(phenylene sulphide) or... 

With a somewhat lower level of heat resistance but with many properties that make them of interest as engineering materials alongside the polycarbonates, polysulphones, poly(phenylene sulphides) and polyketones are the so-called polyarylates which are defined as polyester from bis-phenols and dicarboxylic acids. 

Of a somewhat lower level of heat resistance is poly(ethyleneoxy benzoate), which has the structure ... 

In Chapters 3 and 11 reference was made to thermoplastic elastomers of the triblock type. The most well known consist of a block of butadiene units joined at each end to a block of styrene units. At room temperature the styrene blocks congregate into glassy domains which act effectively to link the butadiene segments into a rubbery network. Above the Tg of the polystyrene these domains disappear and the polymer begins to flow like a thermoplastic. Because of the relatively low Tg of the short polystyrene blocks such rubbers have very limited heat resistance. Whilst in principle it may be possible to use end-blocks with a higher Tg an alternative approach is to use a block copolymer in which one of the blocks is capable of crystallisation and with a well above room temperature. Using what may be considered to be an extension of the chemical technology of poly(ethylene terephthalate) this approach has led to the availability of thermoplastic polyester elastomers (Hytrel—Du Pont Amitel—Akzo). 

Compared with the phenolics and polyesters the resins have better heat resistance, better chemical resistance, particularly to alkalis, greater hardness and better water resistance. In these respects they are similar to, and often slightly superior to, the epoxide resins. Unlike the epoxides they have a poor adhesion to wood and metal, this being somewhat improved by incorporating plasticisers such as poly(vinyl acetate) and poly(vinyl formal) but with a consequent reduction in chemical resistance. The cured resins are black in colour. 

Substantial improvements in the heat-resisting capability of silicone rubbers were achieved with the appearance of the poly(carborane siloxanes). First described in 1966, they were introduced commercially by the Olin Corporation in 1971 as Dexsil. The polymers have the essential structure... 

The chemical name for such materials is poly(bisbenzimid-azobenzophenan-throlines) but they are better known as BBB materials. Such polymers have a Tg in excess of 450°C and show only a low weight loss after aging in air for several hundred hours at 370°C. Measurements using thermal gravimetric analysis indicate a good stability to over 600°C. The main interest in these materials is in the field of heat-resistant films and fibres. 

Resistance to weathering. Zinc oxide and magnesium oxide stabilize poly-chloroprene against dehydrochlorination. Further, zinc oxide helps vulcanize the rubber, and magnesium oxide reacts with /-butyl phenolic resin to produce a resinate which improves heat resistance of solvent-borne polychloroprene adhesives. 

In amorphous poly-a-olefins (APAO), the main monomer is propylene. Compared to EVA, it provides better heat resistance. APAO shows good adhesion properties to nonpolar surfaces, good flexibility and high resistance to temperature and moisture. 

Poly(hydroxyphenyl maleimide)-b-PBA was added to thermosetting phenol resin to improve heat resistance [63]. PVC blended with poly(vinyl copolymer having cyclohexyl maleimide group)-b-PVC showed improved heat resistance and tensile strength with thermal stability during processing [64]. 

Poly-2,6-dimethyl phenylene oxide (PPO) and certain related materials are similar to the nylons but have superior heat resistance. These polymers are somewhat liable to stress-cracking problems. 

Siloxane containing polyester, poly(alkylene oxide) and polystyrene type copolymers have been used to improve the heat resistance, lubricity and flow properties of epoxy resin powder coatings 43). Thermally stable polyester-polysiloxane segmented copolymers have been shown to improve the flow, antifriction properties and scratch resistance of acrylic based auto repair lacquers 408). Organohydroxy-terminated siloxanes are also effective internal mold release agents in polyurethane reaction injection molding processes 409). 

One of the earliest and most popular systems investigated are the highly heat-resistant poly(w-carborane-siloxane)s. A review of the general literature on the methods used in the synthesis of these materials is reported in the following sections. 

---