Platinate,

The carbon is often replaced by a catalyst such as platinized or nickelized carbon or a mixture of carbon, platinum and nickel. 

A few illustrative examples are the following. Photohydrogenation of acetylene and ethylene occurs on irradiation of Ti02 exposed to the gases, but only if TiOH surface groups are present as a source of hydrogen [319]. The pho-toinduced conversion of CO2 to CH4 in the presence of Ru and Os colloids has been reported [320]. Platinized Ti02 powder shows, in the presence of water, photochemical oxidation of hydrocarbons [321,322]. Some of the postulated reactions are ... 

Again with platinized Ti02, ultraviolet irradiation can lead to oxidation of aqueous CN [323] and to the water-gas shift reaction, CO + H2O = H2 + CO2 [324]. Some mechanistic aspects of the photooxidation of water (to O2) at the Ti02-aqueous interface are discussed by Bocarsly et al. [325]. 

Some early observations on the catalytic oxidation of SO2 to SO3 on platinized asbestos catalysts led to the following observations (1) the rate was proportional to the SO2 pressure and was inversely proportional to the SO3 pressure (2) the apparent activation energy was 30 kcal/mol (3) the heats of adsorption for SO2, SO3, and O2 were 20, 25, and 30 kcal/mol, respectively. By using appropriate Langmuir equations, show that a possible explanation of the rate data is that there are two kinds of surfaces present, 5 and S2, and that the rate-determining step is... 

Molecular Weight of a Base by Analysis of its Chloro-platinate. 

When platinum is dissolved in aqua regia it is first converted to platinic chloride, PtCl, and the latter at once unites with the excess of hydrochloric acid to give the stable soluble dibasic chloroplatinic acid, HjPtCle.f... 

Method- 3. From platinum metal or platinum residues. Dissolve the platinum metal or platinum residues in aqua regia, evaporate just to dryness several times with concentrated hydrochloric acid, dissolve the final residue in a httle water and precipitate as ammonium chloro-platinate with excess of saturated ammonium chloride solution. Filter and dry the precipitate at 100°. Then proceed according to Method 1. 

It has been stated that the activity of the catalyst in low pressure hydrogenations is enhanced by the addition of small quantities of platinic chloride. 

DSA, lead, platinized titanium platinized titanium or niobium... 

Platinacyclopent-2-ene-4,5-diones synthesis, 1, 669 Platinates, tetracyano-charge density waves in, 1, 352 Platinum... 

Phenylcyclopropene (5). 3 (118 g 0 8 mol), powdered KOH (30 g, 0 S3 mol) and platinize asbestos (2 5 g) were heated slowly and the heat was shut off at the rirsi sign of reaction Afler the exolhemiic reaction the temperature was again raised and the product was distilled Both the distillate end the residue were steam distiled, the distitlate was extracted with Et20... 

In such cases basket anodes are frequently used. These have a relatively large surface and work at a low driving voltage due to their special construction. A cylinder of platinized titanium-expanded metal serves as the basket to which a titanium rod is welded. This serves as the current lead and carrier, and ends in a plastic foot that contains the cable lead and at the same time serves as the mounting plate. The expanded metal anode exhibits a very uniform anode current density distribution, even at large dimensions, in contrast to the plate anode. The reason is the many comers and edges of the metal that make the point effect only evident at the outer edges of the anode. 

A current with ripples can lead to a high consumption rate for platinized titanium anodes and their premature failure. The residual ripple should be limited to 5% (see Section 7.2.2) [7],... 

Galvanic or impressed current anodes are used to protect these components. The anode material is determined by the electrolyte zinc and aluminum for seawater, magnesium for freshwater circuits. Platinized titanium is used for the anode material in impressed current protection. Potential-regulating systems working independently of each other should be used for the inlet and outlet feeds of heat exchangers on account of the different temperature behavior. The protection current densities depend on the material and the medium. 

The internal cathodic protection of pipes is only economic for pipes with a nominal width greater than DIN 400 due to the limit on range. Internal protection can be achieved in individual cases by inserting local platinized titanium wire anodes (see Section 7.2.2). 

Partially platinized titanium impressed current anodes were chosen because contamination of the feed water by anodic decomposition products had to be avoided. Four pure zinc reference electrodes were installed in the tank to control and regulate the potential. The supports for the anodes were of polypropylene, which can operate for short periods up to 100°C, in contrast to the usual PVC supports used in cold water. 

Figure 21-1 shows the object to be protected and the arrangement of impressed current anodes and reference electrodes. A central anode and two ring anodes of platinized titanium wire 3 mm in diameter provided with additional copper wire conductors are installed here. It is worth noting that the central anode is suspended from a float, whereas the ring anode is mounted on plastic supports. The zinc reference electrodes are also on floats near the inner side of the bell, while the 17 reference electrodes are mounted on plastic rods on the bottom of the cup and in the ring... 

Materials that are corrosion resistant to the expected cathodic polarization qualify as impressed current cathodes. Austenitic CrNi steels are used with strong acids. The oleum (i.e., fuming sulfuric acid) and concentrated sulfuric acid tanks used in sulfonating alkanes and in the neutralization of sulfonic acids are anodi-cally protected using platinized brass as cathodes [15]. Lead cathodes are used to protect titanium heat exchangers in rayon spinning baths [16]. 

Seheuing and Winterhalder treated 2 6-distr3rrylpyridine tetra-bromide with potassium hydroxide in alcohol, so producing 2 6-di-)3-phenylacetylenylpyridine (XI) which by the action of 50 per cent, sulphuric acid was converted into 2 6-diphenacylpyridine (XII), and this, on hydrogenation in presence of platinic oxide, barium sulphate and methyl alcohol, was reduced to 2 6-di-(6-hydroxy-(6-phenylethylpyridine, and the hydrochloride of this, on similar catalytic hydrogenation, yielded worlobelanidine (XIII). This can be methylated to lobelanidine, from which in turn dMobeline and lobelanine can be obtained. 

Nicotine may be detected by the colourless, crystalline mercurichloride obtained when an aqueous solution is added to a solution of mercuric chloride, by the black precipitate formed under similar conditions with potassium platinic iodide and the characteristic crystalline periodide, BI2. HI, m.p. 123°, produced on admixture, under specified conditions, 2 of ethereal solutions of nicotine and iodine (cf Anabasine, p. 43). A polarographic study of nicotine has been made by Kirkpatrick. ... 

---