1.2- Shift reactions

The Fischer-Tropsch reaction is essentially that of Eq. XVIII-54 and is of great importance partly by itself and also as part of a coupled set of processes whereby steam or oxygen plus coal or coke is transformed into methane, olefins, alcohols, and gasolines. The first step is to produce a mixture of CO and H2 (called water-gas or synthesis gas ) by the high-temperature treatment of coal or coke with steam. The water-gas shift reaction CO + H2O = CO2 + H2 is then used to adjust the CO/H2 ratio for the feed to the Fischer-Tropsch or synthesis reactor. This last process was disclosed in 1913 and was extensively developed around 1925 by Fischer and Tropsch [268]. 

Again with platinized Ti02, ultraviolet irradiation can lead to oxidation of aqueous CN [323] and to the water-gas shift reaction, CO + H2O = H2 + CO2 [324]. Some mechanistic aspects of the photooxidation of water (to O2) at the Ti02-aqueous interface are discussed by Bocarsly et al. [325]. 

Methanol (qv) is one of the 10 largest volume organic chemicals produced in the wodd, with over 18 x 10 t of production in 1990. The reactions for the synthesis of methanol from CO, CO2, and H2 are shown below. The water gas shift reaction also is important in methanol synthesis. 

Another hydrogenation process utilizes internally generated hydrogen for hydroconversion in a single-stage, noncatalytic, fluidized-bed reactor (41). Biomass is converted in the reactor, which is operated at about 2.1 kPa, 800°C, and residence times of a few minutes with steam-oxygen injection. About 95% carbon conversion is anticipated to produce a medium heat value (MHV) gas which is subjected to the shift reaction, scmbbing, and methanation to form SNG. The cold gas thermal efficiencies are estimated to be about 60%. 

Study of the mechanism of this complex reduction-Hquefaction suggests that part of the mechanism involves formate production from carbonate, dehydration of the vicinal hydroxyl groups in the ceUulosic feed to carbonyl compounds via enols, reduction of the carbonyl group to an alcohol by formate and water, and regeneration of formate (46). In view of the complex nature of the reactants and products, it is likely that a complete understanding of all of the chemical reactions that occur will not be developed. However, the Hquefaction mechanism probably involves catalytic hydrogenation because carbon monoxide would be expected to form at least some hydrogen by the water-gas shift reaction. 

The mixture of carbon monoxide and hydrogen is enriched with hydrogen from the water gas catalytic (Bosch) process, ie, water gas shift reaction, and passed over a cobalt—thoria catalyst to form straight-chain, ie, linear, paraffins, olefins, and alcohols in what is known as the Fisher-Tropsch synthesis. 

Prior to methanation, the gas product from the gasifier must be thoroughly purified, especially from sulfur compounds the precursors of which are widespread throughout coal (23) (see Sulfurremoval and recovery). Moreover, the composition of the gas must be adjusted, if required, to contain three parts hydrogen to one part carbon monoxide to fit the stoichiometry of methane production. This is accompHshed by appHcation of a catalytic water gas shift reaction. 

In the presence of catalysts, the CO reacts with steam through the shift reaction to produce additional hydrogen and CO2 as represented by... 

Synthesis Gas Chemicals. Hydrocarbons are used to generate synthesis gas, a mixture of carbon monoxide and hydrogen, for conversion to other chemicals. The primary chemical made from synthesis gas is methanol, though acetic acid and acetic anhydride are also made by this route. Carbon monoxide (qv) is produced by partial oxidation of hydrocarbons or by the catalytic steam reforming of natural gas. About 96% of synthesis gas is made by steam reforming, followed by the water gas shift reaction to give the desired H2 /CO ratio. 

Reactions of Synthesis Gas. The main hydrogen manufacturing processes produce synthesis gas, a mixture of H2 and CO. Synthesis gas can have a variety of H2-to-CO ratios, and the water gas shift reaction is used to reduce the CO level and produce additional hydrogen, or to adjust the H2 to-CO ratio to one more beneficial to subsequent processing (69) ... 

In the next step, the CO is converted to CO2 and hydrogen by the water gas shift reaction step ... 

This reaction is first conducted on a chromium-promoted iron oxide catalyst in the high temperature shift (HTS) reactor at about 370°C at the inlet. This catalyst is usually in the form of 6 x 6-mm or 9.5 x 9.5-mm tablets, SV about 4000 h . Converted gases are cooled outside of the HTS by producing steam or heating boiler feed water and are sent to the low temperature shift (LTS) converter at about 200—215°C to complete the water gas shift reaction. The LTS catalyst is a copper—zinc oxide catalyst supported on alumina. CO content of the effluent gas is usually 0.1—0.25% on a dry gas basis and has a 14°C approach to equihbrium, ie, an equihbrium temperature 14°C higher than actual, and SV about 4000 h . Operating at as low a temperature as possible is advantageous because of the more favorable equihbrium constants. The product gas from this section contains about 77% H2, 18% CO2, 0.30% CO, and 4.7% CH. ... 

This reaction is commonly known as the CO or water gas shift reaction. The conversion of CO by this reaction is slightly exothermic and favored by lower temperatures. The lower practical operating temperature range for this reaction is between 180 and 200°C (8). 

Subtracting reaction 2 from reaction 1 gives the familiar water gas shift reaction (eq. 3). 

These reactions show that the synthesis gas stoichiometry is dependent on both the nature of the feedstock as well as the generation process. Reactions 4 and 5, together with the water gas shift reaction 3, serve to independently determine the equiUbrium composition of the synthesis gas. 

Synthesis gas, a mixture of CO and o known as syngas, is produced for the oxo process by partial oxidation (eq. 2) or steam reforming (eq. 3) of a carbonaceous feedstock, typically methane or naphtha. The ratio of CO to may be adjusted by cofeeding carbon dioxide (qv), CO2, as illustrated in equation 4, the water gas shift reaction. 

The overall process for producing a 1 1 CO to ratio by partial methane oxidation and the water gas shift reaction is represented by equation 5. 

Synthesis gas preparation consists of three steps ( /) feedstock conversion, (2) carbon monoxide conversion, and (2) gas purification. Table 4 gives the main processes for each of the feedstocks (qv) used. In each case, except for water electrolysis, concommitant to the reactions shown, the water-gas shift reaction occurs. 

Shift Conversion. Carbon oxides deactivate the ammonia synthesis catalyst and must be removed prior to the synthesis loop. The exothermic water-gas shift reaction (eq. 23) provides a convenient mechanism to maximize hydrogen production while converting CO to the more easily removable CO2. A two-stage adiabatic reactor sequence is normally employed to maximize this conversion. The bulk of the CO is shifted to CO2 in a high... 

HTS catalyst consists mainly of magnetite crystals stabilized using chromium oxide. Phosphoms, arsenic, and sulfur are poisons to the catalyst. Low reformer steam to carbon ratios give rise to conditions favoring the formation of iron carbides which catalyze the synthesis of hydrocarbons by the Fisher-Tropsch reaction. Modified iron and iron-free HTS catalysts have been developed to avoid these problems (49,50) and allow operation at steam to carbon ratios as low as 2.7. Kinetic and equiUbrium data for the water gas shift reaction are available in reference 51. 

Tubular Fixed-Bed Reactors. Bundles of downflow reactor tubes filled with catalyst and surrounded by heat-transfer media are tubular fixed-bed reactors. Such reactors are used most notably in steam reforming and phthaUc anhydride manufacture. Steam reforming is the reaction of light hydrocarbons, preferably natural gas or naphthas, with steam over a nickel-supported catalyst to form synthesis gas, which is primarily and CO with some CO2 and CH. Additional conversion to the primary products can be obtained by iron oxide-catalyzed water gas shift reactions, but these are carried out ia large-diameter, fixed-bed reactors rather than ia small-diameter tubes (65). The physical arrangement of a multitubular steam reformer ia a box-shaped furnace has been described (1). 

This is the reverse of the water-gas shift reaction in the production of hydrogen and ammonia (qv). Carbon dioxide may also be reduced catalyticaHy with various hydrocarbons and with carbon itself at elevated temperatures. The latter reaction occurs in almost all cases of combustion of carbonaceous fuels and is generally employed as a method of producing carbon monoxide. 

Conversion to Hydrogen (Water Gas Shift Reaction). Carbon monoxide reacts with water over a catalyst to produce hydrogen and carbon monoxide (25). This reaction is used to prepare high purity hydrogen or synthesis gas with a higher hydrogen-to-carbon monoxide ratio than the feed (eq. 3). 

---