Palladium® chloride

The palladium - barium sulphate catalyst Is prepared by treating a suspension of20g. of barium sulphate (which has been precipitated in hot solution) in 400 ml. of hot water with a solution of I - 7 g. of palladium chloride (equivalent to I - 0 g. of palladium) in 50 ml. of water and with I - 5 ml. of 40 per cent, formaldehyde solution. The mixture is rendered faintly alkaline to litmus by the addition of sodium hydroxide solution and then boiled for a short time. When the supernatant liquid is clear, the grey precipitate is filtered oS, and wa.shed with hot water until the... 

The palladium may be recovered by heating the spent catalyst to redness in order to remove organic impurities this treatment may reduce some of the barium sulphate to barium sulphide, which acts as a catalytic poison. The palladium is then dissolved out with aqua regia and the solution evaporated the residue is dissolved in hot water and hydrochloric acid to form palladium chloride. 

Preparation of palladium - calcium carbonate catalyst. Prepare 60 g. of precipitated calcium carbonate by mixing hot solutions of the appropriate quantities of A.R. calcium chloride and A.R. sodium carbonate. Suspend the calcium carbonate in water and add a solution containing 1 g. of palladium chloride. Warm the suspension until all the palladium is precipitated as the hydroxide upon the calcium carbonate, i.e., until the supernatant liquid is colourless. Wash several times with... 

The above catalysts contain about 30 per cent, of metal catalyst with 10 per cent, of metal may be readily prepared by reducing the quantity of platinum or palladium chloride used. 

Palladium catalysts are useful alternatives to Adams platinum oxide catalyst described in Section 111,150. The nearest equivalent to the latter is palladium chloride upon carbon and it can be stored indefinitely the palladium salt is reduced to the metal as required ... 

C. Palladium on carbon catalyst (5 per cent. Pd). Suspend 41-5 g. of nitric acid - washed activated carbon in 600 ml. of water in a 2-litre beaker and heat to 80°. Add a solution of 4 1 g. of anhydrous palladium chloride (1) in 10 ml. of concentrated hydrochloric acid and 25 ml. of water (prepared as in A), followed by 4 ml. of 37 per cent, formaldehyde solution. Stir the suspension mechanically, render it alkaUne to litmus with 30 per cent, sodium hydroxide solution and continue the stirring for a further 5 minutes. Filter off the catalyst on a Buchner funnel, wash it ten times with 125 ml. portions of water, and dry and store as in B. The yield is 46 g. 

Alternatively, the equivalent quantity of palladium chloride dihydrate may be used. 

METHOD 2 Without a doubt, this is the current world favorite for making P2Ps. This method is known as the Wacker oxidation and involves mixing safrole (or any other allylbenzene), palladium chloride, cuprous chloride and dimethylformamide in an oxygen atmosphere to get MD-P2P very quickly and in a totally clean manner [11, 12]. There s also a very nice review in ref. 13. 

The above reagents (ok the safrole and H2O aren t reagent) are weighed or measured accordingly. The flask is securely clamped into place on the magnetic stirrer. Add the DMF and H2O. Start stirring, and then slowly add the palladium chloride and cuprous chloride. If you add the powders first then the liquids you ll have problems with the stir bar finding a place to spin. 

After 24 hours, the stirring is stopped. Now it s time to fitter out the Cuprous Chloride, which is one of the two slight nuisances regarding this procedure. Note forget about Palladium Chloride recovery. It s too complex for the simplicity of this procedure and purchased from a photo supplier it shouldn t cost more than 6.50 per gram. We ll call this next process Phase Two. 

Palladium Chloride 26.5 grams (50% less big saving in ) Cuprous Chloride 300 grams (could have cut this to 200 g)... 

Example 51 Add. 1 mole of 3-(3,4-methylenedioxyphenyl) propylene,. 25 mole of methyl nitrite., 5L of methanol, 36g of water,. 00025 mole of trimethylamine, and. 0005 mole of palladium chloride as a catalyst to a flask. Stir magnetically for 1.5 hours at 25C. The conversion of the starting material was 92%, the yield of MDP-2-P was 83% and the Pd Turnover Number was 166. 

Example 86 A 0.10 mole amount of the starting 3-(4-hydroxyphenyl) propylene, 0.25 mole of methyl nitrite, 0.5 liter of methyl alcohol, and 0.006 mole of a palladium chloride catalyst were charged into a reaction vessel. Then, the reaction was carried out at a temperature of 20.degree. C. for 1.5hours."... 

Phenylpropanolamine. - With catalyst prepared as previously described from 0.5g of palladium chloride and 3g of charcoal, it was possible to reduce two portions of 9.8g of isonitrosopropio-phenone (0.06 mol), dissolved in 150 cc. of absolute alcohol containing 7. Og of hydrogen chloride, to phenylpropanolamine in from 145 - 190 minutes with yields of the isolated chloride from 9.4g to 11. Og, or 84 to 98% of the theoretical. After recrystallization from absolute alcohol the salt melted at 191°. The free base was obtained by treating an aqueous solution of the hydrochloride with alkali on cooling, the liberated amino alcohol solidified and after recrystallization from water melted at 103°."... 

Vinyl acetate reacts with the alkenyl triflate 65 at the /3-carbon to give the 1-acetoxy-1,3-diene 66[68]. However, the reaction of vinyl acetate with 5-iodo-pyrimidine affords 5-vinylpyrimidine with elimination of the acetoxy group[69]. Also stilbene (67) was obtained by the reaction of an excess of vinyl acetate with iodobenzene when interlamellar montmorillonite ethylsilyl-diphenylphosphine (L) palladium chloride was used as an active catalyst[70]. Commonly used PdCl2(Ph3P)2 does not give stilbene. 

With a palladium chloride catalyst, butenediol is carbonylated by carbon monoxide, giving 3-hexenedioic acid [4436-74-2] C HgO (94). 

With palladium chloride catalyst, carbon monoxide, and an alcohol the labile hydroxyl is alkylated during carbonylation (199). 

The direct oxidation of ethylene is used to produce acetaldehyde (qv) ia the Wacker-Hoechst process. The catalyst system is an aqueous solution of palladium chloride and cupric chloride. Under appropriate conditions an olefin can be oxidized to form an unsaturated aldehyde such as the production of acroleia [107-02-8] from propjiene (see Acrolein and derivatives). 

More recently, a commercial process has been introduced for the manufacture of methyl isocyanate (MIC) which involves the dehydrogenation of /V-m ethyl form am i de [123-39-7] in the presence of palladium, platinum [7440-06-4], or mthenium [7440-18-8], at temperatures between 50—300°C (31). Aprotic solvents, such as ben2ene [71-43-2], xylenes, or toluene [108-88-3], may optionally be used. A variation of this synthesis employs stoichiometric amounts of palladium chloride [7647-10-1], PdCl2. 

Oxidative Garbonylation. Carbon monoxide is rapidly oxidized to carbon dioxide however, under proper conditions, carbon monoxide and oxygen react with organic molecules to form carboxyUc acids or esters. With olefins, unsaturated carboxyUc acids are produced, whereas alcohols yield esters of carbonic or oxalic acid. The formation of acryUc and methacrylic acid is carried out in the Hquid phase at 10 MPa (100 atm) and 110°C using palladium chloride or rhenium chloride catalysts (eq. 19) (64,65). 

Dimethyl carbonate [616-38-6] and dimethyl oxalate [553-90-2] are both obtained from carbon monoxide, oxygen, and methanol at 363 K and 10 MPa (100 atm) or less. The choice of catalyst is critical cuprous chloride (66) gives the carbonate (eq. 20) a palladium chloride—copper chloride mixture (67,68) gives the oxalate, (eq. 21). Anhydrous conditions should be maintained by removing product water to minimize the formation of by-product carbon dioxide. 

The palladium chloride process for oxidizing olefins to aldehydes in aqueous solution (Wacker process) apparendy involves an intermediate anionic complex such as dichloro(ethylene)hydroxopalladate(II) or else a neutral aqua complex PdCl2 (CH2=CH2)(H2 0). The coordinated PdCl2 is reduced to Pd during the olefin oxidation and is reoxidized by the cupric—cuprous chloride couple, which in turn is reoxidized by oxygen, and the net reaction for any olefin (RCH=CH2) is then... 

Catalysts for dielectric surfaces are more complex than the simple salts used on metals. The original catalysts were separate solutions of acidic staimous chloride [7772-99-8J, used to wet the surface and deposit an adherent reducing agent, and acidic palladium chloride [7647-10-17, which was reduced to metallic palladium by the tin. This two-step catalyst system is now essentially obsolete. One-step catalysts consist of a stabilized, pre-reacted solution of the palladium and staimous chlorides. The one-step catalyst is more stable, more active, and more economical than the two-step catalyst (21,23). A separate acceleration or activation solution removes loose palladium and excess tin before the catalyzed part is placed in the electroless bath, prolonging bath life and stability. 

Catalysis is done by an acidic solution of the stabilized reaction product of stannous chloride and palladium chloride. Catalyst absorption is typically 1—5 p-g Pd per square centimeter. Other precious metals can be used, but they are not as cost-effective. The exact chemical identity of this catalyst has been a matter of considerable scientific interest (19—21,23). It seems to be a stabilized coUoid, co-deposited on the plastic with excess tin. The industry trends have been to use higher activity catalysts at lower concentrations and higher temperatures. Typical usage is 40—150 ppm of palladium at 60°C maximum, and a 30—60-fold or more excess of stannous chloride. Catalyst variations occasionally used include alkaline and non-noble metal catalysts. 

The reaction is carried out ia a bubble column at 120—130°C and 0.3 MPa (3 bar). Palladium chloride is reduced to palladium duriag the reaction, and then is reoxidized by cupric chloride. Oxygen converts the reduced cuprous chloride to cupric chloride. 

Palladium chloride from Inulsho Precious Metal Company, Japan, was used without purification. 

B. Palladium on carhon catalyst (5% Pd). A suspension of 93 g. of nitric acid-washed Darco G-60 (Note 10) in 1.21. of water contained in a 4-1. beaker (Notes 3 and 4) is heated to 80°. To this is added a solution of 8.2 g. (0.046 mole) of palladium chloride in 20 ml. (0.24 mole) of concentrated hydrochloric acid and 50 ml. of water (Note 2). Eight milliliters (0.1 mole) of 37% formaldehyde solution is added. The suspension is made slightly alkaline to litmus with 30% sodium hydroxide solution, constant stirring being maintained. The suspension is stirred 5 minutes longer. The catalyst is collected on a filter and washed ten times with 250-ml. portions of water. After removal of as much water as possible by filtration, the filter cake is dried (Note 11), first in air at room temperature, and then over potassium hydroxide in a desiccator. The dry catalyst (93-98 g.) is stored in a tightly closed bottle. 

---