Stoichiometric amount

Mercuryill) iodide, Hglj, is coloured either red or yellow, and is precipitated (yellow, turning red) by adding the stoichiometric amount of iodide ion to a solution containing mercury(II) ... 

Reagent can be used in close to stoichiometric amounts w/ substrate... 

Note 1. A slight excess of phenol was used. With a stoichiometric amount the solution may be too strongly basic, so that the further isomerization will become too fast. 

Of course, these schemes indicate only that the overall reactions may be classified as nucleophilic 1,3-substitutions and, in the last case, as electrophilic 1,3-substitut ions. The reactions often proceed only in the presence of catalytic or stoichiometric amounts of transition metal salts, while in their absence 1,1--substitutions or other processes are observed. The 1,1-substitutions are also catalyzed by salts of transition metals, and it is not yet well understood, which factors influence the 1,1 to 1,3-ratio. In a number of 1,3-Substitutions there is... 

Palladation of aromatic compounds with Pd(OAc)2 gives the arylpalladium acetate 25 as an unstable intermediate (see Chapter 3, Section 5). A similar complex 26 is formed by the transmetallation of PdX2 with arylmetal compounds of main group metals such as Hg Those intermediates which have the Pd—C cr-bonds react with nucleophiles or undergo alkene insertion to give oxidized products and Pd(0) as shown below. Hence, these reactions proceed by consuming stoichiometric amounts of Pd(II) compounds, which are reduced to the Pd(0) state. Sometimes, but not always, the reduced Pd(0) is reoxidized in situ to the Pd(II) state. In such a case, the whole oxidation process becomes a catalytic cycle with regard to the Pd(II) compounds. This catalytic reaction is different mechanistically, however, from the Pd(0)-catalyzed reactions described in the next section. These stoichiometric and catalytic reactions are treated in Chapter 3. 

The carbonylation of COD PdCl2 complex in aqueous sodium acetate produces /rui7x-2-hydroxy-5-cyclooctenecarboxylic acid /i-lactone (240). The lactone is obtained in 79% yield directly by the carbonylation of the COD complex in aqueous sodium acetate solution[220]. /i-Propiolactone (241) is obtained in 72% yield by the reaction of the PdCC complex of ethylene with CO and water in MeCN at —20 " C. /3-Propiolactone synthesis can be carried out with a catalytic amount of PdCC and a stoichiometric amount of CuCl2[221]. 

The intramolecular oxidative earbonylation has wide synthetie applieation. The 7-lactone 247 is prepared by intramolecular oxycarbonylation of the alke-nediol 244 with a stoichiometric amount of Pd(OAc)2 under atmospheric pres-sure[223]. The intermediate 245 is formed by oxypalladation, and subsequent CO insertion gives the acylpalladium 246. The oxycarbonylation of alkenols and alkanediols can be carried out with a catalytic amount of PdCl2 and a stoichiometric amount of CuCb, and has been applied to the synthesis of frenolicin(224] and frendicin B (249) from 248[225]. The carbonylation of the 4-penten-l,3-diol 250, catalyzed by PdCl2 and CuCl2, afforded in the c -3-hydroxytetrahydrofuran-2-aeetie acid lactone 251[226J. The cyclic acetal 253 is prepared from the dienone 252 in the presence of trimethyl orthoformate as an accepter of water formed by the oxidative reaction[227]. 

It is possible to prepare 1-acetoxy-4-chloro-2-alkenes from conjugated dienes with high selectivity. In the presence of stoichiometric amounts of LiOAc and LiCl, l-acetoxy-4-chloro-2-hutene (358) is obtained from butadiene[307], and cw-l-acetoxy-4-chloro-2-cyclohexene (360) is obtained from 1.3-cyclohexa-diene with 99% selectivity[308]. Neither the 1.4-dichloride nor 1.4-diacetate is formed. Good stereocontrol is also observed with acyclic diene.s[309]. The chloride and acetoxy groups have different reactivities. The Pd-catalyzed selective displacement of the chloride in 358 with diethylamine gives 359 without attacking allylic acetate, and the chloride in 360 is displaced with malonate with retention of the stereochemistry to give 361, while the uncatalyzed reaction affords the inversion product 362. 

In order to make these oxidative reactions of 1,3-dienes catalytic, several reoxidants are used. In general, a stoichiometric amount of benzoquinone is used. Furthermore, Fe-phthalocyanine complex or Co-salen complex is used to reoxidize hydroquinone to benzoquinone. Also, it was found that the reaction is faster and stereoselectivity is higher when (phenylsulflnyl)benzoquinone (383) is used owing to coordination of the sulfinyl group to Pd, Thus the reaction can be carried out using catalytic amounts of PdfOAcji and (arylsulfinyl)benzoquinone in the presence of the Fe or Co complex under an oxygen atmosphere[320]. Oxidative dicyanation of butadiene takes place to give l,4-dicyano-2-butene(384) (40%) and l,2-dicyano-3-butene (385)[32l]. 

Alcohols are oxidized slowly with PdCh. Oxidation of secondary alcohols to ketones is carried out with a catalytic amount of PdCh under an oxygen atmo-sphere[73.74]. Also, selective oxidation of the allylic alcohol 571 without attacking saturated alcohols is possible with a stoichiometric amount of PdfOAc) in aqueous DMF (1% H OifSll],... 

The intramolecular version for synthesizing cyclic and polycyclic compounds offers a powerful synthetic method for naturally occurring macrocyclic and polycyclic compounds, and novel total syntheses of many naturally occurring complex molecules have been achieved by synthetic designs based on this methodology. Cyclization by the coupling of an enone and alkenyl iodide has been applied to the synthesis of a model compound of l6-membered car-bomycin B 162 in 55% yield. A stoichiometric amount of the catalyst was used because the reaction was carried out under high dilution conditions[132]. 

Addition of a hydroxy group to alkynes to form enol ethers is possible with Pd(II). Enol ether formation and its hydrolysis mean the hydration of alkynes to ketones. The 5-hydroxyalkyne 249 was converted into the cyclic enol ether 250[124], Stereoselective enol ether formation was applied to the synthesis of prostacyclin[131]. Treatment of the 4-alkynol 251 with a stoichiometric amount of PdCl2, followed by hydrogenolysis with formic acid, gives the cyclic enol ether 253. Alkoxypalladation to give 252 is trans addition, because the Z E ratio of the alkene 253 was 33 1. 

The first report on the Pd(II)-promoted Cope rearrangement is the conversion of fw./ra/w-l,5-cyclodecadiene (44) into c/5-l,2-divinylcyclohexane-PdCl2 complex (45) with a stoichiometric amount of PdCl2(PhCN)2 at room temperature. The complex formation is the driving force of this unusual rearrangement [38,39]. A similar transformation of germacrane (l,5-dimethyl-8-isopropyli-dene-/rfflu,/ra j-l,5-cyclodecadiene) takes place[40j. 

A-2-Oxazoline-5-one (2091 when treated with thioacetic acid yields the corresponding thiazoline-5-one (210) (Scheme 107) (458. 461). These results have been questioned recently (365) however, it appears in the later report that a large excess of thioacetic acid was used instead o-f the stoichiometric amount previously used. 

Instead, an excess of KI is added, reducing the analyte and liberating a stoichiometric amount of The amount of produced is then determined by a back titration using Na2S203 as a reducing titrant. 

Besides pH, other preparative variables that can affect the microstructure of a gel, and consequendy, the properties of the dried and heat-treated product iaclude water content, solvent, precursor type and concentration, and temperature (9). Of these, water content has been studied most extensively because of its large effect on gelation and its relative ease of use as a preparative variable. In general, too Httie water (less than one mole per mole of metal alkoxide) prevents gelation and too much (more than the stoichiometric amount) leads to precipitation (3,9). Other than the amount of water used, the rate at which it is added offers another level of control over gel characteristics. 

Secondary acetylenic alcohols are prepared by ethynylation of aldehydes higher than formaldehyde. Although copper acetyUde complexes will cataly2e this reaction, the rates are slow and the equiUbria unfavorable. The commercial products are prepared with alkaline catalysts, usually used in stoichiometric amounts. 

Ethynylation of ketones is not cataly2ed by copper acetyUde, but potassium hydroxide has been found to be effective (180). In general, alcohols are obtained at lower temperatures and glycols at higher temperatures. Most processes use stoichiometric amounts of alkaU, but tme catalytic processes for manufacture of the alcohols have been described the glycols appear to be products of stoichiometric ethynylation only. 

In early work, vinyl chloride had been heated with stoichiometric amounts of alkaU alkoxides in excess alcohol as solvent, giving vinyl ethers as products (210). Supposedly this involved a Williamson ether synthesis, where alkaU alkoxide and organic haUde gave an ether and alkaU haUde. However, it was observed that small amounts of acetylene were formed by dehydrohalogenation of vinyl chloride, and that this acetylene was consumed as the reaction proceeded. Hence acetylene was substituted for vinyl chloride and only catalytic amounts of alkaU were used. Vinylation proceeded readily with high yields (211). 

The stoichiometric and the catalytic reactions occur simultaneously, but the catalytic reaction predominates. The process is started with stoichiometric amounts, but afterward, carbon monoxide, acetylene, and excess alcohol give most of the acrylate ester by the catalytic reaction. The nickel chloride is recovered and recycled to the nickel carbonyl synthesis step. The main by-product is ethyl propionate, which is difficult to separate from ethyl acrylate. However, by proper control of the feeds and reaction conditions, it is possible to keep the ethyl propionate content below 1%. Even so, this is significantly higher than the propionate content of the esters from the propylene oxidation route. 

The most common catalysts are sodium hydroxide and calcium hydroxide, generally used at a modest excess over the nominal stoichiometric amount to avoid formaldehyde-only addition reactions. Calcium hydroxide is cheaper than NaOH, but the latter yields a more facile reaction and separation of the product does not require initial precipitation and filtration of the metal formate (57). 

Lime Soda. Process. Lime (CaO) reacts with a dilute (10—14%), hot (100°C) soda ash solution in a series of agitated tanks producing caustic and calcium carbonate. Although dilute alkaH solutions increase the conversion, the reaction does not go to completion and, in practice, only about 90% of the stoichiometric amount of lime is added. In this manner the lime is all converted to calcium carbonate and about 10% of the feed alkaH remains. The resulting slurry is sent to a clarifier where the calcium carbonate is removed, then washed to recover the residual alkaH. The clean calcium carbonate is then calcined to lime and recycled while the dilute caustic—soda ash solution is sent to evaporators and concentrated. The concentration process forces precipitation of the residual sodium carbonate from the caustic solution the ash is then removed by centrifugation and recycled. Caustic soda made by this process is comparable to the current electrolytic diaphragm ceU product. 

Hexafluoroantimonic acid [72121 -43-8] HSbF 6H20, is prepared by dissolving freshly prepared hydrous antimony pentoxide ia hydrofluoric acid or adding the stoichiometric amount of 70% HF to SbF. Both of these reactions are exothermic and must be carried out carefully. 

Germanium difluoride can be prepared by reduction (2,4) of GeF by metallic germanium, by reaction (1) of stoichiometric amounts of Ge and HF in a sealed vessel at 225°C, by Ge powder and HgF2 (5), and by GeS and PbF2 (6). Gep2 has been used in plasma chemical vapor deposition of amorphous film (see Plasma TECHNOLOGY Thin films) (7). 

The other important direct alkylation processes involve reaction of electron-rich olefinic compounds with either tin metal or stannous chloride (tin(II) chloride) in the presence of stoichiometric amounts of hydrogen chloride (22). Butyl acrylate (R = C Hg) was used commercially in this process to prepare the estertin or P-carboalkoxyethyltin chlorides as iHustrated in the foUowing. 

The selectivity to alcohol in LPO may be significantly increased when boric acid, meta-hotic acid, or boric anhydride is present in stoichiometric amounts (2). The boron compounds appear to convert alkyUiydroperoxides to alkyl borates and may also intercept alkylperoxy radicals, converting them to alkylperoxyboron compounds these are later converted to alkyl borates. The alkyl borates are resistant to further oxidation they are hydrolyzed to recover alcohols. 

The reaction of a hydroperoxide with 2-methylaziridine [75-55-8] has been described (94). The reaction of ethyleneknine with phenols (95) and carboxyHc acids (96,97) produces ethylamine ethers and esters, respectively. However, these reactions frequentiy yield product mixtures which contain polyaminoalkylated oxygen nucleophiles and polymers, in addition to the desked products (1). The selectivity of the reaction can often be improved by using less than the stoichiometric amount of the aziridine component (98,99). 

Stoichiometric Air. If the stoichiometric amount of air is added to the combustion zone, the temperature ia that zoae is coatroUed by removing heat from the system. No eaergy leaves the system as chemical eaergy. The heat is removed by an external means such as generating steam or gas quenching. 

More recently, a commercial process has been introduced for the manufacture of methyl isocyanate (MIC) which involves the dehydrogenation of /V-m ethyl form am i de [123-39-7] in the presence of palladium, platinum [7440-06-4], or mthenium [7440-18-8], at temperatures between 50—300°C (31). Aprotic solvents, such as ben2ene [71-43-2], xylenes, or toluene [108-88-3], may optionally be used. A variation of this synthesis employs stoichiometric amounts of palladium chloride [7647-10-1], PdCl2. 

Water hydroly2es pure diketene only slowly to give acetoacetic acid [541-50-4] which quickly decomposes to acetone and carbon dioxide, but increasing the pH or adding catalysts (amines, palladium compounds) increases the rate of hydrolysis. The solvolysis of diketene in ammonia results in aceto acetamide [5977-14-0] if used in stoichiometric amounts (99), and P-arninocrotonarnide [15846-25-0] if used in excess (100). 

The lanthanum phosphate phosphor is usually prepared by starting with a highly purified coprecipitated oxide of lanthanum, cerium, and terbium blended with a slight excess of the stoichiometric amount of diammonium acid phosphate. Unlike the case of the aluminate phosphor, firing is carried out in an only slightly reducing or a neutral atmosphere of nitrogen at a temperature 1000° C. Also this phosphor is typically made with the addition of a flux,... 

Since there are no volatile components this halophosphate phosphor is prepared with close to the stoichiometric amounts of SrHPO, SrCO, CaCO, BaCO, SrCl2, or NH Cl and EU2O2. The blend is fired under an atmosphere containing 1—2% hydrogen at 1100°C. A small excess of chloride provides some fluxing action and gives weU-formed crystals of apatite. The chlorapatites are dimorphous one modification is hexagonal and the other monoclinic. 

The lower equivalent weight of magnesium hydroxide compared to caustic soda, hydrated lime, and soda ash reduces the stoichiometric amounts necessary to neutralize a given amount of acid. Depending on relative alkah costs, magnesium hydroxide can offer the advantage of lower chemical costs. 

Merbrornin/725 -/ )-< 7, disodium2,7-dibromo-4-hydroxymercuri luoresceiQ, (2), commonly called mercurochrome, is prepared by refluxing dibromofluoresceia with mercuric acetate ia acetic acid. The precipitate is dissolved ia water containing the stoichiometric amount of sodium hydroxide and evaporated. 

Merthiolate/T4- )4-< 7 (3), sodium ethyLmercurithiosahcylate, known also as thimersol, is prepared from a 1 1 ratio of ethyhnercuric chloride/7(97-27-. and disodium thiosahcylate ia ethanol. After removal of the sodium chloride by filtration, the free acid is precipitated by acidification with dilute sulfuric acid. Purification is achieved by recrystallization from 95% ethanol, and the product, merthiolate, is obtained by neutralization with a stoichiometric amount of sodium hydroxide. 

---