Nanocomposites preparation techniques

The increase in dielectric constant is attributed to the formation of many small capacitors of fillers (electrodes) with a dielectric thin polymer film between them, which can increase the dielectric constant. The distribution of the fillers inside of the polymer can highly affect the dielectric constant. The filler distribution depends on nanocomposite preparation techniques. 

Applications of sol-gel-processed interphase catalysts. Chemical Reviews, 102, 3543-3578. Pierre, A.C. (2004) The sol-gel encapsulation of enzymes. Biocatalysis and Biotransformation, 22, 145-170. Shchipunov, Yu.A. (2003) Sol-gel derived biomaterials of silica and carrageenans. Journal of Colloid and Interface Science, 268, 68-76. Shchipunov Yu.A. and Karpenko T.Yu. (2004) Hybrid polysaccharide-silica nanocomposites prepared by the sol-gel technique. Langmuir, 20, 3882-3887. 

Morphological structures and properties of a series of poly(ethyl acrylate)/clay nanocomposites prepared by the two distinctively different techniques of in situ ATRP and solution blending were studied by Datta et al. [79]. Tailor-made PNCs with predictable molecular weights and narrow polydispersity indices were prepared at different clay loadings. WAXD and studies revealed that the in situ approach is the better option because it provided an exfoliated morphology. By contrast, conventional solution blending led only to interlayer expansion of the clay gallery. 

The effect of the microstructure of acrylic copolymer/terpolymer on the properties of silica-based nanocomposites prepared by the sol-gel technique using TEOS has been further studied by Patel et al. [144]. The composites demonstrate superior tensile strength and tensile modulus with increasing proportion of TEOS up to a certain level. At a particular TEOS concentration, the tensile properties improve with increasing hydrophilicity of the polymer matrix and acrylic acid modification. 

Abstract Hybrid metal/metal oxide-poly-/>ara-xylylene (PPX) nanocomposites have attracted great interest, because of a broad spectrum of applications. A simple, low-cost preparation technique has been developed and comprises a cold-wall vacuum co-deposition technique. This co-deposition technique has been applied to synthesize nanocomposites, containing PPX and nanoparticles of Al, Sn, Zn, Ti and their oxides. Important is the oxidation kinetics of the metal clusters to their oxides in relation to the percolation threshold. 

Nanocomposite Preparation Method Thin Film/Layer Formation Technique Sensing Chemicals Ref. 

Epoxy-modified Mesua ferrea L. seed oil-based conventional polyurethane nanocomposites prepared by an ex situ solution technique under high mechanical shearing and ultrasonication at room temperature with different (1,2.5 and 5) wt% loadings of clay have been evaluated as biocompatible materials. The partially exfoliated nanocomposites exhibited two- and... 

Bisphenol-A-based epoxy with a poly(amido amine) hardener system cured Mesuaferrea L. seed oil-based hyperbranched polyurethane (HBPU)/ clay nanocomposites obtained by an ex situ solution technique, was also reported. The partially exfoliated nanocomposites showed a two-fold improvement in adhesive strength and scratch hardness, 10 MPa increments in tensile strength and thermostability at 112°C with little effect on impact resistance, bending and elongation at break compared to a pristine epoxy-modified HBPU system. However, similar epoxy-cured Mesua ferrea L. seed oil-based HBPU/clay nanocomposites exhibited a two-fold increase in tensile strength, a 6°C increase in melting point and thermostability at 111°C after nanocomposite formation using an in situ technique. An excellent shape recovery of about 96-99% was observed for the nanocomposites. The above observations confirm that the performance characteristics of nanocomposites are influenced by their preparation technique. 

The ranges in which the clay platelets were present in the in-situ polymerized and melt-blended nanocomposite samples are given in Table 9.5. The average length of clay platelets seems to be approximately 65 nm for in-situ polymerized nanocomposites, whereas it is 100 nm for the nanocomposites prepared by melt intercalation technique. 

Carbon-based polymer nano composites represent an interesting type of advanced materials with structural characteristics that allow them to be applied in a variety of fields. Functionalization of carbon nanomaterials provides homogeneous dispersion and strong interfacial interaction when they are incorporated into polymer matrices. These features confer superior properties to the polymer nanocomposites. This chapter focuses on nanodiamonds, carbon nanotubes and graphene due to their importance as reinforcement fillers in polymer nanocomposites. The most common methods of synthesis and functionalization of these carbon nanomaterials are explained and different techniques of nanocomposite preparation are briefly described. The performance achieved in polymers by the introduction of carbon nanofillers in the mechanical and tribological properties is highlighted, and the hardness and scratching behavior of the nanocomposites are also discussed. 

The preparative techniques for the production of bio nanocomposites are based largely on existing techniques for the processing of ordinary plastics. The processes can be classified into three main categories (41) ... 

Alexandre, M., Dubois, R, Sun, T., Garces, J. M., and Jerome, R. 2002. Rolyethylene-layered silicate nanocomposites prepared by the polymerization-filling technique S5mthesis and mechanical properties. Polymer 43 2123-2132. 

---