Industrial processes alcohols

Among the properties sought in the solvent are low cost, avadabihty, stabiUty, low volatiUty at ambient temperature, limited miscibility in aqueous systems present in the process, no solvent capacity for the salts, good solvent capacity for the acids, and sufficient difference in distribution coefficient of the two acids to permit their separation in the solvent-extraction operation. Practical solvents are C, C, and alcohols. For industrial process, alcohols are the best choice (see Amyl alcohols). Small quantities of potassium nitrate continue to be produced from natural sources, eg, the caUche deposits in Chile. 

The industrial process for preparing the reagent usually permits a little hydrolysis to occur, and the product may contain a little free calcium hydroxide or basic chloride. It cannot therefore be employed for drying acids or acidic liquids. Calcium chloride combines with alcohols, phenols, amines, amino-acids, amides, ketones, and some aldehydes and esters, and thus cannot be used with these classes of compounds. 

Higher aliphatic alcohols (C —C g) are produced ia a number of important industrial processes using petroleum-based raw materials. These processes are summarized in Table 1, as are the principal synthetic products and most important feedstocks (qv). Worldwide capacity for all higher alcohols was approximately 5.3 million metric tons per annum in early 1990, 90% of which was petroleum-derived. Table 2 Hsts the major higher aliphatic alcohol producers in the world in early 1990. 

Table 1. Synthetic Industrial Processes for Higher Aliphatic Alcohols...

Sasol produces synthetic fuels and chemicals from coal-derived synthesis gas. Two significant variations of this technology have been commercialized, and new process variations are continually under development. Sasol One used both the fixed-bed (Arge) process, operated at about 240°C, as weU as a circulating fluidized-bed (Synthol) system operating at 340°C. Each ET reactor type has a characteristic product distribution that includes coproducts isolated for use in the chemical industry. Paraffin wax is one of the principal coproducts of the low temperature Arge process. Alcohols, ketones, and lower paraffins are among the valuable coproducts obtained from the Synthol process. 

Nitromethane. The nitroparaffins are used widely as raw materials for synthesis. Nitromethane is used to produce the nitro alcohol (qv) 2-(hydroxymethyl)-2-nitro-l,3-propanediol, which is a registered biocide useful for control of bacteria in a number of industrial processes. This nitro alcohol also serves as the raw material for the production of the alkanolamine (qv) 2-amino-2-(hydroxymethyl)-l,3-propanediol, which is an important buffering agent useful in a number of pharmaceutical appHcations. 

In the early years of the chemical industry, use of biological agents centered on fermentation (qv) techniques for the production of food products, eg, vinegar (qv), cheeses (see Milk and milk products), beer (qv), and of simple organic compounds such as acetone (qv), ethanol (qv), and the butyl alcohols (qv). By the middle of the twentieth century, most simple organic chemicals were produced synthetically. Fermentation was used for food products and for more complex substances such as pharmaceuticals (qv) (see also Antibiotics). Moreover, supports were developed to immobilize enzymes for use in industrial processes such as the hydrolysis of starch (qv) (see Enzyme applications). 

Fermentation An anaerobic bioprocess. An enzymatic transformation of organic substrates, especially carbohydrates, generally accompanied by the evolution of gas as a byproduct. Fermentation is used in various industrial processes for the manufacture of products (e.g., alcohols, organic acids, solvents, and cheese) by the addition of yeasts, moulds, and bacteria. 

In a widely used industrial process, the mixture of ethylene and propene that is obtained by dehydrogenation of natural gas is passed into concentrated sulfuric acid. Water is added, and the solution is heated to hydrolyze the alkyl hydrogen sulfate. The product is almost exclusively a single alcohol. Is this alcohol ethanol, 1-propanol, or 2-propanol Why is this particular one formed almost exclusively ... 

Out of the metal oxides, sulfated titania and tin oxide performed slightly better than the sulfated zirconia (SZ) catalyst and niobic acid (Nb205). However, SZ is cheaper and readily available on an industrial scale. Moreover, it is already applied in several industrial processes (7,8). Zirconia can be modified with sulfate ions to form a superacidic catalyst, depending on the treatment conditions (11-16). In our experiments, SZ showed high activity and selectivity for the esterification of fatty acids with a variety of alcohols, from 2-ethylhexanol to methanol. Increasing... 

Attempts to achieve selective oxidations of hydrocarbons or other compounds when the desired site of attack is remote from an activating functional group are faced with several difficulties. With powerful transition-metal oxidants, the initial oxidation products are almost always more susceptible to oxidation than the starting material. When a hydrocarbon is oxidized, it is likely to be oxidized to a carboxylic acid, with chain cleavage by successive oxidation of alcohol and carbonyl intermediates. There are a few circumstances under which oxidations of hydrocarbons can be synthetically useful processes. One group involves catalytic industrial processes. Much effort has been expended on the development of selective catalytic oxidation processes and several have economic importance. We focus on several reactions that are used on a laboratory scale. 

The reduction of nitrobenzene to aniline is a major industrial process at the heart of the production of polyurethanes, and it is also often used as a marker reaction to compare activities of catalysts [1,2], It can be performed over a variety of catalysts and in a variety of solvents. As well as its main use in polymethanes, aniline is used in a wide range of industries such as dyes, agrochemicals, by further reaction and functionalisation. Reductive alkylation is one such way of functionalising aromatic amines [3, 4], The reaction usually takes place between an amine and a ketone, aldehyde or alcohol. However it is possible to reductively alkylate direct from the nitro precursor to the amine and in this way remove a processing step. In this study we examined the reductive alkylation of nitrobenzene and aniline by 1-hexanol. 

How many grams of methyl alcohol, CH,OH, can be obtained in an industrial process from 10.0 X 10Ag (lO.Ometric tons) of CO plus hydrogen gas To calculate the answer, (a) write a... 

The acid-catalyzed addition of water to the double bond of an alkene is a method for the preparation of low molecular weight alcohols that has its greatest utility in large-scale industrial processes. 

Surfactants can be produced from both petrochemical resources and/or renewable, mostly oleochemical, feedstocks. Crude oil and natural gas make up the first class while palm oil (+kernel oil), tallow and coconut oil are the most relevant representatives of the group of renewable resources. Though the worldwide supplies of crude oil and natural gas are limited—estimated in 1996 at 131 X 1091 and 77 X 109 m3, respectively [28]—it is not expected that this will cause concern in the coming decades or even until the next century. In this respect it should be stressed that surfactant products only represent 1.5% of all petrochemical uses. Regarding the petrochemically derived raw materials, the main starting products comprise ethylene, n-paraffins and benzene obtained from crude oil by industrial processes such as distillation, cracking and adsorption/desorption. The primary products are subsequently converted to a series of intermediates like a-olefins, oxo-alcohols, primary alcohols, ethylene oxide and alkyl benzenes, which are then further modified to yield the desired surfactants. 

The oxidative carbonylation of alcohols and phenols to carbonates can be catalyzed by palladium or copper species [154-213]. This reaction is of particular practical importance, since it can be developed into an industrial process for the phosgene-free synthesis of dimethyl carbonate (DMC) and diphenyl carbonate (DPC), which are important industrial intermediates for the production of polycarbonates. Moreover, DMC can be used as an eco-friendly methylation and carbonylation agent [214,215]. The industrial production of DMC by oxidative carbonylation of methanol has been achieved by Enichem [216] and Ube [217]. 

Oxidation is the first step for producing molecules with a very wide range of functional groups because oxygenated compounds are precursors to many other products. For example, alcohols may be converted to ethers, esters, alkenes, and, via nucleophilic substitution, to halogenated or amine products. Ketones and aldehydes may be used in condensation reactions to form new C-C double bonds, epoxides may be ring opened to form diols and polymers, and, finally, carboxylic acids are routinely converted to esters, amides, acid chlorides and acid anhydrides. Oxidation reactions are some of the largest scale industrial processes in synthetic chemistry, and the production of alcohols, ketones, aldehydes, epoxides and carboxylic acids is performed on a mammoth scale. For example, world production of ethylene oxide is estimated at 58 million tonnes, 2 million tonnes of adipic acid are made, mainly as a precursor in the synthesis of nylons, and 8 million tonnes of terephthalic acid are produced each year, mainly for the production of polyethylene terephthalate) [1]. 

Since the oxidative polymerization of phenols is the industrial process used to produce poly(phenyleneoxide)s (Scheme 4), the application of polymer catalysts may well be of interest. Furthermore, enzymic, oxidative polymerization of phenols is an important pathway in biosynthesis. For example, black pigment of animal kingdom "melanin" is the polymeric product of 2,6-dihydroxyindole which is the oxidative product of tyrosine, catalyzed by copper enzyme "tyrosinase". In plants "lignin" is the natural polymer of phenols, such as coniferyl alcohol 2 and sinapyl alcohol 3. Tyrosinase contains four Cu ions in cataly-tically active site which are considered to act cooperatively. These Cu ions are presumed to be surrounded by the non-polar apoprotein, and their reactivities in substitution and redox reactions are controlled by the environmental protein. 

The balance of the industrial ethyl alcohol is in demand as a solvent in personal care products (aftershave lotion, mouthwash), inks, cosmetics, detergents, household cleaners, pharmaceuticals, industrial coatings, and as a processing solvent. 

Amberlyst 15 resin was found to catalyze the addition of primary alcohols to olefins. The activity displayed was higher than for soluble anhydrous p-toluenesul-fonic acid. The addition of methanol or -butanol to isobutene is weU-estabhshed as an industrial process [7]. 

The industrial process requires a large phosphine excess ([P]/[Rh] = 21 1) which can be easily provided by the extremely water-soluble TPPTS. However, the reactants are insoluble in such an aqueous phase, therefore the reaction is mn in the presence of co-solvents, usually alcohols. (Less soluble TPPMS performs better at [P]/[Rh] = 3, probably its surfactant properties help in solubilizing the diene and methyl acetoacetate.) The organic products are easily separated from the aqueous catalyst solution which can be recycled. 

---