Ethyl alcohol preparation

Uses Solvent for chlorinated rubber insecticide and bleach manufacturing paint, varnish and rust remover manufacturing degreasing, cleansing, and drying of metals denaturant for ethyl alcohol preparation of 1,1-dichloroethylene extractant and solvent for oils and fats insecticides weed killer fumigant intermediate in the manufacturing of other chlorinated hydrocarbons herbicide. 

A measured volume of the gas mixture to be examined is passed through a wash-bottle containing 50 ml. of a 1% solution of sodium peroxide in 50% ethyl alcohol prepared in the following manner 2 gm. sodium peroxide is dissolved in 100 ml. iced water and just before using 25 ml. of this solution is diluted with 25 ml. 95% alcohol. 

A porcine animal model of 40 different phenol-croton oil, hexachlorophene foam, and ethyl alcohol preparations noted that when any amount of croton oil was added, there was a more brisk inflanunatory response than when croton oil was not added [312]. Phenol peels were found to be deeper with increasing concentrations and with inCTeasing concentrations of croton oil, and multiple applications of phe-nol/croton oil increased the depth of the peel in this animal model [312]. 

Chemical methods may be employed if the reagent attacks only one of the components. Thus quicklime may be employed for the removal of water in the preparation of absolute ethyl alcohol. Also aromatic and unsaturated hydrocarbons may be removed from mixtures with saturated hydrocarbons by sulphonation. 

Absolute diethyl ether. The chief impurities in commercial ether (sp. gr. 0- 720) are water, ethyl alcohol, and, in samples which have been exposed to the air and light for some time, ethyl peroxide. The presence of peroxides may be detected either by the liberation of iodine (brown colouration or blue colouration with starch solution) when a small sample is shaken with an equal volume of 2 per cent, potassium iodide solution and a few drops of dilute hydrochloric acid, or by carrying out the perchromio acid test of inorganic analysis with potassium dichromate solution acidified with dilute sulphuric acid. The peroxides may be removed by shaking with a concentrated solution of a ferrous salt, say, 6-10 g. of ferrous salt (s 10-20 ml. of the prepared concentrated solution) to 1 litre of ether. The concentrated solution of ferrous salt is prepared either from 60 g. of crystallised ferrous sulphate, 6 ml. of concentrated sulphuric acid and 110 ml. of water or from 100 g. of crystallised ferrous chloride, 42 ml. of concentrated hydiochloric acid and 85 ml. of water. Peroxides may also be removed by shaking with an aqueous solution of sodium sulphite (for the removal with stannous chloride, see Section VI,12). 

Absolute ethyl alcohol. Ethyl alcohol of a high degree of purity is frequently required in preparative organic chemistry. For some purposes alcohol of ca. 99 -5 per cent, purity is satisfactory this grade may be purchased (the absolute alcohol of commerce), or it may be conveniently prepared by the dehydration of rectified spirit with quicklime. Rectified spirit is the constant boiling point mixture which ethyl alcohol forms with water, and usually contains 95 6 per cent, of alcohol by weight. Wherever the term rectified spirit is used in this book, approximately 95 per cent, ethyl alcohol is to be understood. 

Extremely dry (or super-dry ) ethyl alcohol. The yields in several organic preparations e.g., malonic ester syntheses, reduction with sodium and ethyl alcohol, veronal synthesis) are considerably improved by the use of alcohol of 99-8 per cent, purity or higher. This very high grade ethyl alcohol may be prepared in several ways from commercial absolute alcohol or from the product of dehydration of rectified spirit with quicklime (see under 4). 

Pure pyridine may be prepared from technical coal-tar pyridine in the following manner. The technical pyridine is first dried over solid sodium hydroxide, distilled through an efficient fractionating column, and the fraction, b.p. 114 116° collected. Four hundred ml. of the redistilled p)rridine are added to a reagent prepared by dissolving 340 g. of anhydrous zinc chloride in a mixture of 210 ml. of concentrated hydrochloric acid and 1 litre of absolute ethyl alcohol. A crystalline precipitate of an addition compound (probable composition 2C5H5N,ZnCl2,HCl ) separates and some heat is evolved. When cold, this is collected by suction filtration and washed with a little absolute ethyl alcohol. The yield is about 680 g. It is recrystaUised from absolute ethyl alcohol to a constant m.p. (151-8°). The base is liberated by the addition of excess of concentrated... 

Sodamide should never be stored in a stoppered bottle from which samples are to be removed intermittently, since dangerous mixtures may result when the substance is exposed for 2-3 days to even limited amounts of air at the ordinary temperature. As a safe practice, sodamide should be used immediately after preparation, and should not be kept longer than 12-24 hours unless it be under an inert solvent. Even small amounts of unused sodamide should be removed from the apparatus in which it was made by washing with methyl or ethyl alcohol. In all cases where a yellowish or brownish colour develops, due to the formation of oxidation... 

Three reactants. Ethyl iodide may be prepared by the interaction between iodine, ethyl alcohol and red phosphorus. The quantities employed and the yield obtained in a particular experiment are given below the equation. 

The 0 -S.V alcoholic potassium hydroxide solution Is prepared by dissolving 16g. of potassium hydroxide pellets in 500 ml. of alcohol (or industrial spirit) contained in a bottle closed by a cork. After standing for 24 hours, the clear solution is decanted or filtered from the residue of potassium carbonate. It is said that a solution in methyl alcohol has better keeping qualities than that in ethyl alcohol. 

The silver nitrite may be prepared as described in Section 11,50, 17. The product supplied by Johnson, Matthey and Co. Ltd., of Hatton Garden, London, E.C. 1, is satisfactory it. should be washed with absolute methyl or ethyl alcohol, followed by sodium-dried ether, and dried in an electrically-heated oven at 100 for 30 minutes (longer heating results in darkening on the surface) the substance should be kept in a vacuum desiccator until required. 

Diethyl ether may be prepared from ethyl alcohol by the sulphuric acid process. A mixture of alcohol and sulphuric acid in equimolecular proportions is heated to about 140° and alcohol is run in at the rate at which the ether produced distils from the reaction mixture. Ethyl hydrogen sulphate (or ethyl sulphuric acid) is first formed and this yields ether either by reacting directly with a molecule of alcohol or by the formation and alcoholysis of diethyl sulphate (I) ... 

Ethyl cyctopropane-carboxylate. Use 22 g. of cyciopropane-carb-oxyhc acid (Section V,33) and 40 g. (24-5 ml.) of redistiUed thionyl chloride to prepare the acid chloride, b.p. 118-119° (22 g.). Treat the latter with 10-1 g. of absolute ethyl alcohol. The yield of ethyl cyclo-propane-carboxylate, b.p. 132-133°, is 13 g. 

Ethyl bromoacetate (1). Fit a large modified Dean and Stark apparatus provided with a stopcock at the lower end (a convenient size is shown in Fig. Ill, 126, 1) to the 1-htre flask containing the crude bromoacetic acid of the previous preparation and attach a double surface condenser to the upper end. Mix the acid with 155 ml. of absolute ethyl alcohol, 240 ml. of sodium-dried benzene and 1 ml. of concentrated sulphuric acid. Heat the flask on a water bath water, benzene and alcohol will collect in the special apparatus and separate into two layers, the lower layer consisting of approximately 50 per cent, alcohol. Run ofi the lower layer (ca. 75 ml.), which includes all the water formed in the... 

Ethyl acetoacetate may be prepared by the action of sodium upon dry ethyl acetate and decomposition of the resulting sodio compound with dilute acetic acid. Most samples of ethyl acetate contain some ethyl alcohol and it is usually assumed that sodium ethoxidc is the condensing agent ... 

Thiocarbanilide is prepared by iieating a mixture of aniline and carbon disulphide in absolute ethyl alcohol ... 

In a 1 litre round-bottomed flask provided with an efficient double surface condenser, place 40 g. (39 ml.) of aniline, 50 g. (40 ml.) of carbon sulphide CAUTION inflammable) (1), and 50 g. (63-5 ml.) of absolute ethyl alcohol (2). Set up the apparatus in the fume cupboard or attach an absorption device to the top of the condenser (see Fig. 11, 8, 1) to absorb the hydrogen sulphide which is evolved. Heat upon an electrically-heated water bath or upon a steam bath for 8 hours or until the contents of the flask sohdify. When the reaction is complete, arrange the condenser for downward distillation (Fig. 11, 13, 3), and remove the excess of carbon disulphide and alcohol (CA UTION inflammable there must be no flame near the receiver). Shake the residue in the flask with excess of dilute hydrochloric acid (1 10) to remove any aniline present, filter at the pump, wash with water, and drain well. Dry in the steam oven. The yield of crude product, which is quite satisfactory for the preparation of phenyl iao-thiocyanute (Section IV.95), is 40-45 g. Recrystalhse the crude thiocarbanihde by dissolving it, under reflux, in boiling rectified spirit (filter through a hot water funnel if the solution is not clear), and add hot water until the solution just becomes cloudy and allow to cool. Pure sj/m.-diphenylthiourea separates in colourless needles, m.p, 154°,... 

Higher alkyl ethers are prepared by treating the sodium derivative of the phaiol (made by adding the phenol to a solution of sodium ethoxide in ethyl alcohol) with the alkyl iodide or bromide (Williamson synthesis), for example ... 

The following procedures may be used for the preparation of ethereal solutions of diazomethane containing ethyl alcohol they differ slightly according to as to whether large or small quantities are required. The presence of alcohol is not harmful for many appUcatioiis of diazomethane. (It may be pointed out that ethereal diazomethane solution prepared from nitrosomethylurea is free from alcohol.)... 

Girard s reagent P , C5H5NCH2C0NHNH2 C1. In a 1-htre threenecked flask, equipped as in the previous preparation, place 200 ml. of absolute ethyl alcohol, 63 g. (64 -5 ml.) of pure anhydrous pyridine and 98 - 5 g. (84 5 ml.) of ethyl chloroacetate. Heat the mixture under reflux for 2-3 hours until the formation of the quaternary salt is complete acidify a small test-portion with dilute sulphuric acid it should dissolve completely and no odour of ethyl chloroacetate should be apparent. Cool the mixture in ice and salt. Replace the thermometer by a dropping funnel, and add a solution of 40 g. of 100 per cent, hydrazine hydrate in 60 ml. of absolute ethanol all at once. A vigorous exothermic reaction soon develops and is accompanied by vigorous effervescence. The pro duct separates almost immediately. When cold, filter with suction, wash... 

Ethyl phenylethylmalonate. In a dry 500 ml. round-bottomed flask, fitted with a reflux condenser and guard tube, prepare a solution of sodium ethoxide from 7 0 g. of clean sodium and 150 ml. of super dry ethyl alcohol in the usual manner add 1 5 ml. of pure ethyl acetate (dried over anhydrous calcium sulphate) to the solution at 60° and maintain this temperature for 30 minutes. Meanwhile equip a 1 litre threenecked flask with a dropping funnel, a mercury-sealed mechanical stirrer and a double surface reflux condenser the apparatus must be perfectly dry and guard tubes should be inserted in the funnel and condenser respectively. Place a mixture of 74 g. of ethyl phenylmalonate and 60 g. of ethyl iodide in the flask. Heat the apparatus in a bath at 80° and add the sodium ethoxide solution, with stirring, at such a rate that a drop of the reaction mixture when mixed with a drop of phenolphthalein indieator is never more than faintly pink. The addition occupies 2-2 -5 hoius continue the stirring for a fiuther 1 hour at 80°. Allow the flask to cool, equip it for distillation under reduced pressure (water pump) and distil off the alcohol. Add 100 ml. of water to the residue in the flask and extract the ester with three 100 ml. portions of benzene. Dry the combined extracts with anhydrous magnesium sulphate, distil off the benzene at atmospheric pressure and the residue under diminished pressure. C ollect the ethyl phenylethylmalonate at 159-160°/8 mm. The yield is 72 g. 

Fluorescein test paper Is prepared by dipping filter paper into a dilute solution of fluorescein in ethyl alcohol it dries rapidly and is then ready for use. The test paper lias a lemon yellow colour. 

The residue in the flask is either a solution or a suspension of the potassium salt of the acid derived from the ester in diethylene glycol. Add 10 ml. of water and 10 ml. of ethyl alcohol to the residue and shake until thoroughly mixed. Then add a drop or two of phenolphthalein and dilute sulphuric acid, dropwise, until just acid. Allow the mixture to stand for about 5 minutes and then Alter the potassium sulphate. Use the clear filtrate for the preparation of a sohd derivative or two of the acid (see Section 111,85,4). 

When applied to the preparation of alkenes the reaction is carried out m the presence of a strong base such as sodium ethoxide (NaOCH2CH3) m ethyl alcohol as solvent... 

Show how ethyl alcohol could be used to prepare (a) CH3CN and (b) CH3CH2CN Along with ethyl alcohol you may use any necessary inorganic reagents... 

The saponification of 0 labeled ethyl propanoate was desenbed in Section 20 11 as one of the significant expenments that demonstrated acyl-oxygen cleavage in ester hydrolysis The 0 labeled ethyl propanoate used in this expenment was prepared from 0 labeled ethyl alcohol which in turn was obtained from acetaldehyde and 0 enriched water Wnte a senes of equations... 

Acetaldehyde [75-07-0] (ethanal), CH CHO, was first prepared by Scheele ia 1774, by the action of manganese dioxide [1313-13-9] and sulfuric acid [7664-93-9] on ethanol [64-17-5]. The stmcture of acetaldehyde was estabhshed in 1835 by Liebig from a pure sample prepared by oxidising ethyl alcohol with chromic acid. Liebig named the compound "aldehyde" from the Latin words translated as al(cohol) dehyd(rogenated). The formation of acetaldehyde by the addition of water [7732-18-5] to acetylene [74-86-2] was observed by Kutscherow] in 1881. 

Mercaptals, CH2CH(SR)2, are formed in a like manner by the addition of mercaptans. The formation of acetals by noncatalytic vapor-phase reactions of acetaldehyde and various alcohols at 35°C has been reported (67). Butadiene [106-99-0] can be made by the reaction of acetaldehyde and ethyl alcohol at temperatures above 300°C over a tantala—siUca catalyst (68). Aldol and crotonaldehyde are beheved to be intermediates. Butyl acetate [123-86-4] has been prepared by the catalytic reaction of acetaldehyde with 1-butanol [71-36-3] at 300°C (69). 

Miscellaneous Reactions. Sodium bisulfite adds to acetaldehyde to form a white crystalline addition compound, insoluble in ethyl alcohol and ether. This bisulfite addition compound is frequendy used to isolate and purify acetaldehyde, which may be regenerated with dilute acid. Hydrocyanic acid adds to acetaldehyde in the presence of an alkaU catalyst to form cyanohydrin the cyanohydrin may also be prepared from sodium cyanide and the bisulfite addition compound. Acrylonittile [107-13-1] (qv) can be made from acetaldehyde and hydrocyanic acid by heating the cyanohydrin that is formed to 600—700°C (77). Alanine [302-72-7] can be prepared by the reaction of an ammonium salt and an alkaU metal cyanide with acetaldehyde this is a general method for the preparation of a-amino acids called the Strecker amino acids synthesis. Grignard reagents add readily to acetaldehyde, the final product being a secondary alcohol. Thioacetaldehyde [2765-04-0] is formed by reaction of acetaldehyde with hydrogen sulfide thioacetaldehyde polymerizes readily to the trimer. 

Dibromoacetic acid [631-64-1] (Br2CHCOOH), mol wt 217.8, C2H2Br202, mp 48°C, bp 232—234°C (decomposition), is soluble in water and ethyl alcohol. It is prepared by adding bromine to boiling acetic acid, or by oxidi2ing tribromoethene [598-16-3] with peracetic acid. 

Tribromoacetic acid [75-96-7] (Br CCOOH), mol wt 296.74, C2HBr302, mp 135°C bp 245°C (decomposition), is soluble in water, ethyl alcohol, and diethyl ether. This acid is relatively unstable to hydrolytic conditions and can be decomposed to bromoform in boiling water. Tribromoacetic acid can be prepared by the oxidation of bromal [115-17-3] or perbromoethene [79-28-7] with fuming nitric acid and by treating an aqueous solution of malonic acid with bromine. 

Diiodoacetic acid [598-89-0] (I2CHCOOH), mol wt 311.85, C2H2I2O2, mp 110°C, occurs as white needles and is soluble in water, ethyl alcohol, and ben2ene. It has been prepared by heating diiodomaleic acid with water (61) and by treating malonic acid with iodic acid in a boiling water solution (62). 

---