Surfactant-free emulsion polymerization

Chem. Descrip. Phosphate ester, free acid Ionic Nature Anionic Uses Emulsion polymerization surfactant Regulatory FDA compliance... 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

Polychlorotrifluoroethylene (PCTFE) is ordinarily prepared by emulsion polymerization. A polymer suitable for thermal processing requires coagulation, extensive washing, and postpolymerization workup. Coagulation to provide a filterable and washable solid is a slow, difficult process and removal of surfactant is an important part of it. Complete removal may be extremely difficult depending on the extent of adsorption to the polymer particles. Consequently we set out to develop a suspension polymerization process, which would be surfactant-free and afford an easily isolated product requiring a minimum of postreaction workup. 

An intermediate polymerization technique between emulsion polymerization and suspension polymerization has been described. Here, the monomers are first dispersed in water containing a small amount of surfactant and a high molecular weight alcohol to form very small droplets of monomer. The polymerization is effected with a water-soluble free radical initiator, such as potassium per-oxydisulfate (4). 

Emulsion Polymerization. Poly(vinyl acetate)-based emulsion polymers are produced by the polymerization of an emulsified monomer through free-radicals generated by an initiator system. An emulsion recipe, in general. contains monomer, water, protective colloid or surfactant, initiator, buffer, and perhaps a molecular weight regulator. 

The emulsion polymerization methodology is one of the most important commercial processes. The simplest system for an emulsion (co)polymerization consists of water-insoluble monomers, surfactants in a concentration above the CMC, and a water-soluble initiator, when all these species are placed in water. Initially, the system is emulsified. This results in the formation of thermodynamically stable micelles or microemulsions built up from monomer (nano)droplets stabilized by surfactants. The system is then agitated, e.g., by heating it. This leads to thermal decomposition of the initiator and free-radical polymerization starts [85]. Here, we will consider a somewhat unusual scenario, when a surfactant behaves as a polymerizing comonomer [25,86]. 

The emulsion polymerization process involves the polymerization of liquid monomers that are dispersed in an aqueous surfactant micelle-containing solution. The monomers are solubilized in the surfactant micelles. A water-soluble initiator catalyst, such as sodium persulfate, is added to the aqueous phase. The free radicals generated cause the dispersed monomers to react to produce polymer molecules within the micellar environment. The surfactant plays an additional role in stabilizing dispersion of the produced polymer particles. Thus, the surfactants used both provide micelles to house the monomers and macroradicals, and also stabilize the produced polymer particles [193,790], Anionic surfactants, such as dodecylbenzene sulfonates, are commonly used to provide electrostatic stabilization [193], These tend to cause production of polymer particles having diameters of about 0.1-0.3 pm, whereas when steric stabilization is provided by, for example, graft copolymers, then diameters of about 0.1-10 pm tend to be produced [790,791]. 

Emulsion polymerization requires the use of free radical initiators, fluorinated surfactants, and often chain transfer agents. The polymer isolated from the reaction vessel consists of agglomerated spherical particles ranging in diameter from 0.2 to 0.5 jm.56 It is then dried and supplied as a free-flowing powder or as pellets, depending on the intended use. If very pure PVDF is required, the polymer is rinsed before the final drying to eliminate any impurities such as residual initiator and surfactants.57... 

Emulsion polymerization is a free radical initiated chain polymerization in which a monomer or a mixture of monomers is polymerized in aqueous solution of a surfactant to form a product, known as a latex. The most important feature of emulsion polymerization is its heterogeneity from the beginning to the end of the polymerization, to yield in a batch process submicron-sized polymeric particles, often of excellent monodispersity. The main ingredients for conducting... 

The key feature of Inisurfs is their surfactant behavior. They form micelles and are adsorbed at interfaces, and as such they are characterized by a critical micelle concentration (CMC) and an area/molecule in the adsorbed state. This influences both the decomposition behavior and the radical efficiency, which are much lower than those for conventional, low molecular weight initiators. Tauer and Kosmella [4] have observed that in the emulsion polymerization of styrene, using an Inisurf concentration above the CMC resulted in an increase in the rate constant of the production of free radicals. This was attributed to micellar catalysis effects as described, for example, by Rieger [5]. Conversely, if the Inisurf concentration was below the CMC the rate constant of the production of free radicals decreased with an increase in the Inisurf concentration, which was attributed to enhanced radical recombination. Also note that a similar effect of the dependence of initiator efficiency on concentration was reported by Van Hook and Tobolsky for azobisisobutyronitrile (AIBN) [6]. 

Emulsion polymerization—Free-radical polymerization carried out in micelles suspended in water. Ingredients include a surfactant (detergent) to form the micelles, a monomer that is not very soluble in water, and an initiator. The product consists of small particles of polymer suspended in water called a latex. ... 

One of the most important parameters in the S-E theory is the rate coefficient for radical entry. When a water-soluble initiator such as potassium persulfate (KPS) is used in emulsion polymerization, the initiating free radicals are generated entirely in the aqueous phase. Since the polymerization proceeds exclusively inside the polymer particles, the free radical activity must be transferred from the aqueous phase into the interiors of the polymer particles, which are the major loci of polymerization. Radical entry is defined as the transfer of free radical activity from the aqueous phase into the interiors of the polymer particles, whatever the mechanism is. It is beheved that the radical entry event consists of several chemical and physical steps. In order for an initiator-derived radical to enter a particle, it must first become hydrophobic by the addition of several monomer units in the aqueous phase. The hydrophobic ohgomer radical produced in this way arrives at the surface of a polymer particle by molecular diffusion. It can then diffuse (enter) into the polymer particle, or its radical activity can be transferred into the polymer particle via a propagation reaction at its penetrated active site with monomer in the particle surface layer, while it stays adsorbed on the particle surface. A number of entry models have been proposed (1) the surfactant displacement model (2) the colhsional model (3) the diffusion-controlled model (4) the colloidal entry model, and (5) the propagation-controlled model. The dependence of each entry model on particle diameter is shown in Table 1 [12]. 

In order to gain evidence for interfacial initiation, the redox initiator system was compared with a water-soluble initiator (VA-044) in terms of the emulsion polymerization behavior of butyl acrylate (BA)/[2-(methacryloyoxy)ethyl] trimethyl ammonium chloride (MAETAC). It was found that for the water-soluble initiator system, only homopoly(MAETAC) was formed and BA did not polymerize at all. In the case of VA-044, it was suggested that it may be difficult for polymeric free radicals in the aqueous phase to penetrate the viscous surfactant layer to initiate the polymerization of the BA monomer. On the other hand, it has also been found that BA could be rapidly polymerized under the same conditions if VA-044 is replaced with CHP/TEPA, indicating that radicals are formed in the interface, where they do not need to penetrate through viscous surfactant layer. 

Candau and co-workers were the first to address the issue of particle nu-cleation for the polymerization of AM [13, 14] in an inverse microemulsion stabilized by AOT. They found that the particle size of the final microlatex (d 20-40 nm) was much larger than that of the initial monomer-swollen droplets (d 5-10 nm). Moreover, each latex particle formed contained only one polymer chain on average. It is believed that nucleation of the polymer particle occurs for only a small fraction of the final nucleated droplets. The non-nucleated droplets also serve as monomer for the growing particles either by diffusion through the continuous phase and/or by collisions between droplets. But the enormous number of non-nucleated droplets means that some of the primary free radicals continuously generated in the system will still be captured by non-nucleated droplets. This means that polymer particle nucleation is a continuous process [ 14]. Consequently, each latex particle receives only one free radical, resulting in the formation of only one polymer chain. This is in contrast to the large number of polymer chains formed in each latex particle in conventional emulsion polymerization, which needs a much smaller amount of surfactant compared to microemulsion polymerization. 

---