Dimethyl acetonitrile

Besides the well-known lower basicity of ethanol, these data illustrate the greater acidity of benzoxazolium compared with benzothiazolium. The relative pK. values of the quaternary salts obtained in acetonitrile when treated with tetrabutylammonium hydroxide are 18.3 and 17.6, respectively (25). Those of 2-methyl 4-phenyl thiazolium and 2.4-dimethyl thiazolium are 20.5 and 21.8 under the same conditions (25). 

Trifluoromethanesulfonic acid is miscible in all proportions with water and is soluble in many polar organic solvents such as dimethylformamide, dimethyl sulfoxide, and acetonitrile. In addition, it is soluble in alcohols, ketones, ethers, and esters, but these generally are not suitably inert solvents. The acid reacts with ethyl ether to give a colorless, Hquid oxonium complex, which on further heating gives the ethyl ester and ethylene. Reaction with ethanol gives the ester, but in addition dehydration and ether formation occurs. 

Economic considerations in the 1990s favor recovering butadiene from by-products in the manufacture of ethylene. Butadiene is a by-product in the C4 streams from the cracking process. Depending on the feedstocks used in the production of ethylene, the yield of butadiene varies. Eor use in polymerization, the butadiene must be purified to 994-%. Cmde butadiene is separated from C and C components by distillation. Separation of butadiene from other C constituents is accomplished by salt complexing/solvent extraction. Among the solvents used commercially are acetonitrile, dimethyl acetamide, dimethylform amide, and /V-methylpyrrolidinone (13). Based on the available cmde C streams, the worldwide forecasted production is as follows 1995, 6,712,000 1996, 6,939,000 1997, 7,166,000 and 1998, 7,483,000 metric tons (14). As of January 1996, the 1995 actual total was 6,637,000 t. 

Acetonitrile oxide was generated from 3,4-dimethylfuroxan oxide by flash vacuum pyrolysis and trapped at -40 °C where its and NMR spectra were examined. Warming to room temperature in the presence of propane produced 3,5-dimethyl-2-isoxazoline (Scheme 108) (79TL2443). The oxide could also be generated by photolysis of furoxan (68CC977). 

Dried with Linde type 5A molecular sieves or Na2S04 and fractionally distd at reduced pressure. Alternatively, it was refluxed with, and distd from, BaO. Also purified by fractional crystn from the melt and distd from zinc dust. Converted to its phosphate (m 135°) or picrate (m 223°), which were purified by crystn and the free base recovered and distd. [Packer, Vaughn and Wong J Am Chem Soc 80 905 1958.] The procedure for purifying via the picrate comprises the addition of quinoline to picric acid dissolved in the minimum volume of 95% EtOH to yield yellow crystals which are washed with EtOH and air dried before recrystn from acetonitrile. The crystals are dissolved in dimethyl sulfoxide (previously dried over 4A molecular sieves) and passed through a basic alumina column, on which picric acid is adsorbed. The free base in the effluent is extracted with n-pentane and distd under vacuum. Traces of solvent are removed by vapour phase chromatography. [Mooman and Anton J Phys Chem 80 2243 1976.]... 

NOTE - Petrochemical plants also generate significant amounts of solid wastes and sludges, some of which may be considered hazardous because of the presence of toxic organics and heavy metals. Spent caustic and other hazardous wastes may be generated in significant quantities examples are distillation residues associated with units handling acetaldehyde, acetonitrile, benzyl chloride, carbon tetrachloride, cumene, phthallic anhydride, nitrobenzene, methyl ethyl pyridine, toluene diisocyanate, trichloroethane, trichloroethylene, perchloro-ethylene, aniline, chlorobenzenes, dimethyl hydrazine, ethylene dibromide, toluenediamine, epichlorohydrin, ethyl chloride, ethylene dichloride, and vinyl chloride. 

Dehydrochlorination of bis(tnfluoromethylthio)acetyl chloride with calcium oxide gives bis(trifluoromethylthio)ketene [5] (equation 6) Elimination of hydrogen chloride or hydrogen bromide by means of tetrabutylammonium or potassium fluoride from vinylic chlorides or bromides leads to acetylenes or allenes [6 (equation 7) Addition of dicyclohexyl-18-crown-6 ether raises the yields of potassium fluoride-promoted elimination of hydrogen bromide from (Z)-P-bromo-p-ni-trostyrene in acetonitrile from 0 to 53-71 % In dimethyl formamide, yields increase from 28-35% to 58-68%... 

In the case of enamines derived from aldehydes a cycloaddition to give a cyclobutane occurs (48-50). Thus the enamine (16) reacted with methyl acrylate in acetonitrile to give a 91 % yield of methyl 2-dimethylamino-3,3-dimethylcyclobutane carboxylate (56). Similarly, treatment of (16) with diethylmaleate at 170° gave a 70% yield of diethyl 4-dimethylamino-3,3-dimethyl-l,2-cyclobutanedicarboxylate (57), and 16 and acrylonitrile gave a 65% yield of 2-dimethylamino-3,3-dimethylcyclobutanecarbonitrile (58). 

The importance of the solvent, in many cases an excess of the quatemizing reagent, in the formation of heterocyclic salts was recognized early. The function of dielectric constants and other more detailed influences on quatemization are dealt with in Section VI, but a consideration of the subject from a preparative standpoint is presented here. Methanol and ethanol are used frequently as solvents, and acetone,chloroform, acetonitrile, nitrobenzene, and dimethyl-formamide have been used successfully. The last two solvents were among those considered by Coleman and Fuoss in their search for a suitable solvent for kinetic experiments both solvents gave rise to side reactions when used for the reaction of pyridine with i-butyl bromide. Their observation with nitrobenzene is unexpected, and no other workers have reported difficulties. However, tetramethylene sulfone, 2,4-dimethylsulfolane, ethylene and propylene carbonates, and salicylaldehyde were satisfactory, giving relatively rapid reactions and clean products. Ethylene dichloride, used quite frequently for Friedel-Crafts reactions, would be expected to be a useful solvent but has only recently been used for quatemization reactions. ... 

Abbreviations Aik, alkyl AN, acetonitrile Ar, aryl Bu, butyl cod, 1,5-cyclooctadiene Cp, cy-clopentadienyl Cp , pentamethylcyclopentadienyl Cy, cyclohexyl dppm, diphenylphosphinome-thane dpme, Ph2PC2H4PMe2 Et, ethyl fod, 6,6,7,7,8,8,8-heptafluoro-2,2-dimethyl-3,5-octane-dionate HOMO, highest occupied molecular orbital LUMO, lowest unoccupied molecular orbital Me, methyl MO, molecular orbital nbd, norbornadiene Nuc, nucleophile OTf, triflate Ph, phenyl Pr, propyl py, pyridine THE, tetrahydrofuran TMEDA V,V,M,M-tetramethylethylenediamine. 

Kinetic studies have been carried out on the displacement reactions of various chloroazanaphthalenes with ethoxide ions and piperi-dine. - 2-Chloroquinoxaline is even more reactive than 2-chloro-quinazoline, thus demonstrating the powerfully electrophilic nature of the -carbon atoms in the quinoxaline nucleus. The ease of displacement of a-chlorine in the quinoxaline series is of preparative value thus, 2-alkoxy-, 2-amino-, - 2-raethylamino-, 2-dimethyl-amino-,2-benzylamino-, 2-mercapto-quinoxalines are all readily prepared from 2-chloroquinoxaline. The anions derived from substituted acetonitriles have also been used to displace chloride ion from 2-chloroquinoxaline, ... 

This compound may be produced by reacting o-chlorobenzophenone with acetonitrile in the presence of sodium amide or another strongly basic condensing agent, to form the nitrile of /3-phenyl-/3-o-chlorophenyl-hydracrylic acid, which is then hydrogenated to yield Tphenyl-l-o-chlorophenyl-S-aminopropanol-l. The latter intermediate compound is subsequently dimethylated with an agent such as methyl sulfate to provide the desired end product l-o-chlorophenyl-Tphenyl-S-dimethylaminopropanol. 

The organic fractions are combined and washed successively with N,N-dimethyl-1,3-propane-diamine, dilute hydrochloric acid, saturated sodium bicarbonate solution and saturated sodium chloride solution. The organic fraction is dried over anhydrous magnesium sulfate. The solvent is then evaporated off. Upon trituration of the residue with methanol, a solid crystallizes, 5-(p-toluovl)-1 -methvlpvrrole-2-acetonitrile, which is removed by filtration and purified by recrystallization from benzene. 

To 5 grams of N,N -bis[1-methyi-3-(2,2,6-trimethylcyclohexyl)propyl]-N,N -dimethyl-1,6-hexanediamine dissolved in 100 ml of methanol, at 4°C, were added 100 ml methanol containing 10 grams of methyl chloride. The solution was heated in a closed vessel at 60°C for 15 hours. The colorless solution was concentrated and the resulting white solid crystallized from ethanol-acetonitrile-ether to obtain N,N -bis[1-methyl-3-(2,2,6-trimethylcyclo-hexyOpropyl] -N,N -dimethyl-1,6-hexanediamine bis(methochloride) hemihydrate. 

Similarly, photolysis of l-(2-azidophenyl)-l/f-pyrazole in acetonitrile in the presence of dipropylamine affords AfN-dipropyl-7-(lF/-pyrazol-l-yl)-3//-azepin-2-amine in low yield (4%).192 Surprisingly, however, photolysis of the corresponding 1-(2-azidophenyl)-3,5-dimethyl-l//-pyrazole (84) in cyclohexane in the presence of the base yields 85 which, on the basis of H NMR spectroscopic evidence, has been formulated as a rare example of a stable 2 H-azepine. 

Iodine azide, generated in situ from an excess of sodium azide and iodine monochloride in acetonitrile, adds to ethyl l//-azepine-l-carboxylate at the C4 — C5 and C2 —C3 positions to yield a 10 1 mixture of the rw-diazidodihydro-l//-azepines 1 and 2, respectively.278 The as stereochemistry of the products is thought to be the result of initial trans addition of the iodine azide followed by an SN2 azido-deiodination. The diazides were isolated and their stereochemistry determined by conversion to their bis-l,3-dipolar cycloadducts with dimethyl acetylene-dicarboxylate. 

Occasionally, these thermally induced reactions give rise to complex mixtures of products and hence are not of any great preparative value. For example, 1-mcthylindolc with dimethyl acetylenedicarboxylate in acetonitrile yields seven products including the 1-benzazepine 8 (14%), the 1-methyl derivatives of the cis- and /rwK-indolylacrylates 3. a [4 + 2] cycloadduct of the 1-benzazcpinc with the alkyne dicster (see Section 3.2.2.5.3.), and dimethyl l-mcthyl-2-(l-methylindol-3-yl)-2,3-dihydro-l //-l-benzazepinc-3,4-dicarboxylate (9).21 This last product, which is the major product if the cycloaddition is carried out in acetonitrile containing trace amounts of water,21 has been obtained earlier.143 but was incorrectly formulated. 

In the presence of a catalytic amount of concentrated hydrochloric acid, dimethyl 1 -methyl-1 H-l-benzazepine-3,4-dicarboxylate (1) undergoes addition of 1-methylindole, probably via initial protonation of the enaminic 3-position of the benzazepine ring, to give the indolyldihydrobenz-azepine 2.21 In fact, adduct 2 is the major product from the reaction of 1-mcthylindole with dimethyl acetylenedicarboxylate in acetonitrile. Similar adducts are obtained with indole. 

The configuration of the adduct with dimethyl acetylenedicarboxylate depends on the nature of the solvent used protic solvents, such as methanol or ethanol (but not tert-butyl alcohol), favor formation of (Z)-25a, whereas in nonprotic solvents, such as benzene, chloroform or acetonitrile, ( )-25a is the major product. 

While water has been used as a solvent more than any other media, nonaqueous solvents [e.g., acetonitrile, propylene carbonate, dimethylformamide (DMF), dimethyl sulfoxide (DMSO), or methanol] have also frequently been used. Mixed solvents may also be considered for certain applications. Double-distilled water is adequate for most work in aqueous media. Triple-distilled water is often required when trace (stripping) analysis is concerned. Organic solvents often require drying or purification procedures. These and other solvent-related considerations have been reviewed by Mann (3). 

Potassium or lithium derivatives of ethyl acetate, dimethyl acetamide, acetonitrile, acetophenone, pinacolone and (trimethylsilyl)acetylene are known to undergo conjugate addition to 3-(t-butyldimethylsiloxy)-1 -cyclohexenyl t-butyl sulfone 328. The resulting a-sulfonyl carbanions 329 can be trapped stereospecifically by electrophiles such as water and methyl iodide417. When the nucleophile was an sp3-hybridized primary anion (Nu = CH2Y), the resulting product was mainly 330, while in the reaction with (trimethylsilyl)acetylide anion the main product was 331. 

---