Cresol reaction

Carter, W.P.L., Winer, A.M., Pitts, Jr., J.N. (1981) Major atmospheric sink for phenol and the cresols. Reaction with the nitrate radical. Environ. Sci. Technol. 15, 829-831. 

The 2,6-di-tertbutyl-p-cresol reaction also produces fluorescent products with certain corticosteroids, which allows the development of fluorimetric methods for their determination. These will be discussed in a subsequent section. 

Thiobis(2-methyl-6-butylphenol) Thiodiethylene bis(3,5-di-tert-butyl-4-hydroxycinnamate) 4,6-Bis(octylthiomethyl)-o-cresol Reaction product of nonylphenol, dodecanethiol, and formaldehyde... 

Figure ll-E-3. Arrhenius plot of the rate coefficients for the OH + -cresol reaction. 

The rate coefficients for the 03-m-cresol reaction were obtained by Atkinson et al. (1978a, 1982d) and are presented in table II-E-7. The determination of Atkinson et al. (1978a) is considered to be an upper limit for the reason mentioned for the reaction of O3 with o-cresol. The recommended value is based on the study of Atkinson et al. 

MCPA, l-methyl-A-chlorophenoxyacetic acid, Methoxone, CgH ClOj. Made by chlorination of o-cresol followed by reaction with chloroethanoic acid. While crystals, m.p. 118-119 C. As usually obtained, crude MCPA contains both 4- (60%) and 6- (40%) chloro-isomers, and is a light brown solid. Selective weedkiller. 

The solution must be strongly acid in order to avoid the coupbng reaction between the undecomposed diazonium salt and the phenol (see under Azo Dyes). For the preparation of phenol and the cresols, the aqueous solution of the diazonium compound is warmed to about 50° at higher temperatures the reaction may become unduly vigorous and lead to appreciable quantities of tarry compounds... 

Under the same conditions the even more reactive compounds 1,6-dimethylnaphthalene, phenol, and wt-cresol were nitrated very rapidly by an autocatalytic process [nitrous acid being generated in the way already discussed ( 4.3.3)]. However, by adding urea to the solutions the autocatalytic reaction could be suppressed, and 1,6-dimethyl-naphthalene and phenol were found to be nitrated about 700 times faster than benzene. Again, the barrier of the encounter rate of reaction with nitronium ions was broken, and the occurrence of nitration by the special mechanism, via nitrosation, demonstrated. 

Epoxy novolac resins are produced by glycidation of the low-molecular-weight reaction products of phenol (or cresol) with formaldehyde. Highly cross-linked systems are formed that have superior performance at elevated temperatures. 

Positive-Tone Photoresists based on Dissolution Inhibition by Diazonaphthoquinones. The intrinsic limitations of bis-azide—cycHzed mbber resist systems led the semiconductor industry to shift to a class of imaging materials based on diazonaphthoquinone (DNQ) photosensitizers. Both the chemistry and the imaging mechanism of these resists (Fig. 10) differ in fundamental ways from those described thus far (23). The DNQ acts as a dissolution inhibitor for the matrix resin, a low molecular weight condensation product of formaldehyde and cresol isomers known as novolac (24). The phenoHc stmcture renders the novolac polymer weakly acidic, and readily soluble in aqueous alkaline solutions. In admixture with an appropriate DNQ the polymer s dissolution rate is sharply decreased. Photolysis causes the DNQ to undergo a multistep reaction sequence, ultimately forming a base-soluble carboxyHc acid which does not inhibit film dissolution. Immersion of a pattemwise-exposed film of the resist in an aqueous solution of hydroxide ion leads to rapid dissolution of the exposed areas and only very slow dissolution of unexposed regions. In contrast with crosslinking resists, the film solubiHty is controUed by chemical and polarity differences rather than molecular size. 

Triaryl phosphates are produced from the corresponding phenols (usually mixtures) by reaction with phosphoms oxychloride, usually in the presence of a catalyst (94—96). They are subsequently distilled and usually washed with aqueous bases to the desired level of purity. Tricresyl phosphate was originally made from petroleum-derived or coal-tar-derived cresyflc acids, ie, cresols, variously admixed with phenol and xylenols. Discovery of the toxicity of the ortho-cresyl isomers led manufacturers to select cresols having very Httle ortho-isomer. 

An alternative process (97) for direct esterification of cresols using phosphoric acid, a slow reaction, was developed in Israel, where phosphoms oxychloride is not locally available. 

Polymer-type antioxidants have been prepared by Eriedel-Crafts reaction of -cresol andp- and/or y -chloromethylstyrene in the presence of boron trifluoride-etherate (198). The oligomeric product resulting from the alkylation of phenyl-a-naphthylamine using C12—15 propylene oligomer in the presence of AlCl or activated white clays is used as an antioxidant additive for lubricating oils (199). 

The wide variety of ketomethylene and amino ketone monomers that could be synthesized, and the abiUty of the quinoline-forming reaction to generate high molar mass polymers under relatively mild conditions, allow the synthesis of a series of polyquinolines with a wide stmctural variety. Thus polyquinolines with a range of chain stiffness from a semirigid chain to rod-like macromolecules have been synthesized. Polyquinolines are most often prepared by solution polymerization of bis(i9-amino aryl ketone) and bis (ketomethylene) monomers, where R = H or C H, in y -cresol with di-y -cresyl phosphate at 135—140°C for a period of 24—48 h (92). 

Oxidation inhibitors function by intermpting the hydroperoxide chain reaction. At temperatures up to ca 120°C, di-Z fZ-butyl- -cresol, 2-naphthol,... 

Triaryl phosphates are produced by reaction of phosphoms oxychloride with phenoHc compounds at 100—200°C with magnesium or aluminum chloride catalyst. Past use of cresols and xylenols from coal tar or petroleum is replaced for lower toxicity and cost by synthetic phenoHcs, primarily isopropyl phenol, /-butyl phenol, and phenol itself A range of viscosities is achieved by selection and proportioning of the phenols and their isomers used for the starting material. 

Nitromersol/777-j5 , y (4) and mercurophen [52486-78-9] (5) are prepared by the same mercuration reaction as phenyhnercuric acetate, only 4-nitro-(9-cresol and o-nitrophenol are used, respectively, iastead of benzene. The second step is reaction with sodium hydroxide to form the anhydride or sodium salt, respectively. 

Significant quantities of the diphenoquinone are also produced if the ortho substituents are methoxy groups (36). Phenols with less than two ortho substituents produce branched and colored products from the reactions that occur at the open ortho sites. It is possible to minimize such side reactions in the case of o-cresol oxidation by using a bulky ligand on the copper catalyst to block the open ortho position (38). 

Methylphenol. This phenol, commonly known as o-cresol, is produced synthetically by the gas phase alkylation of phenol with methanol using modified alumina catalysis or it may be recovered from naturally occurring petroleum streams and coal tars. Most is produced synthetically. Reaction of phenol with methanol using modified zeoHte catalysts is a concerted dehydration of the methanol and alkylation of the aromatic ring. 2-Methylphenol [95-48-7] is available in 55-gal dmms (208-L) and in bulk quantities in tank wagons and railcars. 

Methylphenol is converted to 6-/ f2 -butyl-2-methylphenol [2219-82-1] by alkylation with isobutylene under aluminum catalysis. A number of phenoHc anti-oxidants used to stabilize mbber and plastics against thermal oxidative degradation are based on this compound. The condensation of 6-/ f2 -butyl-2-methylphenol with formaldehyde yields 4,4 -methylenebis(2-methyl-6-/ f2 butylphenol) [96-65-17, reaction with sulfur dichloride yields 4,4 -thiobis(2-methyl-6-/ f2 butylphenol) [96-66-2] and reaction with methyl acrylate under base catalysis yields the corresponding hydrocinnamate. Transesterification of the hydrocinnamate with triethylene glycol yields triethylene glycol-bis[3-(3-/ f2 -butyl-5-methyl-4-hydroxyphenyl)propionate] [36443-68-2] (39). 2-Methylphenol is also a component of cresyHc acids, blends of phenol, cresols, and xylenols. CresyHc acids are used as solvents in a number of coating appHcations (see Table 3). 

Methylphenol. y -Cresol is produced synthetically from toluene. Toluene is chlorinated and the resulting chlorotoluene is hydrolyzed to a mixture of methylphenols. Purification by distillation gives a mixture of 3-methylphenol and 4-methylphenol since they have nearly identical boiling points. Reaction of this mixture with isobutylene under acid catalysis forms 2,6-di-/ f2 -butyl-4-methylphenol and 2,4-di-/ f2 -butyl-5-methylphenol, which can then be separated by fractional distillation and debutylated to give the corresponding 3- and 4-methylphenols. A mixture of 3- and 4-methylphenols is also derived from petroleum cmde and coal tars. 

Cresols can be made from propylene by reaction with toluene to produce cumene (111). 

Sulfation by sulfamic acid has been used ia the preparation of detergents from dodecyl, oleyl, and other higher alcohols. It is also used ia sulfating phenols and phenol—ethylene oxide condensation products. Secondary alcohols react ia the presence of an amide catalyst, eg, acetamide or urea (24). Pyridine has also been used. Tertiary alcohols do not react. Reactions with phenols yield phenyl ammonium sulfates. These reactions iaclude those of naphthols, cresol, anisole, anethole, pyrocatechol, and hydroquinone. Ammonium aryl sulfates are formed as iatermediates and sulfonates are formed by subsequent rearrangement (25,26). 

---