Constructive design

Protective Construction Design Manual 1984—1989, AppHed Research Assoc., Albuquerque, N. Mex. 

Subsection A This subsection contains the general requirements applicable to all materials and methods of construction. Design temperature and pressure are defined here, and the loadings to be considered in design are specified. For stress failure and yielding, this section of the code uses the maximum-stress theory of failure as its criterion. 

The primaiy purpose of materials selection is to provide the optimum equipment for a process application in terms of materials of construction, design, and corrosion-control measures. Optimum here means that which comprises the best combination of cost, life, safety, and reliability. 

The above are the more obvious constructional, design and safety features for a switchgear or a controlgear assembly. For more details and additional requirements refer to lEC 60439-1 for LT, lEC 60298 and lEC 60694 for FIT and ANSI-C-37/20C, common for LT and FIT switchgear and controlgear assemblies. 

Type tests are conducted on the first enclosure of each voltage, current rating and fault level to demonstrate compliance with electrical and constructional design parameters. The tests provide a standard reference for any subsequent enclosure with similar ratings and constructional details. The following tests may be conducted to demonstrate verification of the following ... 

Bayer, C. W., and Black, M. S. (1988a) Indoor Air Quality Evaluations of Three Office Buildings Two of Conventional Construction Designs and One of a Special Design to Reduce Indoor Air Contaminants. Georgia Institute of Technology, Athens, GA. 

Adequate capacity and construction Designed to hold spillage Properly lit and ventilated Fire- and frost-resistant... 

The factors Uiat enter into tlie design of vessels include type of material, configuration, inetliod of construction, design stresses, and tliickness of Uie metal. As with any equipment, design pressures and temperatures should take into consideration Uie most severe combination of conditions anticipated. Vessels must be completely drainable. Liners and wear plates may be required to prevent corrosion. 

Anlage, /. laying on, etc. (see anlegen) establishment, plant unit installation, e iuip-ment construction design outline ar-... 

Bau, m. structure constitution construction building make cultivation, -art, /. construction, design, style, -breite, /. over-all breadth. 

Bau-form,/. style of construction, design, -holz, n. timber, -ingenieur, m. structural engineer, -kunst, /. architecture, (art of) bmlding or construction. -Iknge, /. over-all length. 

RGB—Includes all classes of construction/design and are identical shell diameter (inside) not exceeding 60 in., and maximum design pressure of 3,000 psi. 

Lyons, R.E., Lesieur, E., Kim, M., Wong, D., Brownlee, A., Pearson, R., and Elvin, C., The development of synthetic genes encoding repetitive resilin-like polypeptides Construct design, bacterial expression and rapid purification. Protein Eng. Design Select., 20(1), 25-32, 2007. 

Podhorssky, M. and Krips, H. Heat Exchangers A Practical Approach to Mechanical Construction, Design, and Calculations (Begell House, 1998). 

Basis of chart Floating head Carbon steel construction Design pressure, 150 psi. 

Storage requirements Suitable siting Adequate capacity and construction Designed to hold spillage Properly lit and ventilated Fire- and frost-resistant Designed so that containers can be safely stacked and moved Clearly marked Kept locked except when in use... 

The cell bank s construction design is normally two tiered, consisting of a master cell bank and a working cell bank (Figure 5.6). The master cell bank is constructed first, directly from a culture of the newly constructed production cell line. It can consist of several hundred individually stored ampoules. 

An alternative approach to constructing designs for estimating second-order models is to consider building a design from those constructed for the first-order model. In Section 2.2.1, we discussed the use of fractional factorial designs to estimate the coefficients of the first-order model. It was noted that a fractional factorial design of resolution V would yield... 

As with most collections of data, the price data correlated here exhibit a certain amount of scatter. This is due in part to the incomplete characterizations in terms of which the correlations are made, but also to variations among manufacturers, qualities of construction, design differences, market situations, and other factors. Accordingly, the accuracy of the correlations cannot be claimed to be better than 25% or so. 

Methanator Plant M-one construction, design, and operating conditions... 

The manufacturing method and distribution system also have a close relation with the construction design of facilities and equipment. 

Nitric Acid Tank- Design Data Design tank capacity Design temperature Design pressure Working pressure Nitric acid density Material of construction Design tensile strength Joint efficiency... 

Total column height Internal diameter Operating pressure Operating temperatures Number of sieve trays Material of construction Design stress... 

---