Condition dependent

Level of enforcement of the incompressibility condition depends on the magnitude of the penalty parameter. If this parameter is chosen to be excessively large then the working equations of the scheme will be dominated by the incompressibility constraint and may become singular. On the other hand, if the selected penalty parameter is too small then the mass conservation will not be assured. In non-Newtonian flow problems, where shear-dependent viscosity varies locally, to enforce the continuity at the right level it is necessary to maintain a balance between the viscosity and the penalty parameter. To achieve this the penalty parameter should be related to the viscosity as A = Xorj (Nakazawa et al, 1982) where Ao is a large dimensionless parameter and tj is the local viscosity. The recommended value for Ao in typical polymer flow problems is about 10. ... 

Reaction conditions depend on the composition of the bauxite ore, and particularly on whether it contains primarily gibbsite, Al(OH)2, or boehmite [1318-23-6] AlOOH. The dissolution process is conducted in large, stirred vessels or alternatively in a tubular reactor. The process originated as a batch process, but has been converted to a continuous one, using a series of stirred tank reactors or a tubular reactor. 

Reaction conditions depend on the reactants and usually involve acid or base catalysis. Examples of X include sulfate, acid sulfate, alkane- or arenesulfonate, chloride, bromide, hydroxyl, alkoxide, perchlorate, etc. RX can also be an alkyl orthoformate or alkyl carboxylate. The reaction of cycHc alkylating agents, eg, epoxides and a2iridines, with sodium or potassium salts of alkyl hydroperoxides also promotes formation of dialkyl peroxides (44,66). Olefinic alkylating agents include acycHc and cycHc olefinic hydrocarbons, vinyl and isopropenyl ethers, enamines, A[-vinylamides, vinyl sulfonates, divinyl sulfone, and a, P-unsaturated compounds, eg, methyl acrylate, mesityl oxide, acrylamide, and acrylonitrile (44,66). 

Emissions During Processing. During the production of flexible PVC products plasticizers are exposed for up to several minutes to temperatures of - ISO C. The exact conditions depend on the processing technique employed, but it is evident that the loss of plasticizer by evaporation and degradation can be significant. 

Acetone also reacts with diphenylamine, in the presence of acid, to form a variety of condition-dependent products (5). Excess amine and a small amount of strong acid catalyst at 100—150°C give 2,2-[4,4 -(dianilino)diphenyl]-propane [2980-26-9] (6). With a large amount of hydrochloric acid at 250°C in the presence of excess diphenylamine, the main product is 9,9-dimethylacridan [6267-02-3]. 

In the first case, if we had considered a safe line length of 250 km, this would become 500 km for a symmetrical line. Figure 24.18 illustrates such a condition. Depending upon the length and type of line, a line length compensation may be required. Most transmission lines are seen to be within permissible lengths and only a few may require such a compensation. Nevertheless, it may be worth reducing the phase displacement between E, and to less than 15° electrical, to further iinprove the quality and stability level of power transmission. 

Another view is given in Figure 3.1.2 (Berty 1979), to understand the inner workings of recycle reactors. Here the recycle reactor is represented as an ideal, isothermal, plug-flow, tubular reactor with external recycle. This view justifies the frequently used name loop reactor. As is customary for the calculation of performance for tubular reactors, the rate equations are integrated from initial to final conditions within the inner balance limit. This calculation represents an implicit problem since the initial conditions depend on the result because of the recycle stream. Therefore, repeated trial and error calculations are needed for recycle... 

Usage Numbers refer to usage for anaylsis of solid materials. 1 means Extensive 2 means medium 3 means not common. Trace capability Guide only. Often very maten al/conditions dependent. — means not used for trace components. 

Gastroenteritis Gastroenteritis is an acute inflammation of the lining of the stomach and intestines. Symptoms include anorexia, nausea, diarrhea, abdominal pain and weakness. Gastroenteritis has many causes, such as bacteria (food poisoning), viruses, parasites, consumption of irritating food or drink, as well as stress. Treatment for the condition depends on the underlying cause. 

Operator error probability under stressful conditions depends upon the time to complete a sequence of events. The total time available for limiting sequences was 7.9 hours which is the time to completely drain the cooling water basin. Sequence (6) required the most operator actions (11) was... 

Lower operating costs under many conditions, depending upon the type of water system used for comparison. 

Figure 12-22 is convenient for solving for the temperature rise fector for either polytropic or adiabatic conditions, depending upon whether k or n is used. 

Human occupants, electrical/electronic equipment and process plant all emit varying quantities of sensible and latent heat. Equally, these various elements require (or can tolerate) differing environmental conditions. Depending on these operational constraints, the need may well exist to provide natural (or powered) ventilation to maintain environmental conditions (temperature and/or humidity) consistent with the occupational/process requirements. 

That some silver does dissolve to form Ag+ can be verified experimentally by adding a little KI to the solution. Silver iodide has an even lower solubility than does silver chloride. The experiment shows that the amount of silver that dissolves is sufficient to cause a visible precipitate of Agl but not of AgCl. This places the Ag+ ion concentration below 10-10 M but above 10-17 M. Either of these concentrations is so small that we can consider our prediction for the standard state to be applicable here too—silver metal does not dissolve appreciably in 1 M HC1. In general, the question of whether a prediction based upon the standard state will apply to other conditions depends upon how large is the magnitude of °. If ° for the overall reaction is only one- or two-tenths volt (either positive or negative), then deviations from standard conditions may invalidate predictions that do not take into account these deviations. 

The operating pressures and shear rates in the extrusion process are considerably lower than they are in molding. As it exits the die, but not necessarily when it leaves the process, the material is in an essentially stress-free condition. Depending on the wall thickness of the material and the particular material, there is orientation of the plastic to a greater or lesser controllable degree. Thin walls produce higher orientation in materials such as PP, that is a highly crystalline polyolefin, and which orients much more than materials such as PVC. 

The resulting equations, arrived at by setting appropriate initial and boundary conditions (depending on the particular electrode), are given in Table 3-4. 

It was found that both the catalytic rates and the selectivity to the various products can be altered significantly (rate changes up to 250% were observed) and reversibly under NEMCA conditions. Depending on the product, electrophobic or electrophilic behaviour is observed as shown in Fig. 8.57. In addition to the selectivity modification due to the different effect on the rate of formation of each product, acetaldehyde, which is not produced under open circuit conditions is formed at negative overpotentials (Fig. 8.58). Enhancement factor A values up to 10 were observed in this complex system.59... 

The power input in stirred tanks can be calculated using the equation P = Ne pnM if the Newton number Ne, which at present still has to be determined by empirical means, is known. For stirred vessels with full reinforcement (bafQes, coils, see e.g. [20]), the only bioreactors of interest, this is a constant in the turbulent flow range Re = nd /v> 5000-10000, and in the non-aerated condition depends only on geometry (see e.g. [20]). In the aerated condition the Newton number is also influenced by the Froude number Fr = n d/g and the gas throughput number Q = q/nd (see e.g. [21-23]). 

The three-way catalyst and the NOx storage-reduction catalyst represent remarkably successful catalytic technology. The catalysts are unique in that they have to operate under a wide range of conditions, depending on type of use, personal driving style, local climate, etc. This in contrast to the usual situation in industry, where conditions are optimized and kept constant. 

SRB, a diverse group of anaerobic bacteria isolated from a variety of environments, use sulfate in the absence of oxygen as the terminal electron acceptor in respiration. During biofilm formation, if the aerobic respiration rate within a biofilm is greater than the oxygen diffusion rate, the metal/biofilm interface can become anaerobic and provide a niche for sulfide production by SRB. The critical thickness of the biofilm required to produce anaerobie conditions depends on the availability of oxygen and the rate of respiration. The corrosion rate of iron and copper alloys in the presence of hydrogen sulfide is accelerated by the formation of iron sulfide minerals that stimulate the cathodic reaction. 

The nature and intensity of the effect highly depend on the way toxic substances penetrate into the organism. Three main means of penetration are identified inhalation, skin contact, ingestion. Some penetration means are favoured under identical exposure conditions depending on the substance s properties. 

---