Available time

If retrofits and new installations consume the available time of these engineers, the potential for omission increases. Therefore, more time should be allowed for the work. 

The thinking interval is the difference between 30 second, and third tasks performe d minutes (the total available time) and the sum of a) the time Hues are success, broken liiu s... 

The PSM champion has decided to devote the first hour to a structured presentation, using the balance of available time for questions and answers. 

The fundamental requirement of an efffective outage plan is well-defined work orders for each task that must be performed during the available time interval. Too many plants fail to fully plan each of the tasks that are to be performed. Instead, they rely on a master schedule that defines the sequence of events that must occur in order to complete all of the tasks included in the scope of work. 

Avoiding product failures can depend, in part, on the ability to predict the performance of plastic materials and their shapes. With available time, the usual approach of product prototype and/or field-testing provides useful and reliable performance data when conducted properly. As an example designers continue to develop sophisticated computer methods for calculating stresses in complex structures. 

The design of a phytoremediation system is determined by several factors associated with the contaminants (type, concentration, and depth), the conditions at the site, the plants, the level of cleanup required and the available time. Extraction techniques have different design requirements than immobilization or degradation methods. Nevertheless, it is possible to specify a few design factors that are a part of most phytoremediation efforts. 

The study scope results form goals and is determined by financial resources of the ordering authority and the available time of the processor [5], The study scope describes the most important methodological choices, hypothesis and limits [35] that are described below. 

The traditional (Rosin, et al., 1932) mechanistic approach equates the time necessary for a particle to settle at a Stokes law velocity across the width of a cyclone s inlet duct, to the available residence time of the carrier gas stream in its number of spiral traverses within the barrel. With reference to Fig. 1, this permits solving for the smallest particle size able to cross the entire width and reach the wall in the available time. 

This step is repeated until the available time is totally consumed. At this point one has found the optimal total amount to produce for each product within the planning horizon. Of course the procedure above does not match the actual sequence of production and does not recommend the split of the total amount into several lots. This is done by further steps which are somewhat more technical and not described here. 

Off-line measurements differ significantly from on-line techniques. Offline measurements include safety testing in a laboratory, which has the major advantage of providing available time to redesign the process and/or equipment if a risk is identified. Of course, immediate process response is not possible. 

This leads to deciding on the acceleration levels which are viable. In practice, the acceleration levels are often limited by the available time scales for testing. 

I had a couple of minutes to present my side of the story, but the film seemed to be speeded up a bit, making my voice come out several notes higher than normal. I had the paranoid feeling that the speed-up might be a subtle attempt to make me sound less manly, but perhaps it was just a way to compress available time. 

First detailed studies of the dynamic structure factor of highly entangled polymer melts were reported at the beginning of the 90 s. At that time the attainable Fourier times were limited to about 40 ns. On this time scale, NSE has already played a crucial role in helping to understand the dynamics of polymeric systems [49, 50, 72, 73]. At that time the existence of an entanglement length scale in a linear polymer was been proven [72]. However, with the available time resolution, it was not possible to separate the predictions of the different confinement models addressed above. 

T raining T/F T/F Training was available, timely (initially and in reviews) adequate and verified to be effective to achieve functional and compliance requirements... 

Both quadricyclane and norbornadiene are high-energy isomers of C7H8, and it is interesting to compare their thermal behavior. Figures 4.5 and 4.6 show the pyrolysis breakdown behavior for norbornadiene and quadricyclane, respectively, extracted as described above. As shown, norbornadiene (NBD) is stable on the available time scale for temperatures up to 600 K. (The small apparent decrease in NBD contribution in the 400-600 K range is within the uncertainty of the fitting process — no product species are observed.) Above 600 K decomposition... 

The results for quadricyclane (QC) shown in Fig. 4.6 are qualitatively similar to those for norbornadiene, except that the onset of decomposition for quadricyclane is about 100 K lower. QC is stable on the available time scale at temperatures up to 523 K, above which decomposition sets in rapidly. The QC is completely decomposed within 2 ms (Table 4.1) by about 750 K. As with norbornadiene, the dominant low-temperature decomposition channel is fragmentation to C5H6 + C2H2, while isomerization to more stable isomers (TOL) becomes increasingly important at higher temperatures. There is some evidence for production of norbornadiene in the 700-800 K temperature range, but at higher... 

Thus, as noted in Ref 12a, p 4, the chemical reaction in normal detonation includes a fast first stage and a slow second stage. The low-order detonation is supported by only the first the second is too slow for completion in the available time or is quenched as a result of lateral expansion or other loss mechanism... 

---