Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Component list

I have derived a process for preferentially separating the Safrole out of Sassafras Oil. This process is based on the physical properties of the various components listed above combined with a little chemistry knowledge. The normal means of purifying Sassa-... [Pg.35]

Table 7-3. Intensity Components Listed According to Mode of Excitation... Table 7-3. Intensity Components Listed According to Mode of Excitation...
C05-0145. Find the partial pressures in atmospheres of the eight most abundant atmospheric components listed in Table 5 at 25 °C, 50% relative humidity, and P = 765 torr. [Pg.349]

Consider the first three components listed for the gaseous product. Random statistics favor C as a product despite this, B is the major product. This suggests that equilibrium is achieved via the pathway, A B <= C. This is the expected pathway if isomerization occurs via the 1,3-hydrogen transfer depicted in Eqs. (17)—(19) on this basis, CH2=CH—CD2H, corresponding to B, should be the initial product. The surface product, which had more opportunity for reaction, is, as expected, somewhat closer to the statistical equilibrium. [Pg.40]

The coefficients f, g, and h in Eq. (23) can only depend on the nonvanishing susceptibility components listed in Table 9.2 and are, for a chiral isotropic surface, given by (a more detailed derivation of these expressions can be found elsewhere)21 ... [Pg.534]

The pressure-temperature ratings of components listed in Table IP-8.1 are accepted for pressure design in accordance with Chapter IP-3. [Pg.117]

These components would normally be evaluated in a rodent species (preferably rats) and, in addition, embryo-fetal development would be evaluated in a second species, typically the rabbit. The most probable option in the ICH guideline is the case where three rodent studies would be conducted that separately addressed each of the components listed above. These study designs are described below. The day of insemination or detection of evidence of mating is considered Day 0 of gestation and the day of birth is considered postpartum and postnatal Day 0. Figure 8.1 presents line charts for the ICH Stage-Study Designs. [Pg.259]

J) In the course of a thermometric titration, the thermister attached to the insulated-beaker is connected to one arm of the Wheatstone Bridge as displayed in Figure 11.5. The values of the circuit component listed are for a thermister having an approximate resistance of 2 KI2 and a sensitivity of 0.04 Q/Q/°C in the 25°C temperature range. Hence, an observed change of 1°C = an unbalanced potential of 15.7 mV, and... [Pg.201]

The reaction is set up on ice by adding first the DEPC-treated water to a 1.5 mL microfuge tube and subsequently all other components listed earlier, except the polymerase. [Pg.331]

The components listed in Table 20-1 are typical for PCR. As can be seen, it is a fairly simple reaction to set up. The template and primer concentrations must be determined beforehand the buffer, enzyme, and deoxynucleotide triphosphate (dNTP) mixture are commercially available. [Pg.434]

After adding the first five components listed in Table 20-1, water is added to bring the reaction volume to a total of 50 pi. Ensure that the contents of the tube are mixed by pipetting the contents up and... [Pg.434]

One thing that has been added to the amendment is clear expiry dates for the exemption of about half of those materials and components listed in Annex II. A lot of those expiration DA dates apply to the exempt status for lead compounds in vehicles. [Pg.30]

Figure 5.15 Dimensional compatibility field for stable garnets according to Novak and Gibbs (1971). Points correspond to 12 main components listed in table 5.21. Molar volumes are also indicated. Figure 5.15 Dimensional compatibility field for stable garnets according to Novak and Gibbs (1971). Points correspond to 12 main components listed in table 5.21. Molar volumes are also indicated.
Immiscibility phenomena in silicate melts imply positive deviations from ideality in the mixing process. Ghiorso et al. (1983) developed a mixing model applicable to natural magmas adopting the components listed in table 6.12. Because all components have the same standard state (i.e., pure melt component at the T and P of interest) and the interaction parameters used do not vary with T, we are dealing with a regular mixture of the Zeroth principle (cf sections 2.1 and 3.8.4) ... [Pg.439]

Four 250-ml flasks are filled with the components listed in Table 3.7 as described above under a). [Pg.178]

The first number in brackets, e.g. 16, refers to the number of carbon atoms in the fatty acid and the second number, e.g. 0, refers to the number of double bonds in the fatty acid. The percentage of each component is determined in relation to the sum of the areas of the chromatographic peaks of all the components listed above. [Pg.216]

The material specification of all components listed in Table H.1 shall be clearly stated in the vendor s proposal. Materials shall be identified by reference to applicable International Standards, including the material grade (Tables H.2 and H.3 may be used for guidance). Where International Standard materials are not available, internationally recognised national or other standards may be used. If no such designations are available, the vendor s material specification, giving physical properties, chemical composition and test requirements shall be included in the proposal. [Pg.64]

In 1992, researchers developed an engineering and costing design for a fixed unit that operated at a rate of 2 tons per hour. Costs were estimated to be 149 (Canadian) per metric ton of soil treated. This estimate was based on the following assumptions the unit used medium naphtha as a solvent operations were 24 hours per day, for 260 days per year utilization factor of the facility was 83% capital costs were 2,548 million (Canadian) and capital amortized over 10 years at 10%, two payments per year. The estimate stipulated that the recovered oil was of suitable quality to be sold to offset process costs. It was estimated that the largest component of process costs would be labor ( 56 per ton of waste treated). Other cost components listed were capitalization costs ( 38 per ton), utilities ( 29 per ton), insurance ( 9 per ton), trucking and maintenance (each 5 per ton), equipment rental and site excavation and restoration (each 3 per ton), and waste disposal was estimated to cost 1 per ton (D17896F, p. 8). [Pg.811]

To use the database functions of Orcad Capture you need the five components listed below. Most users will only need to follow step 5, which shows how to install and set up the data base. Make sure that you follow these instructions completely. [Pg.548]

Although other compounds may be found in the gum fraction, the components listed constitute the major portion of the existent gum volume. [Pg.177]

Similarly to LEAP1, the top 20 similar molecules per reaction component list are used, as a default setting, to ensure balanced sampling of reactants for each reaction component and the reasonable performance. This is user adjustable. [Pg.263]

Indirectly heated UHT milk + indicates a component that makes a strong contribution to the flavour. In addition to the components listed, a further 12 unknowns made strong contributions. [Pg.295]

Figure A.5 Components list with methanol concentration at 0.1 g/g water. Figure A.5 Components list with methanol concentration at 0.1 g/g water.
Nutritional Requirements It is important to be able to cultivate bacteria under laboratory conditions to study their characteristics. To be able to do this, one must know what food material and physical conditions are required. Bacterial cells that are actively growing are about 90 percent water. The elemental composition of bacteria is listed in Table 5.2. The nutritional medium to cultivate bacteria should contain those basic components listed. [Pg.95]

A good transdermal process validation will also involve the components listed in Table 1. Transdermal process validation is therefore no different from validation for any other product or process. All of these things must undergo some form of validation to assure that the objective is met—that the end product is manufactured under a stable and consistent process and is therefore fit for... [Pg.287]

The Installation Qualification consists of a description of the lyophilization equipment, a system hardware and component list, the documentation of the installation procedures, and the equipment start-up and operator training. The IQ also includes references to the purchase specifications, engineering review, and SOPs. The objectives are to assure that the equipment design and construction are appropriate for the intended use, it is installed properly, the utilities are suitable and adequate, and that procedures are in place for proper maintenance and operation. [Pg.335]

The composition of the 152 samples in the calibration sample set is shown in the first three columns of Table 11.2 the second and third columns of the table indicate the maximum and minimum concentrations (in volume %) found in the calibration sample set for the components listed in the first column. [Pg.411]

Component lists Flowsheet Globab =l QJ libraries -j Dynamics columns... [Pg.167]

In addition to inulin and the tuber chemical components listed in Table 5.1, notable phytochemicals present in the tubers include gentisic acid (antibacterial and antiviral activity), heliangin (plant... [Pg.56]

Major components listed under a general heading for eucalyptus would be citronellal, cineole, camphene, fenchene, limonene, phellandrene and pinene. The individual species show the different proportions (amounts shown are approximate percentages) ... [Pg.175]

The physical situation is supported by a comparison of computed bandshapes with the measured conventional dimer absorption, the temperature dependence of which is well described. Figure 23 illustrates the situation with three spectra of a 2 M DMEP solution in CCI4 taken at 260 K (a), 298 K (b), and 343 K (c). The measured data points can be fitted well with the already determined spectral components listed in Table 3. Again, the... [Pg.78]

Using any of the above methods, the genealogical aspects of these synthetic approaches become obvious in that these synthetic operations involve/manifest all or a portion of the genealogical components listed below ... [Pg.226]

Hayashi Y, Tsuboi W, Shoji M, Suzuki N (2003a) Application of high pressure induced by water-freezing to the direct catalytic asymmetric three-component List-Barbas-Mannich reaction. J Am Chem Soc 125 11208-11209... [Pg.39]


See other pages where Component list is mentioned: [Pg.945]    [Pg.121]    [Pg.23]    [Pg.86]    [Pg.252]    [Pg.509]    [Pg.73]    [Pg.9]    [Pg.222]    [Pg.258]    [Pg.264]    [Pg.688]    [Pg.27]    [Pg.387]    [Pg.328]    [Pg.94]    [Pg.67]    [Pg.91]   


SEARCH



© 2024 chempedia.info