Addition process

The shaded areas in Fig. 6.24, known as pockets, represent areas of additional process-to-process heat transfer. Remember that the profile of the grand composite curve represents residual heating and cooling demands after recovering heat within the shifted temperature intervals in the problem table algorithm. In these pockets in Fig. 6.24, a local surplus of heat in the process is used at temperature differences in excess of AT ,in to satisfy a local deficit. ... 

Turning now to the cold-end design, Fig. 16.6a shows the pinch design with the streams ticked off. If there are any cold streams below the pinch for which the duties eu e not satisfied by the pinch matches, additional process-to-process heat recovery must be used, since hot utility must not be used. Figure 16.66 shows an additional match to satisfy the residual heating of the cold streams below the pinch. Again, the duty on the unit is maximized. Finally, below the pinch the residual cooling duty on the hot streams must be satisfied. Since there are no cold streams left below the pinch, cold utility must be used (Fig. 16.6c). 

As regards reaetions other than nitration brought about by some of these systems, especially noteworthy are the addition processes undergone by eertain indole derivatives when treated with solutions of nitrie aeid in aeetie aeid. Produets inelude glycols, nitro-alcohols, and nitro-alcohol acetates. Such additions might well be encountered with some polynuclear aromatie eompounds, and with sueh eompounds the possibility of nitration by addition-elimination must always be borne in mind. 

Sample Preparation Most analytical methods can be applied to analytes in a liquid or solution state. For this reason a gross sample of a liquid or solution does not need additional processing to bring it into a more suitable form for analysis. 

Item (2) requires that each event in the addition process be independent of all others. We have consistently assumed this throughout this chapter, beginning with the copolymer composition equation. Until now we have said nothing about testing this assumption. Consideration of copolymer sequence lengths offers this possibility. 

In Figure 8.26 is shown the AXumLum Auger spectrum of sodium in crystalline NaCl. Once again, the formation of the >2 weakly, the core states can be observed. Also shown are peaks resulting from additional processes in which the initial photoelectron with... 

The yield of acrylonitrile based on propylene is generally lower than the yield of acryhc acid based on the dkect oxidation of propylene. Hence, for the large volume manufacture of acrylates, the acrylonitrile route is not attractive since additional processing steps are involved and the ultimate yield of acrylate based on propylene is much lower. Hydrolysis of acrylonitrile can be controUed to provide acrylamide rather than acryhc acid, but acryhc acid is a by-product in such a process (80). 

Two processes may be used in the manufacture of combustible cases the original post-impregnation process and the more recently and more widely employed beater additive process. The processes differ primarily in the point at which the required resin is added to the composition. A schematic of the beater additive process is shown in Figure 11. 

Fig. 11. Flow diagram for the beater additive process. Kraft represents the kraft process wood pulp and NC is nitrocellulose used as starting materials...

The beater additive process starts with a very dilute aqueous slurry of fibrous nitrocellulose, kraft process woodpulp, and a stabilizer such as diphenylamine in a felting tank. A solution of resin such as poly(vinyl acetate) is added to the slurry of these components. The next step, felting, involves use of a fine metal screen in the shape of the inner dimensions of the final molded part. The screen is lowered into the slurry. A vacuum is appHed which causes the fibrous materials to be deposited on the form. The form is pulled out after a required thickness of felt is deposited, and the wet, low density felt removed from the form. The felt is then molded in a matched metal mold by the appHcation of heat and pressure which serves to remove moisture, set the resin, and press the fibers into near final shape (180—182). 

Essentia.1 Oils. Essential oils (qv) are extracted from the flower, leaf, bark, fmit peel, or root of a plant to produce flavors such as mint, lemon, orange, clove, cinnamon, and ginger. These volatile oils are removed from plants either via steam distillation, or using the cold press method, which avoids heat degradation. Additional processing is sometimes employed to remove the unwanted elements from the oils, such as the terpenes in citms oils which are vulnerable to oxidation (49,50). 

In the most common production method, the semibatch process, about 10% of the preemulsified monomer is added to the deionised water in the reactor. A shot of initiator is added to the reactor to create the seed. Some manufacturers use master batches of seed to avoid variation in this step. Having set the number of particles in the pot, the remaining monomer and, in some cases, additional initiator are added over time. Typical feed times ate 1—4 h. Lengthening the feeds tempers heat generation and provides for uniform comonomer sequence distributions (67). Sometimes skewed monomer feeds are used to offset differences in monomer reactivity ratios. In some cases a second monomer charge is made to produce core—shell latices. At the end of the process pH adjustments are often made. The product is then pumped to a prefilter tank, filtered, and pumped to a post-filter tank where additional processing can occur. When the feed rate of monomer during semibatch production is very low, the reactor is said to be monomer starved. Under these... 

Although most lime is sold as quicklime, production of hydrated lime is also substantial. This product is made by the lime manufacturer in the form of a fluffy, dry, white powder, and its use obviates the necessity of slaking. Small lime consumers caimot economically justify the additional processing step that hydration entails. 

Another method of purifying niobium is by distillation of the anhydrous mixed chlorides (29). Niobium and tantalum pentachlorides boil within about 15°C of one another which makes control of the process difficult. Additionally, process materials must withstand the corrosion effects of the chloride. The system must be kept meticulously anhydrous and air-free to avoid plugging resulting from the formation of niobium oxide trichloride, NbOQ. Distillation has been used commercially in the past. 

Papermaking additives can be categorized either as process additives or as functional additives. Process additives are materials that improve the operation of the paper machine, such as retention and drainage aids, biocides, dispersants, and defoamers they are primarily added at the wet end of the paper machine. Functional additives are materials that enhance or alter specific properties of the paper product, such as fillers (qv), sizing agents, dyes, optical brighteners, and wet- and dry-strength additives they may be added internally or to the surface of the sheet. 

The acid process has three advantages over the alkaline process, ie, (/) higher yield of phosphine (60 vs 25%) (2) more pure gas for use in subsequent reactions (95 vs 40%) and (J) by-product phosphoric acid is relatively valuable and can be sold into a number of markets, eg, in the manufacture of fertilizers and flame retardants. There is no ready outlet for the mixture of phosphites produced via the alkaline route and additional processing by oxidative spray drying is needed to produce phosphates for sale (3). 

The processing methods for siHcone mbber are similar to those used in the natural mbber industry (59,369—371). Polymer gum stock and fillers are compounded in a dough or Banbury-type mixer. Catalysts are added and additional compounding is completed on water-cooled roU mills. For small batches, the entire process can be carried out on a two-roU mill. Heat-cured siHcone mbber is commercially available as gum stock, reinforced gum, partially filled gum, uncatalyzed compounds, dispersions, and catalyzed compounds. The latter is ready for use without additional processing. Before being used, sihcone mbber is often freshened, ie, the compound is freshly worked on a mbber mill until it is a smooth continuous sheet. The freshening process eliminates the stmcturing problems associated with polymer—filler interactions. 

In the reaction of ethylene with sulfuric acid, several side reactions can lead to yield losses. These involve oxidation, hydrolysis—dehydration, and polymerization, especially at sulfuric acid concentrations >98 wt % the sulfur thoxide can oxidize by cycHc addition processes (99). 

In-Plant Waste Control. Pollution can be reduced or eliminated by process modification, chemical and raw materials substitution, or recovery of by-products. In addition, process modification generally increases product yield by incorporating control devices. 

Secondary Timber Products. Secondary timber products are products manufactured from primary timber products. Secondary products can be sold directly to the final consumer or can requite additional processing before reaching the final consumer. The wide diversity of products manufactured from primary timber products makes it difficult to precisely define secondary products. Lumber, for example, is clearly a secondary product because it is manufactured from roundwood and typically requites further processing before reaching its final use. Wooden furniture is considered a final product, not a secondary product because it is made from lumber or other secondary timber products. In general, products made from secondary timber products were not included in this analysis. 

Potential consumer benefits from biotechnology (56) are cost and quaUty. The use of biotech means to increase the level of various sulfur-containing amino acids in coffee proteins, and to enhance sucrose and oil levels, could have an impact on the flavor and aroma of the finished ground coffee product. Also, caffeine level modification/elimination through genetic manipulations of the coffee plant could yield low caffeine coffee without additional processing by the manufacturer. 

Concentrates are made in the same manner as dispersions but often with less work placed into the colorant—vehicle system, thus higher yields and rates are obtained and a lower cost product is made. Usually, the concentrate goes through an additional processing step with the resin in which additional energy is provided to the system, thus ensuring more dispersion. 

---