Acetone and oxidation

While keeping the collected deuterioammonia at dry ice-isopropyl alcohol temperature, lithium wire (10 mg) is added, followed by a solution of 3/3-hydroxy-5a-cholest-7-en-6-one (161 50 mg) in anhydrous tetrahydrofuran (4 ml). The reaction mixture is stirred for 20 min, the cooling bath is then removed and the ammonia is allowed to boil under reflux for 40 min. A saturated solution of ammonium chloride in tetrahydrofuran is added dropwise until the deep blue color disappears and then the ammonia is allowed to evaporate. The residue is extracted with ether and the organic layer washed with dilute hydrochloric acid and sodium bicarbonate solution and then with water. Drying and evaporation of the solvent gives a semicrystalline residue which is dissolved in acetone and oxidized with 8 N chromic acid solution. After the usual workup the residue is dissolved in methanol containing sodium hydroxide (0.2 g) and heated under reflux for 1 hr to remove any deuterium introduced at C-5 or C-7. (For workup, see section II-B). 

Oxidation of primary amines with DMD or other oxidants leads to the formation of a complex mixture of nitroso, oximes, and nitro compounds (76). Utilization of DMD in acetone affords dimethyl nitrone (22). This is likely to be a result of the initial oxidation of primary amine (19) to hydroxylamine (20) with the subsequent condensation of acetone and oxidation of imine (21) (Scheme 2.9) (77). 

The product from Step 1 (22.35 mmol) was dissolved in 300 ml acetone and oxidized using a mixture of Cr03 (58.2 mmol) in 15 ml water containing 6 ml 98% H2SO4. After the addition was completed the mixture stirred overnight and was then poured into water. The resulting solid was filtered, washed, and isolated as a white solid in 91% yield, mp = 212 °C (dec.). H- and C-NMR data supplied. 

These media are essentially an extension of dilute solutions whereby the solute now comprises a significant fraction of the total volume. Nevertheless, the principle remains the same, namely to generate the required radicals. For example, one-electron reduction of the fullerene Cg4 has been effected in nitrogen-saturated toluene/2-propanol/acetone (8 1 1) [42]. Here the solvent primary radicals are converted to (CH3)2 C0H by reduction of acetone and oxidation of 2-propanol. 

The catalytic properties of vanadium containing compounds (expanded layered inateriats where unudaie us the interlayer anion) were investigated for photo oxidation of isopropyl alcohol to acetone and oxidation of o-xylenc to o-tolualdehydc [42]. The samples were active when thermally decomposed in between 620-670K. possibly due to better access of vanadium sites in the interlayer. At this temperature, the framework is partially destroyed with the collapse of the layered structure but without any significant reaction between the vanadate and the framework species. 

Figure 4.3 Attempted oxidation of acetone and oxidation of benzaldehyde. As the reaction proceeds, chromium is reduced, forming a grayish green precipitate.

Fit a 750 ml. round-bottomed flask with a fractionating column attached to a condenser set for downward distillation. Place 500 g. of diacetone alcohol (the crude product is quite satisfactory), 01 g. of iodine and a few fragments of porous porcelain in the flask. Distil slowly. with a small free flame (best in an air bath) and collect the following fractions (a) 56-80° (acetone and a little mesityl oxide) (6) 80-126° (two layers, water and mesityl oxide) and (c) 126-131° (mesityl oxide). Whilst fraction (c) is distilling, separate the water from fraction (6), dry with anhydrous potassium carbonate or anhydrous magnesium sulphate, and fractionate from a small flask collect the mesityl oxide at 126-131°. The yield is about 400 g. 

Out first example is 2-hydroxy-2-methyl-3-octanone. 3-Octanone can be purchased, but it would be difficult to differentiate the two activated methylene groups in alkylation and oxidation reactions. Usual syntheses of acyloins are based upon addition of terminal alkynes to ketones (disconnection 1 see p. 52). For syntheses of unsymmetrical 1,2-difunctional compounds it is often advisable to look also for reactive starting materials, which do already contain the right substitution pattern. In the present case it turns out that 3-hydroxy-3-methyl-2-butanone is an inexpensive commercial product. This molecule dictates disconnection 3. Another practical synthesis starts with acetone cyanohydrin and pentylmagnesium bromide (disconnection 2). Many 1,2-difunctional compounds are accessible via oxidation of C—C multiple bonds. In this case the target molecule may be obtained by simple permanganate oxidation of 2-methyl-2-octene, which may be synthesized by Wittig reaction (disconnection 1). 

Various 4-, 5-, or 4,5-disubstituted 2-aryIamino thiazoles (124), R, = QH4R with R = 0-, m-, or p-Me, HO C, Cl, Br, H N, NHAc, NR2, OH, OR, or OjN, were obtained by condensing the corresponding N-arylthiourea with chloroacetone (81, 86, 423), dichloroacetone (510, 618), phenacyichloride or its p-substituted methyl, f-butyl, n-dodecyl or undecyl (653), or 2-chlorocyclohexanone (653) (Method A) or with 2-butanone (423), acetophenone or its p-substituted derivatives (399, 439), ethyl acetate (400), ethyl acetyl propionate (621), a- or 3-unsaturated ketones (691), benzylidene acetone, furfurylidene acetone, and mesityl oxide in the presence of Btj or Ij as condensing agent (Method B) (Table 11-17). 

PROPENE The major use of propene is in the produc tion of polypropylene Two other propene derived organic chemicals acrylonitrile and propylene oxide are also starting materials for polymer synthesis Acrylonitrile is used to make acrylic fibers (see Table 6 5) and propylene oxide is one component in the preparation of polyurethane polymers Cumene itself has no direct uses but rather serves as the starting material in a process that yields two valuable indus trial chemicals acetone and phenol... 

Hydrolysis of cinenn I gives an optically active carboxylic acid (+) chrysanthemic acid Ozonolysis of (+) chrysanthemic acid followed by oxidation gives acetone and an optically active dicarboxyhc acid (—) caronic acid (C7H10O4) What is the struc ture of (—) caronic acid" Are the two carboxyl groups cis or trans to each other What does this information tell you about the structure of (+) chrysanthemic acid" ... 

Propylene requirements for acrylates remain small compared to other chemical uses (polypropylene, acrylonitrile, propylene oxide, 2-propanol, and cumene for acetone and phenol). Hence, cost and availabihty are expected to remain attractive and new acrylate capacity should continue to be propylene-based until after the turn of the century. 

Aldehydes are important products at all pressures, but at low pressures, acids are not. Carbon monoxide is an important low pressure product and declines with increasing pressure as acids increase. This is evidence for competition between reaction sequence 18—20 and reaction 21. Increasing pressure favors retention of the parent carbon skeleton, in concordance with the reversibiUty of reaction 2. Propylene becomes an insignificant product as the pressure is increased and the temperature is lowered. Both acetone and isopropyl alcohol initially increase as pressure is raised, but acetone passes through a maximum. This increase in the alcohoLcarbonyl ratio is similar to the response of the methanoLformaldehyde ratio when pressure is increased in methane oxidation. 

Propane. Propane is difficult to oxidize in LPO because of its volatility and lack of reactivity. It can, however, be oxidized with a suitable solvent and sufficiently high pressures and temperatures (211). The principal products are acetone and isopropyl alcohol. 

Alcohol autoxidation is carried out in the range of 70—160°C and 1000—2000 kPa (10—20 atm). These conditions maintain the product and reactants as Hquids and are near optimum for practical hydrogen peroxide production rates. Several additives including acids, nitriles, stabHizers, and sequestered transition-metal oxides reportedly improve process economics. The product mixture, containing hydrogen peroxide, water, acetone, and residual isopropyl alcohol, is separated in a wiped film evaporator. The organics and water are taken overhead and further refined to recover by-product acetone and the... 

Isoprene [78-79-5] (2-methyl-1,3-butadiene) is a colorless, volatile Hquid that is soluble in most hydrocarbons but is practically insoluble in water. Isoprene forms binary azeotropes with water, methanol, methylamine, acetonitrile, methyl formate, bromoethane, ethyl alcohol, methyl sulfide, acetone, propylene oxide, ethyl formate, isopropyl nitrate, methyla1 (dimethoxymethane), ethyl ether, and / -pentane. Ternary azeotropes form with water—acetone, water—acetonitrile, and methyl formate—ethyl bromide (8). Typical properties of isoprene are Hsted in Table 1. 

Some unsaturated ketones derived from acetone can undergo base- or acid-catalyzed exothermic thermal decomposition at temperatures under 200°C. Experiments conducted under adiabatic conditions (2) indicate that mesityl oxide decomposes at 96°C in the presence of 5 wt % of aqueous sodium hydroxide (20%), and that phorone undergoes decomposition at 180°C in the presence of 1000 ppm iron. The decomposition products from these reactions are endothermic hydrolysis and cleavage back to acetone, and exothermic aldol reactions to heavy residues. 

Figure 2 illustrates the three-step MIBK process employed by Hibernia Scholven (83). This process is designed to permit the intermediate recovery of refined diacetone alcohol and mesityl oxide. In the first step acetone and dilute sodium hydroxide are fed continuously to a reactor at low temperature and with a reactor residence time of approximately one hour. The product is then stabilized with phosphoric acid and stripped of unreacted acetone to yield a cmde diacetone alcohol stream. More phosphoric acid is then added, and the diacetone alcohol dehydrated to mesityl oxide in a distillation column. Mesityl oxide is recovered overhead in this column and fed to a further distillation column where residual acetone is removed and recycled to yield a tails stream containing 98—99% mesityl oxide. The mesityl oxide is then hydrogenated to MIBK in a reactive distillation conducted at atmospheric pressure and 110°C. Simultaneous hydrogenation and rectification are achieved in a column fitted with a palladium catalyst bed, and yields of mesityl oxide to MIBK exceeding 96% are obtained. 

Methyl vinyl ketone can be produced by the reactions of acetone and formaldehyde to form 4-hydroxy-2-butanone, followed by dehydration to the product (267,268). Methyl vinyl ketone can also be produced by the Mannich reaction of acetone, formaldehyde, and diethylamine (269). Preparation via the oxidation of saturated alcohols or ketones such as 2-butanol and methyl ethyl ketone is also known (270), and older patents report the synthesis of methyl vinyl ketone by the hydration of vinylacetylene (271,272). 

Oxidation. Nitroparaffins are resistant to oxidation. At ordinary temperatures, they are attacked only very slowly by strong oxidi2ing agents such as potassium permanganate, manganese dioxide, or lead peroxide. Nitronate salts, however, are oxidi2ed more easily. The salt of 2-nitropropane is converted to 2,3-dimethyl-2,3-dinitrobutane [3964-18-9], acetone, and nitrite ion by persulfates or electrolytic oxidation. With potassium permanganate, only acetone is recovered. 

Cumene Process. There are several Hcensed processes to produce phenol which are based on cumene (qv) (1,8—11). AH of these processes consist of two fundamental chemical reactions cumene is oxidized with air to form cumene hydroperoxide, and cumene hydroperoxide is cleaved to yield phenol and acetone. In this process, approximately 0.46 kg of acetone and 0.75 kg of phenol are produced per kg of cumene feedstock. 

The estimation of alkoxy groups is not such a simple task. One method (26,68) involves hydrolysis and oxidation of the Hberated alcohol with excess standard potassium dichromate solution. The excess may then be estimated iodometrically. This method is suitable only for methoxides, ethoxides, and isopropoxides quantitative conversion to carbon dioxide, acetic acid, and acetone, respectively, takes place. An alternative method for ethoxides is oxidation followed by distillation, and titration of the Hberated acetic acid. 

In this process, the fine powder of lithium phosphate used as catalyst is dispersed, and propylene oxide is fed at 300°C to the reactor, and the product, ahyl alcohol, together with unreacted propylene oxide is removed by distihation (25). By-products such as acetone and propionaldehyde, which are isomers of propylene oxide, are formed, but the conversion of propylene oxide is 40% and the selectivity to ahyl alcohol reaches more than 90% (25). However, ahyl alcohol obtained by this process contains approximately 0.6% of propanol. Until 1984, ah ahyl alcohol manufacturers were using this process. Since 1985 Showa Denko K.K. has produced ahyl alcohol industriahy by a new process which they developed (6,7). This process, which was developed partiy for the purpose of producing epichlorohydrin via ahyl alcohol as the intermediate, has the potential to be the main process for production of ahyl alcohol. The reaction scheme is as fohows ... 

Aluminum nitrate is available commercially as aluminum nitrate nonahydrate [7784-27-2], A1(N02)3 9H20. It is a white, crystalline material with a melting point of 73.5°C that is soluble in cold water, alcohols, and acetone. Decomposition to nitric acid [7699-37-2], HNO, and basic aluminum nitrates [13473-90-0], A1(0H) (N03) where x + = 3, begins at 130°C, and dissociation to aluminum oxide and oxides of nitrogen occurs above 500°C. 

Oxidation. Isopropyl alcohol can be catalyticaHy oxidized using air or oxygen at high temperatures to give acetone and water. 

Other potential synthetic methods include fermentation (qv) of certain carbohydrates (qv), oxidation of propane, hydrogenation of acetone, and hydrolysis of isopropyl acetate. The hydrogenation of by-product acetone is the only method practiced commercially. 

Other by-products include acetone, carbonaceous material, and polymers of propylene. Minor contaminants arise from impurities in the feed. Ethylene and butylenes can form traces of ethyl alcohol and 2-butanol. Small amounts of / -propyl alcohol carried through into the refined isopropyl alcohol can originate from cyclopropane [75-19-4] in the propylene feed. Acetone, an oxidation product, also forms from thermal decomposition of the intermediate sulfate esters, eg. 

Other Processes. Isopropyl alcohol can be prepared by the Hquid-phase oxidation of propane (118). It is produced iacidentaHy by the reductive condensation of acetone, and is pardy recovered from fermentation (119). Large-scale commercial biological production of isopropyl alcohol from carbohydrate raw materials has also been studied (120—123). 

---