Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Tris electrode

Also, try Electrode Dynamics, by A. C. Fisher, Oxford University Press, Oxford, 1996, which is another title in the Oxford primer series. Its early chapters discuss the transport of analyte through solution and the various rates inherent in a dynamic electrochemistry measurement. It is a readily affordable and readable introduction and highly recommended. [Pg.551]

Cyclic voltammetry (CV), rotating disk electrode (RDE), and rotating ring-disk electrode (RRDE) in a traditional tri-electrode cell are often employed in the study of the ORR kinetics and mechanisms on various catalysts in liquid electrolytes [27, 28]. As shown in Fig. 15.2, a tri-electrode cell contains a working electrode (WE), a reference electrode (RE), and a counter electrode (CE). The CE has much... [Pg.439]

Finding the End Point Potcntiomctrically Another method for locating the end point of a precipitation titration is to monitor the change in concentration for the analyte or titrant using an ion-selective electrode. The end point can then be found from a visual inspection of the titration curve. A further discussion of potentiome-try is found in Chapter 11. [Pg.354]

Controllcd-Currcnt Coulomctry The use of a mediator makes controlled-current coulometry a more versatile analytical method than controlled-potential coulome-try. For example, the direct oxidation or reduction of a protein at the working electrode in controlled-potential coulometry is difficult if the protein s active redox site lies deep within its structure. The controlled-current coulometric analysis of the protein is made possible, however, by coupling its oxidation or reduction to a mediator that is reduced or oxidized at the working electrode. Controlled-current coulometric methods have been developed for many of the same analytes that may be determined by conventional redox titrimetry. These methods, several of which are summarized in Table 11.9, also are called coulometric redox titrations. [Pg.503]

Ampcromctry The final voltammetric technique to be considered is amperome-try, in which a constant potential is applied to the working electrode, and current is measured as a function of time. Since the potential is not scanned, amperometry does not lead to a voltammogram. [Pg.519]

The most significant commercial product is barium titanate, BaTiO, used to produce the ceramic capacitors found in almost all electronic products. As electronic circuitry has been rniniaturized, demand has increased for capacitors that can store a high amount of charge in a relatively small volume. This demand led to the development of highly efficient multilayer ceramic capacitors. In these devices, several layers of ceramic, from 25—50 ]lni in thickness, are separated by even thinner layers of electrode metal. Each layer must be dense, free of pin-holes and flaws, and ideally consist of several uniform grains of fired ceramic. Manufacturers are trying to reduce the layer thickness to 10—12 ]lni. Conventionally prepared ceramic powders cannot meet the rigorous demands of these appHcations, therefore an emphasis has been placed on production of advanced powders by hydrothermal synthesis and other methods. [Pg.500]

There have been a number of cell designs tested for this reaction. Undivided cells using sodium bromide electrolyte have been tried (see, for example. Ref. 29). These have had electrode shapes for in-ceU propylene absorption into the electrolyte. The chief advantages of the electrochemical route to propylene oxide are elimination of the need for chlorine and lime, as well as avoidance of calcium chloride disposal (see Calcium compounds, calcium CHLORIDE Lime and limestone). An indirect electrochemical approach meeting these same objectives employs the chlorine produced at the anode of a membrane cell for preparing the propylene chlorohydrin external to the electrolysis system. The caustic made at the cathode is used to convert the chlorohydrin to propylene oxide, reforming a NaCl solution which is recycled. Attractive economics are claimed for this combined chlor-alkali electrolysis and propylene oxide manufacture (135). [Pg.103]

If these two electrodes are connected by an electronic conductor, the electron flow starts from the negative electrode (with higher electron density) to the positive electrode. The electrode A/electrolyte system tries to keep the electron density constant. As a consequence additional metal A dissolves at the negative electrode, forming A+ in solution and electrons e, which are located on the surface of metal A ... [Pg.4]

It was found that chlorides, chlorates, and nitrates interfere by forming in sol ppts (Ref 6). Later it was found that w sol perchlorates could be analyzed gravimetrically by pptn of the perchlorate ion as tetraphenylarsonium perchlorate (Ksp at 20° = 2.60 0.14 x 10"9). The ppt can be (Tried at 105° and weighed directly (Ref 16). Still more recently a specific perchlorate ion electrode has been developed (Ref 17) which can be used for the potentiometric titration of the perchlorate ion using a soln of tetraphenylarsonium chloride as the titrant (Ref 15). Tetra-phenylphosphonium chloride has been similarly used, but the corresponding Sb compd is too insol in w for practical use (Ref 8), For routine assay of perchlorates for use by the armed forces, a Na carbonate fusion procedure is described in Mil Specs MlL-A-23946 (19 Aug 1964) MIL-A-23948 (19 Aug 1964) (see also under Ammonium Perchlorate). The tetraphenylarsonium chloride procedure has also been proposed for use in Mil Specs (Ref 11)... [Pg.617]

FIGURE 5-14 Structures of some chemical species useful for designing anion-selective electrodes (a) Mn(III) porphyrin (b) vitamin Bi2 derivative (c) tri-n-octyltin chloride (d) lipophilic polyamine macrocyclic compound. [Pg.158]

It thus appears safer, rather than trying to introduce such an ambiguous and sometimes impossible definition of an electrode , simply to replace the or in other circumstances in the above expression of the 1st law of Faraday by provided no catalytic reaction is taking place on the electrode or electrolyte surface . This is not necessary for processes with positive AG. [Pg.536]

Electrochemical promotion, or non-Faradaic Electrochemical Modification of Catalytic Activity (NEMCA) came as a rather unexpected discovery in 1980 when with my student Mike Stoukides at MIT we were trying to influence in situ the rate and selectivity of ethylene epoxidation by fixing the oxygen activity on a Ag catalyst film deposited on a ceramic O2 conductor via electrical potential application between the catalyst and a counter electrode. [Pg.584]

In a crystal-pulling procedure using a tri-arc furnace (Fig. 2), a resistor box, a d.c. power supply (300 A, 80/40 V) and a set of water-cooled power cables are used to bring power and water to the electrodes. The upper part of the furnace is equipped with three equally spaced copper cathodes, to which are fixed W-Rh electrodes. The upper part (cathode) is separated from the lower part (anode) by a transparent quartz glass tube. In the bottom of the furnace there is a tapered opening for a water-cooled copper hearth containing the boride melt. All parts of the furnace are also water... [Pg.286]

This presentation reports some studies on the materials and catalysis for solid oxide fuel cell (SOFC) in the author s laboratory and tries to offer some thoughts on related problems. The basic materials of SOFC are cathode, electrolyte, and anode materials, which are composed to form the membrane-electrode assembly, which then forms the unit cell for test. The cathode material is most important in the sense that most polarization is within the cathode layer. The electrolyte membrane should be as thin as possible and also posses as high an oxygen-ion conductivity as possible. The anode material should be able to deal with the carbon deposition problem especially when methane is used as the fuel. [Pg.95]

Monofunctional and Polyfunctional Electrodes At monofunctional electrodes, one sole electrode reaction occurs under the conditions specified when current flows. At polyfunctional electrodes, two or more reactions occur simultaneously an example is the zinc electrode in acidic zinc sulfate solution. When the current is cathodic, metallic zinc is deposited at the electrode [reaction (1.21)] and at the same time, hydrogen is evolved [reaction (1.27)]. The relative strengths of the partial currents corresponding to these two reactions depend on the conditions (e.g., the temperature, pH, solution purity). Conditions may change so that a monofunctional electrode becomes polyfunctional, and vice versa. In the case of polyfunctional electrodes secondary (or side) reactions are distinguished from the principal (for the given purpose) reaction (e.g., zinc deposition). In the electrolytic production of substances and in other practical applications, one usually tries to suppress all side reactions so that the principal (desired) reaction will occur with the highest possible efficiency. [Pg.17]

We might try to measure the temperature coefficient of the Galvani potential for an individual electrode under nonisothermal conditions then only the temperature of the test electrode would be varied, while the reference electrode remains at a constant temperature and retains a constant value of Galvani potential (Fig. 3.2). [Pg.51]

Cyclic voltammetry is perhaps the most important and widely used technique within the field of analytical electrochemistry. With a theoretical standard hydrogen electrode at hand, one of the first interesting and challenging applications may be to try to use it to make theoretical cyclic voltammograms (CVs). In following, we set out to do this by attempting to calculate the CV for hydrogen adsorption on two different facets of platinum the (111) and the (100) facets. [Pg.60]

Principles and Characteristics Combustion analysis is used primarily to determine C, H, N, O, S, P, and halogens in a variety of organic and inorganic materials (gas, liquid or solid) at trace to per cent level, e.g. for the determination of organic-bound halogens in epoxy moulding resins, halogenated hydrocarbons, brominated resins, phosphorous in flame-retardant materials, etc. Sample quantities are dependent upon the concentration level of the analyte. A precise assay can usually be obtained with a few mg of material. Combustions are performed under controlled conditions, usually in the presence of catalysts. Oxidative combustions are most common. The element of interest is converted into a reaction product, which is then determined by techniques such as GC, IC, ion-selective electrode, titrime-try, or colorimetric measurement. Various combustion techniques are commonly used. [Pg.595]

The reductive coupling of allyl halides to 1,5-hexadiene at glassy C electrodes was catalyzed by tris(2, 2,-bipyridyl)cobalt(II) and tris(4,4 -dimethyl-2, 2/-bipyridyl)cobalt(II) in aqueous solutions of 0.1 M sodium dodecylsulfate (SDS) or 0.1 M cetyltrimethylammonium bromide (CTAB).48 An organocobalt(I) intermediate was observed by its separate voltammetric reduction peak in each system studied. This intermediate undergoes an internal redox reaction to form 1,5-hexadiene... [Pg.181]


See other pages where Tris electrode is mentioned: [Pg.204]    [Pg.440]    [Pg.204]    [Pg.440]    [Pg.558]    [Pg.173]    [Pg.49]    [Pg.2148]    [Pg.88]    [Pg.89]    [Pg.803]    [Pg.562]    [Pg.67]    [Pg.440]    [Pg.117]    [Pg.494]    [Pg.652]    [Pg.132]    [Pg.232]    [Pg.181]    [Pg.78]    [Pg.638]    [Pg.239]    [Pg.244]    [Pg.319]    [Pg.592]    [Pg.102]    [Pg.38]    [Pg.261]    [Pg.137]    [Pg.353]    [Pg.138]   
See also in sourсe #XX -- [ Pg.231 ]




SEARCH



Tri-enzyme electrode

© 2024 chempedia.info