Quartz transparency

BeO mixed with half its weight of sugar carbon and a little oil and heated in an electric furnace for 8-10 minutes with 950 amperes at 40 volts. Obtained carbide whi< h he calls Be Cs (which was undoubtedly BejC) in crystals, harder than quartz, transparent. Specific gravity 1.9 at 15°. Attacked at red heat by Cl, Br, HF, and HCl with liberation of carbon and formation of halide. Slowly decomposed water, liberating CH. Quickly decomposed by caustic alkalies. No other carbide seems to exist. 

Monolayers can be transferred onto many different substrates. Most LB depositions have been perfonned onto hydrophilic substrates, where monolayers are transferred when pulling tire substrate out from tire subphase. Transparent hydrophilic substrates such as glass [18,19] or quartz [20] allow spectra to be recorded in transmission mode. Examples of otlier hydrophilic substrates are aluminium [21, 22, 23 and 24], cliromium [9, 25] or tin [26], all in their oxidized state. The substrate most often used today is silicon wafer. Gold does not establish an oxide layer and is tlierefore used chiefly for reflection studies. Also used are silver [27], gallium arsenide [27, 28] or cadmium telluride wafer [28] following special treatment. 

Cera.micA.bla.tors, Several types of subliming or melting ceramic ablators have been used or considered for use in dielectric appHcations particularly with quartz or boron nitride [10043-11 -5] fiber reinforcements to form a nonconductive char. Fused siHca is available in both nonporous (optically transparent) and porous (sHp cast) forms. Ford Aerospace manufactures a 3D siHca-fiber-reinforced composite densified with coUoidal siHca (37). The material, designated AS-3DX, demonstrates improved mechanical toughness compared to monolithic ceramics. Other dielectric ceramic composites have been used with performance improvements over monolithic ceramics (see COMPOSITE MATERIALS, CERAMIC MATRIX). 

Shock Luminescence. Some transparent materials give off copious amounts of light when shocked to a high pressure, and thus they can serve as shock arrival-time indicators. A technique used by McQueen and Fritz (1982) to measure arrival times of release waves is based on the reduction of shock-induced luminescence as the shock pressure is relieved. Bromoform, fused quartz, and a high-density glass have been used for their shock luminescence properties. 

An additional advantage to neutron reflectivity is that high-vacuum conditions are not required. Thus, while studies on solid films can easily be pursued by several techniques, studies involving solvents or other volatile fluids are amenable only to reflectivity techniques. Neutrons penetrate deeply into a medium without substantial losses due to absorption. For example, a hydrocarbon film with a density of Ig cm havii a thickness of 2 mm attenuates the neutron beam by only 50%. Consequently, films several pm in thickness can be studied by neutron reflecdvity. Thus, one has the ability to probe concentration gradients at interfaces that are buried deep within a specimen while maintaining the high spatial resolution. Materials like quartz, sapphire, or aluminum are transparent to neutrons. Thus, concentration profiles at solid interfaces can be studied with neutrons, which simply is not possible with other techniques. 

Berg-kalk, m. rock time (Geol.) mountain limestone. -kiesel, m. rock flint, chert felsite. -kohle,/. (mineral) coal, -kork, m. mountain cork (a light form of asbestos), -kreide, /. rock lime, -kristall, -krystall, m. rock crystal (transparent quartz), -kupfer, n. native copper, -lasur, /. azurite. -leder, n. mountain leather (a form of asbestos), -maun, m miner. 

Due to the above requirements, typical optically-transparent materials, such as oxides (glass, quartz, alumina, zirconium oxide etc.) and halides (sodium chloride, lithium fluoride, calcium fluoride, potassium bromide, cesium bromide etc.) are usually unsuitable for use with fluoride melts. Therefore, no standard procedure exists at present for the spectral investigation of fluoride melts, and an original apparatus must be created especially for each particular case. 

Serizawa et al. (2002) studied experimentally, through visualization, the two-phase flow patterns in air-water two-phase flows in round tubes. The test section for air-water experiments consisted of a transparent silica or quartz capillary tube with circular cross-section positioned horizontally. The two-phase flow was realized through a mixer with different designs, as shown in Figs. 5.4 and 5.5. The air was injected into the mixer co-axially while water was introduced peripherally. 

In a crystal-pulling procedure using a tri-arc furnace (Fig. 2), a resistor box, a d.c. power supply (300 A, 80/40 V) and a set of water-cooled power cables are used to bring power and water to the electrodes. The upper part of the furnace is equipped with three equally spaced copper cathodes, to which are fixed W-Rh electrodes. The upper part (cathode) is separated from the lower part (anode) by a transparent quartz glass tube. In the bottom of the furnace there is a tapered opening for a water-cooled copper hearth containing the boride melt. All parts of the furnace are also water... 

Similar reflection plates are used for recording ultraviolet-visible and Raman spectra of matrix isolated molecules, although the traditional beam path passing through transparent quartz windows is more frequently used in UV spectrometers. Sapphire rods, which are placed in the spectrometer cavity, are applied as targets in matrix esr studies. 

The experimental procedure employed a capillary viscometer made of quartz as shown in Fig. 26. A solid sample was put in the filtration chamber and the top of the chamber was sealed under a vacuum. Then the sample was heated to melting and filtered into the viscometer and the connecting tube sealed at the middle. The viscometer was settled inside a transparent electric furnace and after the temperature of the melt was stabilized, the furnace containing the viscometer was turned upside down, which transferred the melt into the funnel. Then the tube was turned... 

P 12] A falling film micro reactor was applied for generating thin liquid films [6]. A reaction plate with 32 micro channels of channel width, depth and length of 600 pm, 300 pm and 66 mm, respectively, was used. Reaction plates made of pure nickel and iron were employed. The micro device was equipped with a quartz window transparent for the wavelength desired. A 1000 W xenon lamp was located in front of the window. The spectrum provided ranges from 190 to 2500 nm the maximum intensity of the lamp is given at about 800 nm. 

Flint is a hard and easily split variety of the mineral quartz (composed of silicon dioxide), which occurs not only as flint but also in a wide range of other varieties. Some of these exhibit different colors and colored patterns and have characteristic crystalline structures, while others are amorphous (see Textbox 21). In all its varieties, nevertheless, the hardness of quartz is very high, being graded as 7 on the Mohs scale (see Textbox 23). Almost all varieties are either transparent or translucent and display a distinctive luster. These properties made quartz an attractive material for making ornamental... 

Ferruginous quartz Vitreous Transparent or translucent Red/yellow-brown Inclusions of iron and asbestos... 

Rose quartz Vitreous Transparent or translucent Pink/red-rose Usually cracked... 

Smoky quartz Vitreous Transparent or translucent Pale/black Often banded... 

---