To deliver

The jet pump relies on the same hydraulic power being delivered sub-surface as to the hydraulic reciprocating pump, but there the similarity ends. The high-pressure power fluid is accelerated through a nozzle, after whioh it is mixed with the well stream. The velocity of the well stream is thereby increased and this acquired kinetic energy is converted to pressure in an expander. The pressure is then sufficient to deliver the fluids to surface. The jet pump has no moving parts and can be made very compact. 

The end product specification of a process may be defined by a customer (e.g. gas quality), by transport requirements (e.g. pipeline corrosion protection), or by storage considerations (e.g. pour point). Product specifications normally do not change, and one may be expected to deliver within narrow tolerances, though specification can be subject to negotiation with the customer, for example In gas contracts. 

One of the primary objectives of production operations is to deliver product at the required rate and quality. Therefore the product quality specification and any agreed contract terms will drive the activities of the production operations department, and will be a starting point for determining the preferred mode of operation. The specifications, such as delivery of stabilised crude with a BS W of less than 0.5%, and a salinity of 70 g/m, ... 

The purpose of the surface facilities is to deliver saleable hydrocarbons from the wellhead to the customer, on time, to specification, in a safe and environmentally acceptable manner. The main functions of the surface facilities are... 

Flowever, in order to deliver on its promise and maximize its impact on the broader field of chemistry, the methodology of reaction dynamics must be extended toward more complex reactions involving polyatomic molecules and radicals for which even the primary products may not be known. There certainly have been examples of this notably the crossed molecular beams work by Lee [59] on the reactions of O atoms with a series of hydrocarbons. In such cases the spectroscopy of the products is often too complicated to investigate using laser-based techniques, but the recent marriage of intense syncluotron radiation light sources with state-of-the-art scattering instruments holds considerable promise for the elucidation of the bimolecular and photodissociation dynamics of these more complex species. 

Amount of material required. It is convenient to employ an arbitrary ratio of 0 10 g. of solid or 0 20 ml. of liquid for 3 0 ml. of solvent. Weigh out 0 10 g. of the finely-powdered solid to the nearest 0 01 g. after some experience, subsequent tests with the same compound may be estimated by eye. Measure out 0-20 ml. of the liquid either with a calibrated dropper (Fig. 11,27, 1) or a small graduated pipette. Use either a calibrated dropper or a graduated pipette to deliver 3 0 ml. of solvent. Rinse the delivery pipette with alcohol, followed by ether each time that it is used. 

Glassware designed to deliver a specific volume of solution when filled to its calibration mark. 

So what is the total uncertainty when using this pipet to deliver two successive volumes of solution from the previous discussion we know that the total uncertainty is greater than 0.000 mL and less than 0.012 mL. To estimate the cumulative effect of multiple uncertainties, we use a mathematical technique known as the propagation of uncertainty. Our treatment of the propagation of uncertainty is based on a few simple rules that we will not derive. A more thorough treatment can be found elsewhere. ... 

The class A 10-mL pipet characterized in Table 4.8 is used to deliver two successive volumes. Calculate the absolute and relative uncertainties for the total delivered volume. 

Volumetric glassware used to deliver variable, but known volumes of solution. 

Titrations may be automated using a pump to deliver the titrant at a constant flow rate, and a solenoid valve to control the flow (Figure 9.5). The volume of titrant delivered is determined by multiplying the flow rate by the elapsed time. Automated titrations offer the additional advantage of using a microcomputer for data storage and analysis. 

Lasers are used to deliver a focused, high density of monochromatic radiation to a sample target, which is vaporized and ionized. The ions are detected in the usual way by any suitable mass spectrometer to produce a mass spectrum. The yield of ions is often increased by using a secondary ion source or a matrix. 

The key functions of dentifrices, to remove dental stains and to freshen the oral cavity, are accomplished by abrasive cleaning and the masking or elimination of unpleasant oral odors. Materials designed to deliver antitartar, antiplaque, or anticaries benefits must be compatible with the ability of the dentifrice to tiilfill those two functions. 

Design of explosion suppression systems is clearly complex, since the effectiveness of an explosion suppression system is dependent on a large number of parameters. One Hypothesis of suppression system design identifies a limiting combustion wave adiabatic flame temperature, below which combustion reactions are not sustained. Suppression is thus attained, provided that sufficient thermal quenching results in depression of the combustion wave temperature below this critical value. This hypothesis identifies the need to deliver greater than a critical mass of suppressant into the enveloping fireball to effect suppression (see Fig. 26-43). 

Tetracycline antibiotics have found wide application in animal industries for treatment, preventive maintenance and stimulation of growth of large horned livestock owing to what their residue amounts can be present at milk and meat of animals. Residue amounts of antibiotics are not toxic, however, capable to cause allergic reactions and to promote development of tolerance of the some people pathogenic bacterias. According with the legislative requirements of a number of the European countries it is forbidden to deliver to the population production polluted residual contents of tetracyclines. 

For the customer to ascertain the capability of a producer to deliver goods or services to the required standards it is essential for the producer to have all documents that establish his or her competence to deliver the goods or services, according to the prescribed Quality Standards. These documents may cover... 

The expander shall be guaranteed to deliver the shaft horsepower at the normal operating eonditions (pressures, temperatures, flowrate, speed, and gas analysis) with a toleranee of -0 and -1-4%. 

The press had been designed with a capacity to deliver 280 kN press force and to work at a production rate of 40 lids per minute. Calculations to determine the distribution of forming loads required indicated that the press capacity was adequate to form the family of steel lids to be produced on the machine. One of the major areas of interest in the design was the con-rod and pin (see Figure 4.66). The first option considered was based on a previous design where the con-rod was manufactured from cast iron with phosphor bronze bearings at the big and small ends. However, weaknesses in this approach necessitated the consideration of other options. The case study presents the analysis of the pin and con-rod using simple probabilistic techniques in an attempt to provide in-service reliable press operation. The way a weak link was introduced to ensure ease of maintenance and repair in the event... 

Main fuel injector. This unit is designed to deliver a fuel-air mixture to the catalyst that is uniform in composition, temperature, and velocity. A multi-venturi tube (MVT) fuel injection system was developed by GE specifically for this purpose. It consists of 93 individual venturi tubes arrayed across the flow path, with four fuel injection orifices at the throat of each venturi. 

The overall plant needs the following parameters to be computed. The most important two parameters from an economic point of view are the computation of the power delivered and the fuel consumed to deliver... 

There is also another limitation of controllers that is often overlooked. A controller must be given only its one Job to do, not several. For example, a level controller might be designed to deliver feed to a process having a varying demand. A boiler level controller is such an example. This controller can be designed... 

The linear program can be designed to deliver a wealth of base case information, such as ... 

---