Teflon®

FEP plastics Copolymers of tetrafluoro-ethene and hexafluoropropene. Inert and corrosion resistant as Teflon but can be processed by melt techniques. 

Kel-F Trade name for a polymeric chlorotri-fluoroethene, often copolymerized. May be a liquid or solid. Inert to chemical attack and a thermoplastic (Teflon cannot be moulded). 

A zero or near-zero contact angle is necessary otherwise results will be low. This was found to be the case with surfactant solutions where adsorption on the ring changed its wetting characteristics, and where liquid-liquid interfacial tensions were measured. In such cases a Teflon or polyethylene ring may be used [47]. When used to study monolayers, it may be necessary to know the increase in area at detachment, and some calculations of this are available [48]. Finally, an alternative method obtains y from the slope of the plot of W versus z, the elevation of the ring above the liquid surface [49]. 

Fig. X-9. Zisman plots of the contact angles of various homologous series on Teflon O, RX , alkylbenzenes (f), n-alkanes , dialkyl ethers , siloxanes A, miscellaneous polar liquids. (Data from Ref. 78.)...

Figure X-9 shows plots of cos 6 versus 7l for various series of liquids on Teflon (polytetrafluoroethylene) [78]. Each line extrapolates to zero at a certain 7l value, which Zisman has called the critical surface tension 7 since various series extrapolated to about the same value, he proposed that 7 was a quantity characteristic of a given solid. For Teflon, the representative 7 was taken to be about 18 and was regarded as characteristic of a surface consisting of —CF2 — groups.

Contact angle will vary with liquid composition, often in a regular way as illustrated in Fig. X-13 (see also Ref. 136). Li, Ng, and Neumann have studied the contact angles of binary liquid mixtures on teflon and found that the equation of state that describes... 

Calculate from the data available in the text the value of imm for Teflon in benzene at around 20°C. 

A number of friction studies have been carried out on organic polymers in recent years. Coefficients of friction are for the most part in the normal range, with values about as expected from Eq. XII-5. The detailed results show some serious complications, however. First, n is very dependent on load, as illustrated in Fig. XlI-5, for a copolymer of hexafluoroethylene and hexafluoropropylene [31], and evidently the area of contact is determined more by elastic than by plastic deformation. The difference between static and kinetic coefficients of friction was attributed to transfer of an oriented film of polymer to the steel rider during sliding and to low adhesion between this film and the polymer surface. Tetrafluoroethylene (Telfon) has a low coefficient of friction, around 0.1, and in a detailed study, this lower coefficient and other differences were attributed to the rather smooth molecular profile of the Teflon molecule [32]. 

Microwaves from the waveguide are coupled into the resonator by means of a small coupling hole in the cavity wall, called the iris. An adjustable dielectric screw (usually machined from Teflon) with a metal tip adjacent to the iris pennits optimal impedance matching of the cavity to the waveguide for a variety of samples with different dielectric properties. With an appropriate iris setting the energy transmission into the cavity is a maximum and simultaneously reflections are minimized. The optimal adjustment of the iris screw depends on the nature of the sample and is found empirically. 

On a laboratory scale, hydrotliennal syntliesis is usually carried out in Teflon-coated, stainless-steel autoclaves under autogenous pressure. A typical syntliesis mixture consists of up to four major constituents, a T-atoni source (silicon and aluminium, otlier elements may also be incoriiorated as indicated above), a solvent (almost exclusively... 

Stirrers are usually made of glass, but those of monel metal, stainless steel or Teflon (a polyfluoroethylene) also find application in the labora tory. An important advantage of a stirrer with a Teflon blade is that it is... 

All of the pieces pictured here are not going to fit perfectiy into each other and that s going to cause all sorts of leaks. The answer is teflon tape. Strike loves teflon tape This inexpensive product is found in the plumbing department of any hardware store and is the duct tape of the next century. Teflon tape is chemically and thermally indestructible. This stuff is wrapped around any piece of pipe or joint, said part then jammed into its appropriate receptacle and the tape will mold to form a perfect fit. Hell, it can mummify a whoie joint compiex to make it absolutely impregnable. 

Teflon stir bar 1 heavy duty balloon 1 roll of electrical tape Magnetic stirrer Support stand and clamps Ohaus triple beam scale 1 plastic funnel... 

Tetrafluoroethene F2C = CF2 (-CF2-CF2-) (Teflon) Nonstick coating for cooking utensils bearings gaskets and fittings... 

Teflon IS made in a similar way by free radical polymerization of tetrafluoroethene... 

Carbon-fluorine bonds are quite strong (slightly stronger than C—H bonds) and like polyethylene Teflon is a very stable inert material We are all familiar with the most characteristic property of Teflon its nonstick surface This can be understood by com paring Teflon and polyethylene The high electronegativity of fluorine makes C—P bonds less polarizable than C—H bonds causing the dispersion forces m Teflon to be less than those m polyethylene Thus the surface of Teflon is even less sticky than the already slick surface of polyethylene... 

Class A conforms to specifications in ASTM E694 for standard taper stopcocks and to ASTM E287 for Teflon or poly-tetrafluoroethylene stopcock plugs. The 10-mL size meets the requirements for ASTM D664. ... 

Fig. 2.15 Isosteric heat of adsorption of nitrogen on molecular (low-evergy) solids and on carbons (high-energy solids), plotted as a function of i/n . (A) Diamond (B) gruphitized carbon black. P.33 (D) Benzene (E) Teflon. The curve for amorphous carbon was very close to Curve (A). (Redrawn from a Figure of Adamson . )...

---