Teflon-type solids

Among solids, teflon exhibits the largest hydrophobicity (9 = 108°). Solids of teflon type, with their high contact angles, are called naturally hydrophobic and float without the assistance of chemical reagents. Artificial hydrophobicity to which the collector contributes is really not required to float solids or minerals characterized by natural hydrophobicity. 

In the most suitable test configuration for foods, the sample initially completely fills the gap between two coaxial horizontal discs, one attached to the base and the other to the crosshead, of a UTM-type solids rheometer. Lubrication between the sample and disc surfaces is achieved by Teflon coating the surfaces and/or deliberately lubricating the surfaces with a suitable liquid of very low viscosity. 

Indicate, if known, preferred bag material that will withstand environment, e.g., fibers of glass, polyester, Teflon , Nomex , polypropylene, polyethylene, cotton, wool, nylon, Orion , Dacron , and Dynel . The type of weave of fiber should be recommended by the manufacturer. The fabrics may be felted or woven [47,48] in weaves of plain, satin, or twill, and should be resistant to any corrosive material in the solid particles or the gas stream. 

The liquid stationary phase in a GLC packed column is adsorbed on the surface of a solid substrate (also called the support). This material must be inert and finely divided (powdered). The typical diameter of a substrate particle is 125 to 250 ft, creating a 60- to 100-mesh material. These particles are of two general types diatomaceous earth and Teflon . Diatomaceous earth, the decayed silica skeletons of algae, is most commonly referred to by the manufacturer s (Johns Manville s) trade name, Chromosorb . Various types of Chromosorb, which have had different pretreatment procedures applied, are available, such as Chromosorb P, Chromosorb W, and Chromosorb 101-104. The nature of the stationary phase as well as the nature of the substrate material are both usually specified in a chromatography literature procedure, and columns are tagged to indicate each of these as well. 

Some potential limitations associated with this protocol merit note. For example, with sequence A in Fig. 1, insoluble by-products will interfere with catalyst recovery. With sequence B, interference will depend upon the type of support. For instance, the Teflon tape in Fig. 8 should be easily separable from another solid material, as would a mesh or reactor liner. Also, since heating is required to achieve homogeneity, the method is best suited for reactions conducted at elevated temperatures. However, there are many reactions which proceed rapidly under fluorous/organic liquid/liquid biphase conditions (i.e., before the miscibility temperature is reached) [55-57,70]. Therefore, it is not unreasonable to expect that sohd fluorous catalysts with little or no solubility can also efficiently promote certain reactions, as represented by sequence A-1 in Fig. 1 [29]. 

Macroelectrodes with solid membranes contain homogeneous [142] or heterogeneous [25] membranes. The construction of an ISE of this type with an internal reference electrode is shown in fig. 4.1. For good functioning of an ISE it is necessary that the membrane be completely sealed in the electrode body, with no cracks leading to short-circuiting between the external and internal solutions. Cements based on Teflon, PVC or epoxy resin are used (170). 

Filters collect liquid and solid particles by mechanisms including diffusion, impaction, interception, electrostatic attraction, and sedimentation onto the filter while allowing the gas to pass through. The types commonly used in atmospheric particulate collection are membranes, fibrous mats, or porous sheets. Different filter materials are used depending on the particular type of measurement being carried out, including Teflon, quartz fiber, nylon, silver, cellulose filters, glass fibers, and polycarbonate. The characteristics of each are summarized by Chow (1995). 

Two types of columns are used. A packed column is one filled with inert, solid particles coated with a liquid stationary phase. Standard tubing is about 0.5 cm in diameter, with lengths ranging from 1 m to 20 m however, columns for large-scale preparative work may be up to 5 cm in diameter and several meters long. Commonly used solid supports are diatomaceous earth, Teflon powder, and glass beads. The stationary liquid must be chosen on the basis of the compounds to be analyzed. A more recently developed and more widely used type of column is the open-tubular or capillary column. This is prepared by coating the inner wall of the column with the stationary liquid phase. The inside diameter of a typical capillary tube is 0.25 mm, and... 

The PEFC was first developed for the Gemini space vehicle by General Electric, USA. In this fuel cell type, the electrolyte is an ion-exchange membrane, specifically, a fluorinated sulfonic acid polymer or other similar solid polymer. In general, the polymer consists of a polytetrafluoroethylene (Teflon) backbone with a perfluorinated side chain that is terminated with a sulfonic acid group, which is an outstanding proton conductor. Hydration of the membrane yields dissociation and solvation of the proton of the acid group, since the solvated protons are mobile within the polymer. Subsequently, the only liquid necessary for the operation of this fuel cell type is water [7,8],... 

Most on-line procedures involving microwaves that are conducted with a view to coupling a microwave treatment (usually digestion) with a detector (usually of the atomic type) for the determination of analytes use either a domestic oven [37-40] or a commercial focused system [41-43] plus appropriate connections. Usually, the coupling is done by inserting a Teflon coil in the oven in order to circulate the suspended solid sample to be subjected to the microwaves [44]. Some systems use domestic or commercial focused systems where the solid sample is directly placed in the sample vessel [45] and an aspiration system is used after the microwave treatment to transfer the extract to the determinative instrument used [37,46] or to an apparatus employed in some other step of the analytical process [40,43]. 

---