Susceptibility pitting

A variety of sealants have been explored or developed (168), with many people having one or more applications of a sealant. Sealants are vital for promotion of adhesion, which significantly reduces caries formation (169-177). Pit and fissure sealants are covered under the American Dental Association (ADA) Acceptance Program. These materials are used to seal high caries-susceptible pits and fissures of the deciduous and permanent molars, and also to seal microspaces between the tooth and restorative materials, enabling these materials to adhere firmly both to prepared cavity walls and to other restoratives. They provide dental pulp protection and protection from secondary caries formation. 

Titanium is susceptible to pitting and crevice corrosion in aqueous chloride environments. The area of susceptibiUty for several alloys is shown in Figure 7 as a function of temperature and pH. The susceptibiUty depends on pH. The susceptibiUty temperature increases paraboHcaHy from 65°C as pH is increased from 2ero. After the incorporation of noble-metal additions such as in ASTM Grades 7 or 12, crevice corrosion attack is not observed above pH 2 until ca 270°C. Noble alloying elements shift the equiUbrium potential into the passive region where a protective film is formed and maintained. 

Crevice Corrosion. Crevice corrosion is intense locali2ed corrosion that occurs within a crevice or any area that is shielded from the bulk environment. Solutions within a crevice are similar to solutions within a pit in that they are highly concentrated and acidic. Because the mechanisms of corrosion in the two processes are virtually identical, conditions that promote pitting also promote crevice corrosion. Alloys that depend on oxide films for protection (eg, stainless steel and aluminum) are highly susceptible to crevice attack because the films are destroyed by high chloride ion concentrations and low pH. This is also tme of protective films induced by anodic inhibitors. 

The stainless steels contain appreciable amounts of Cr, Ni, or both. The straight chrome steels, types 410, 416, and 430, contain about 12, 13, and 16 wt % Cr respectively. The chrome—nickel steels include type 301 (18 wt % Cr and 9 wt % Ni), type 304 (19 wt % Cr and 10 wt % Ni), and type 316 (19 wt % Cr and 12 wt % Ni). Additionally, type 316 contains 2—3 wt % Mo which gready improves resistance to crevice corrosion in seawater as well as general corrosion resistance. AH of the stainless steels offer exceptional improvement in atmospheric conditions. The corrosion resistance results from the formation of a passive film and, for this reason, these materials are susceptible to pitting corrosion and to crevice corrosion. For example, type 304 stainless has very good resistance to moving seawater but does pit in stagnant seawater. 

Area effects in galvanic corrosion are very important. An unfavorable area ratio is a large cathode and a small anode. Corrosion of the anode may be 100 to 1,000 times greater than if the two areas were the same. This is the reason why stainless steels are susceptible to rapid pitting in some environments. Steel rivets in a copper plate will corrode much more severely than a steel plate with copper rivets. 

Evidence of localized corrosion can be obtained from polarization methods such as potentiodynamic polarization, EIS, and electrochemical noise measurements, which are particularly well suited to providing data on localized corrosion. When evidence of localized attack is obtained, the engineer needs to perform a careful analysis of the conditions that may lead to such attack. Correlation with process conditions can provide additional data about the susceptibility of the equipment to locaHzed attack and can potentially help prevent failures due to pitting or crevice corrosion. Since pitting may have a delayed initiation phase, careful consideration of the cause of the localized attack is critical. Laboratory testing and involvement of an... 

Finally, pitting may be viewed as a special form of concentration cell corrosion. Most alloys that are susceptible to crevice corrosion also pit. However, many metals may pit but not show crevice attack. Further, although sharing many common features with concentration cell corrosion, pitting is sufficiently different to warrant a separate categorization. 

Stress-corrosion cracks tend to branch along the metal surfaces. Typically, evidence of corrosion, such as accumulations of corrosion products, is not observed, although stains in the cracked region may be apparent. Stress-corrosion cracks tend to originate at physical discontinuities, such as pits, notches, and corners. Areas that may possess high-residual stresses, such as welds or arc strikes, are also susceptible. 

If the technical regulations are adhered to for constructional steels in neutral waters, there are no conditions for H-induced corrosion. On the other hand, hardened and high-strength materials with hardnesses above HV 350 are very susceptible [60,82,92], since anodic polarization encourages crack formation in saline media and anodic pitting occurs with acid products of hydrolysis [93]. 

Embrittlement embrittlement and for improperly heat treated steel, both of which give intergranular cracks. (Intercrystalline penetration by molten metals is also considered SCC). Other steels in caustic nitrates and some chloride solutions. Brass in aqueous ammonia and sulfur dioxide. physical environments. bases of small corrosion pits, and cracks form with vicious circle of additional corrosion and further crack propagation until failure occurs. Stresses may be dynamic, static, or residual. stress relieve susceptible materials. Consider the new superaustenitic stainless steels. 

Metals which owe their good corrosion resistance to the presence of thin, passive or protective surface films may be susceptible to pitting attack when the surface film breaks down locally and does not reform. Thus stainless steels, mild steels, aluminium alloys, and nickel and copper-base alloys (as well as many other less common alloys) may all be susceptible to pitting attack under certain environmental conditions, and pitting corrosion provides an excellent example of the way in which crystal defects of various kinds can affect the integrity of surface films and hence corrosion behaviour. 

Stainless steels are particularly prone to crevice corrosion, and even the Fe-18Cr-8Ni-3Mo type of austenitic stainless steel, which is highly resistant to pitting when the surface is free from crevices, is susceptible although initiation of attack may take 1-2 years... 

Tomashov, N. D., Chernova, G. P. and Marcova, O. N., Effect of Supplementary Alloying Elements on Pitting Corrosion Susceptibility of 18Cr-14Ni Stainless Steel , Corrosion, 20, 166 (1964)... 

Bianchi, G., Corguetti, A., Mazza, F. and Torchio, S., Electronic Properties of Oxide Films and Pitting Susceptibility of Type 304 Stainless Steel , Corros. Sci., 12, 495 (1972) Szkiarska-Smialowska, Z. and Mankowski, J., Effect of Temperature on the Kinetics of... 

Herbsleb, G. and Schwenk, W., Flow Dependence of the Pitting Corrosion of Cr-Ni Steel in NaCl Solution. 2 Tests with Ultrasonics , Werkst. Korros., 24, 267 (1973) C.A., 79, 56638n El Din Shams, A. M., Bodran, M. M. and Khalil, S. E., Corrosion Behaviour of Manganese-containing Stainless Steel. 3 Their Susceptibility Towards Pitting Corrosion , Werkst. Korros., 24, 290 (1973) C.A., 79, 56642j... 

The literature contains a number of studies on the susceptibility of the cobalt-based alloys to pitting corrosion. In-vitro studies conducted by Mueller and Greener , involving static conditions, revealed no evidence of pitting having occurred. Syrett and Wing ", utilising cyclic polarisation analyses, observed that neither as-cast nor annealed Co-Cr-Mo alloy demonstrated hysteresis loops in their cyclic polarisation curves. They... 

Syrett and Davis conducted in-vivo studies wherein they implanted crevice corrosion specimens of Co-Cr-Mo in dogs and rhesus monkeys for up to two years. Their results indicated the alloy was not susceptible to crevice corrosion. Galante and Rostoker implanted crevice-type specimens of Co-Cr-Mo and Ti-6A1-4V in the back of rabbits for 12 months. Although no evidence of severe corrosion was found in any of the specimens, several of the titanium and cobalt specimens did show signs of single pits in the crevice regions. 

Lucas, L. C., Buchanan, R. A., Lemons, J. E., and Griffin, C. D., Susceptibility of Surgical Cobalt-Base Alloy to Pitting Corrosion , Journal of Biomedical Materials Research, 16, 799-810 (1982)... 

Shot peening is a beneficial surface treatment since it puts the surface into a state of compression and generally obscures the grain structure. Subsequent painting of the peened surface is often useful. If pitting occurs then cracking can be expected in susceptible material when the attack penetrates the depth of the compressed surface layer. 

New alloys with improved corrosion-resistance characteristics are continually being marketed, and are aimed at solving a particular problem, e.g. improved stress-corrosion cracking resistance in the case of stainless steels improved pitting resistance or less susceptibility to welding difficulties. 

Stainless steels Thin-walled stainless steel (Fe-18Cr-8Ni) tubes are now frequently used for domestic installations in place of copper pipe . Care is required, however, in the design of stainless steel equipment for use in waters with a high chloride content, or where the concentration can increase, since pitting attack may occur. It may also be susceptible to failure by stress-corrosion cracking under certain conditions. 

---