Potentiodynamic polarization

Figures 13a-b. Typical potential-current density patterns obtained for copper-2% zinc alloy in protein solutions cathodically polarized potentiodynamically at 2 Hz(broad), 200 kHz(flat) (a)y ana at 200 Hz (b).

The present study of corrosion processes of metallic materials uses variable current technology, namely the electrochemical polarization potentiodynamic and electrochemical impedance spectroscopy (EIS) techniques. The basis of polarization potentiodynamic electrochemical technique is the stimulation of the corrosion system by a potential, whose value varies linearly in time and the recording of the instantaneous value of current flowing in the system The electrochemical impedance spectroscopy consists of a perturbation of the... 

The potentiodynamic polarization electrochemical technique can be used to study and interpret corrosion phenomena. It may also furnish useful information on film breakdown or repair. 

Linear polarization re.slstance probe.s. LPR probes are more recent in origin, and are steadily gaining in use. These probes work on a principle outlined in an ASTM guide on making polarization resistance measurements, providing instantaneous corrosion rate measurements (G59, Standard Practice for Conducting Potentiodynamic Polarization Resistance Measurements ). 

Polarization probe.s. Polarization methods other than LPR are also of use in process control and corrosion analysis, but only a few systems are offered commercially. These systems use such polarization techniques as galvanodynamic or potentiodynamic, potentiostatic or galvanostatic, potentiostaircase or galvanostaircase, or cyclic polarization methods. Some systems involving these techniques are, in fact, used regularly in processing plants. These methods are used in situ or... 

Information on the process reaction conditions may be impoi tant to prolonging the lifetime of process equipment. Techniques such as EIS and potentiodynamic polarization can provide just such information without being tied to a specific corrosion-rate measurement. 

ASTM G59, Standard Prac tice for Conducting Potentiodynamic Polarization Resistance Measurements, provides instructions for the graphical plotting of data (from tests conducted using the above-noted ASTM Standard G103) as the hnear potential versus current density, from which the polarization resistance can be found. 

Evidence of localized corrosion can be obtained from polarization methods such as potentiodynamic polarization, EIS, and electrochemical noise measurements, which are particularly well suited to providing data on localized corrosion. When evidence of localized attack is obtained, the engineer needs to perform a careful analysis of the conditions that may lead to such attack. Correlation with process conditions can provide additional data about the susceptibility of the equipment to locaHzed attack and can potentially help prevent failures due to pitting or crevice corrosion. Since pitting may have a delayed initiation phase, careful consideration of the cause of the localized attack is critical. Laboratory testing and involvement of an... 

Bessing, C., Bergman, M. and Thoren, A. Potentiodynamic Polarization Analysis of Low-gold and Silver-Palladium Alloys in Three Different media. Dental Materials, 3, 153-159 (1987)... 

Ringas and Robinson performed electrochemical tests on stainless steels and mild steels in three cultures of SRB. In all cases pitting resistance was lower in cultures of SRB. Potentiodynamic polarization... 

Scan Rates Sweeping a range of potentials in the anodic (more electropositive) direction of a potentiodynamic polarization curve at a high scan rate of about 60 V/h (high from the perspective of the corrosion engineer, slow from the perspective of a physical chemist) is to indicate regions where intense anodic activity is likely. Second, for otherwise identical conditions, sweeping at a relatively slow rate of... 

Environmental tests have been combined with conventional electrochemical measurements by Smallen et al. [131] and by Novotny and Staud [132], The first electrochemical tests on CoCr thin-film alloys were published by Wang et al. [133]. Kobayashi et al. [134] reported electrochemical data coupled with surface analysis of anodically oxidized amorphous CoX alloys, with X = Ta, Nb, Ti or Zr. Brusic et al. [125] presented potentiodynamic polarization curves obtained on electroless CoP and sputtered Co, CoNi, CoTi, and CoCr in distilled water. The results indicate that the thin-film alloys behave similarly to the bulk materials [133], The protective film is less than 5 nm thick [127] and rich in a passivating metal oxide, such as chromium oxide [133, 134], Such an oxide forms preferentially if the Cr content in the alloy is, depending on the author, above 10% [130], 14% [131], 16% [127], or 17% [133], It is thought to stabilize the non-passivating cobalt oxides [123], Once covered by stable oxide, the alloy surface shows much higher corrosion potential and lower corrosion rate than Co, i.e. it shows more noble behavior [125]. 

Fig. 14. Potentiodynamic polarization curves obtained on FeTb and FeTb/Si02 samples in pH 3.1 CF-containing solution [159], (Reprinted by permission of The IEEE).

Corrosion inhibition of mild steel in acid solutions by 2-aryl-5-oxadiazolinethiones (2-hydroxyphenyl, 2-phenyl, and 2-cinnamyl) has been observed <2002MCH425>. The potentiodynamic polarization data have shown that compounds studied predominantly behave as cathodic inhibitors in acid solutions. 

The potential-independent CPT determined by the potentiodynamic method is defined as the lowest temperature at which pitting initiation occurs during a dynamic anodic polarization scan. ... 

For perovskite electrodes, the earliest kinetic study of hysteretic effects appears to come from Ham-mouche and co-workers, who showed that the i—rj characteristics of porous LSM/YSZ in air at 960 °C exhibit a potentiodynamic hysteresis when scanned slowly (1 mV/s) between 0 and —1200 mV cathodic polarization. " A clearer demonstration of this effect, more recently provided by Jiang and co-workers, is shown in Figure 41.232,233 Hammouche and co-workers attributed this hysteresis to the formation of oxygen vacancies in LSM at high overpotential, which (as discussed in sections 5.2 and 5.3) appears to open a parallel bulk-transport-mediated reaction pathway. However, if this was the only explanation. 

Standard Reference Method for Making Potentiostatic and Potentiodynamic Anodic Polarization Measurements", ASTM G5-72. "Evaluating Degree of Rusting on Painted Steel Surfaces", ASTM D610-68. 

---