Sulfonated PTFE

Sulfonated PTFE, Nation membrane, of equivalent weight (EW) of 1100 ... 

Electrolyte KOH sulfonated PTFE phosphoric acid U/Na carbonate Y-ZrOj... 

Illustrative performance properties for a "general purpose polycarbonate," and for the same resin modified with the additive formulations "700" (without PTFE) and "800" (with PTFE) are summarized in Table IV (adapted from reference 32). It is clear that the objective of minimal effect on performance properties has been attained for this system. It is evident that flame retardant effectiveness attained with minimal levels of additive can provide optimum solutions to the problem of decreasing flammability without sacrifice in performance properties. Work documented to date suggests that in depth studies of thermal degradation such as reported for aromatic sulfonates in polycarbonates (28) would be rewarding for other systems. 

Since PTFE was first synthesized more than 50 years ago, fluoropolymers have been produced by radical polymerization and copolymerizaton processes, but without any functional groups, for several reasons. First, the synthesis of functional vinyl compounds suitable for radical polymerization is much more complicated and expensive in comparison with common fluoroolefins. In radical polymerization of one of the simplest possible candidates—perfluorovinyl sulfonic acid (or sulfonyl fluoride—there was not enough reactivity to provide high-molecular-weight polymers or even perfluorinated copolymers with considerable functional comonomer content. Several methods for the synthesis of the other simplest monomer—trifluoroacrylic acid or its esters—were reported,1 but convenient improved synthesis of these compounds as well as radical copolymerization with TFE induced by y-irradiation were not described until 1980.2... 

Grafting of functional monomers onto fluoropolymers produced a wide variety of permselective membranes. Grafting of styrene (with the following sulfonation), (meth)acrylic acids, 4-vinylpyridine, A-vinylpyrrolidone onto PTFE films gave membranes for reverse omosis,32-34 ion-exchange membrane,35-39 membranes for separating water from organic solvents by pervaporation,49-42 as well as other kinds of valuable membranes. 

Mg(II) forms a complex with 8-hydroxyquinoline-5-sulfonic acid (37) at pH 9.0 with Tris-HCl buffer, which can be determined by ELD (X x = 388 nm, ka = 495 nm) with micellar enhancement by cetyltrimethylammonium chloride (38). Masking of Ca(II) is achieved by EGTA (19). The method was applied in a SIA system for analysis of natural waters . After elution of the Mg(II) ions adsorbed on an alkali-activated PTFE tube with 0.1 M HCl and addition of A,A -bis(salicylidene)-2,3-diaminobenzofuran (39), the end analysis was by fluorometric determination of the Mg(II) complex (kex =475 nm, kfl = 545 nm). Possible interference of Ca(II) is masked on addition of the chelating agent... 

All work has been accomplished using perfluorosulfonate ion exchange membranes manufactured by E.l. duPont and sold under the trade name Nafion. Nafion is a copolymer of polytetrafluoroethy-lene (PTFE) and polysulfonylfluoride vinyl ether containing pendent sulfonic acid groups. The sulfonic acid groups are chemically bound to the perfluorocarbon backbone. 

PC PE PES PET PF PFA PI PMMA PP PPO PS PSO PTFE PTMT PU PVA PVAC PVC PVDC PVDF PVF TFE SAN SI TP TPX UF UHMWPE UPVC Polycarbonate Polyethylene Polyether sulfone Polyethylene terephthalate Phenol-formaldehyde Polyfluoro alkoxy Polyimide Polymethyl methacrylate Polypropylene Polyphenylene oxide Polystyrene Polysulfone Polytetrafluoroethylene Polytetramethylene terephthalate (thermoplastic polyester) Polyurethane Polyvinyl alcohol Polyvinyl acetate Polyvinyl chloride Polyvinyl idene chloride Polyvinylidene fluoride Polyvinyl fluoride Polytelrafluoroethylene Styrene-acrylonitrile Silicone Thermoplastic Elastomers Polymethylpentene Urea formaldehyde Ultrahigh-molecular-weight polyethylene Unplasticized polyvinyl chloride... 

FIG. 31 Lap shear strength at break between two identical (a) styrene sulfonic acid and (b) DMAA graft-polymerized PTFE films as a function of adhesion (drying) time and plasma pretreatment time. (From Ref. 93.)... 

PB PBI PBMA PBO PBT(H) PBTP PC PCHMA PCTFE PDAP PDMS PE PEHD PELD PEMD PEC PEEK PEG PEI PEK PEN PEO PES PET PF PI PIB PMA PMMA PMI PMP POB POM PP PPE PPP PPPE PPQ PPS PPSU PS PSU PTFE PTMT PU PUR Poly(n.butylene) Poly(benzimidazole) Poly(n.butyl methacrylate) Poly(benzoxazole) Poly(benzthiazole) Poly(butylene glycol terephthalate) Polycarbonate Poly(cyclohexyl methacrylate) Poly(chloro-trifluoro ethylene) Poly(diallyl phthalate) Poly(dimethyl siloxane) Polyethylene High density polyethylene Low density polyethylene Medium density polyethylene Chlorinated polyethylene Poly-ether-ether ketone poly(ethylene glycol) Poly-ether-imide Poly-ether ketone Poly(ethylene-2,6-naphthalene dicarboxylate) Poly(ethylene oxide) Poly-ether sulfone Poly(ethylene terephthalate) Phenol formaldehyde resin Polyimide Polyisobutylene Poly(methyl acrylate) Poly(methyl methacrylate) Poly(methacryl imide) Poly(methylpentene) Poly(hydroxy-benzoate) Polyoxymethylene = polyacetal = polyformaldehyde Polypropylene Poly (2,6-dimethyl-l,4-phenylene ether) = Poly(phenylene oxide) Polyp araphenylene Poly(2,6-diphenyl-l,4-phenylene ether) Poly(phenyl quinoxaline) Polyphenylene sulfide, polysulfide Polyphenylene sulfone Polystyrene Polysulfone Poly(tetrafluoroethylene) Poly(tetramethylene terephthalate) Polyurethane Polyurethane rubber... 

---