Solvent propertie

The powerful solvent properties of dimethylsulfoxide (DMSO), for example, are used to dissolve selectively the polynuclear aromatics found in oils and paraffins. The procedure is shown in Figure 2.5. 

Dearomatized or not, lamp oils correspond to petroleum cuts between Cio and C14. Their distillation curves (less than 90% at 210°C, 65% or more at 250°C, 80% or more at 285°C) give them relatively heavy solvent properties. They are used particularly for lighting or for emergency signal lamps. These materials are similar to kerosene solvents , whose distillation curves are between 160 and 300°C and which include solvents for printing inks. 

F. M. Fowkes, in Solvent Properties of Surfactant Solutions, K. Shinoda, ed., Marcel Dekker, New York, 1967. 

Homologous mono-alkyl ethers of ethylene glycol, such as monoethyl glycol (or 2-ethoxyethanol), HOC2H4OC2H5, form excellent solvents as they combine to a large extent the solvent properties of alcohols and ethers. The monoethyl and the monomethyl members have the technical names of ethyl cellosolve and methyl cellosolve respectively. Dioxan... 

HC0N(CH3)2, also possess exceptional solvent properties. The alkyl-glycols, dioxan and dimethyl-formamide should be used with caution, however, as their hot vapours are poisonous. 

The most widely used cleansing agent is the chromic acid cleaning mixture. It is essentially a mixture of chromic acid (CrOj) and concentrated sulphuric acid, and possesses powerful oxidising and solvent properties. Two methods of preparation are available —... 

Solvents exert their influence on organic reactions through a complicated mixture of all possible types of noncovalent interactions. Chemists have tried to unravel this entanglement and, ideally, want to assess the relative importance of all interactions separately. In a typical approach, a property of a reaction (e.g. its rate or selectivity) is measured in a laige number of different solvents. All these solvents have unique characteristics, quantified by their physical properties (i.e. refractive index, dielectric constant) or empirical parameters (e.g. ET(30)-value, AN). Linear correlations between a reaction property and one or more of these solvent properties (Linear Free Energy Relationships - LFER) reveal which noncovalent interactions are of major importance. The major drawback of this approach lies in the fact that the solvent parameters are often not independent. Alternatively, theoretical models and computer simulations can provide valuable information. Both methods have been applied successfully in studies of the solvent effects on Diels-Alder reactions. 

The solvents listed in Table 2.1 were chosen to cover a broad range in solvent properties. In fact hexane was initially also among them, but unfortunately the rate of the reaction in this solvent is extremely low. It turned out that in this solvent spontaneous decomposition of 2.4a competes with the Diels-Alder reaction. 

At one time benzene was widely used as a solvent This use virtually disappeared when statistical studies revealed an increased incidence of leukemia among workers exposed to atmospheric levels of benzene as low as 1 ppm Toluene has replaced benzene as an inexpensive organic solvent because it has similar solvent properties but has not been determined to be carcinogenic m the cell systems and at the dose levels that benzene is... 

Solvent molecules Solvent Orange 60 Solvent Orange 63 Solvent preparation Solvent process Solvent properties... 

The extremely nonpolar character of PFCs and very low forces of attraction between PFC molecules account for their special properties. Perfluorocarbons bod only slightly higher than noble gases of similar molecular weight, and their solvent properties are much more like those of argon and krypton than hydrocarbons (2). The physical properties of some PFCs are Hsted in Table 1. 

The combined pharmaceutical appHcations account for an estimated 25% of DMF consumption. In the pharmaceutical industry, DMF is used in many processes as a reaction and crystallizing solvent because of its remarkable solvent properties. For example, hydrocortisone acetate [50-03-3] dihydrostreptomycin sulfate [5490-27-7] and amphotericin A [1405-32-9] are pharmaceutical products whose crystallization is faciHtated by the use of DMF. Itis also a good solvent for the fungicide griseofulvin/72%(97-< 7 and is used in its production. 

ROOC—COOH, are not. The dialkyl esters are characterized by good solvent properties and serve as starting materials in the synthesis of many organic compounds, such as pharmaceuticals, agrochemicals, and fine chemicals (qv). Among the diesters, dimethyl, diethyl, and di- -butyl oxalates are industrially important. Their physical properties are given in Table 7. 

Solvent. The solvent properties of water and steam are a consequence of the dielectric constant. At 25°C, the dielectric constant of water is 78.4, which enables ready dissolution of salts. As the temperature increases, the dielectric constant decreases. At the critical point, the dielectric constant is only 2, which is similar to the dielectric constants of many organic compounds at 25°C. The solubiUty of many salts declines at high temperatures. As a consequence, steam is a poor solvent for salts. However, at the critical point and above, water is a good solvent for organic molecules. 

Sulfolane was first described ia the chemical Hterature ia 1916. It has been noted for its exceptional chemical and thermal stabiUty and unusual solvent properties. The search for a commercial process to produce sulfolane began about 1940. Market development quantities became available ia 1959. Siace then, both the use of and the appHcations for sulfolane have iacreased dramatically. 

Reactions. Supercritical fluids are attractive as media for chemical reactions. Solvent properties such as solvent strength, viscosity, diffusivity, and dielectric constant may be adjusted over the continuum of gas-like to Hquid-like densities by varying pressure and temperature. Subsequently, these changes can be used to affect reaction conditions. A review encompassing the majority of studies and apphcations of reactions in supercritical fluids is available (96). 

Distillation By-Products. Of the CTO distiHation by-products, ie, pitch, heads, and DistiHed TaH Oil (DTO), only the last, a unique mixture of rosin and fatty acids, has significant commercial value. Pitch and heads are used as fuel the former has a fuel value of 41,800 kj/kg. TaH oil heads have outstanding solvent properties, but also have a bad odor, which is hard to remove. They contain a relatively high fraction of palmitic acid which can be recovered by crystallization. 

Salts and Derivatives. Generally the vitamers are high melting crystalline soHds that are very soluble in water and insoluble in most other solvents. Properties of the common forms are Hsted in Table 1. The only commercially important form of vitamin B is pytidoxine hydrochloride (7). This odorless crystalline soHd is composed of colorless platelets melting at 204—206°C (with decomposition). In bulk, it appears white and has a density of - 0.4 kg/L. It is very soluble in water (ca 0.22 kg/L at 20°C), soluble in propylene glycol, slightly soluble in acetone and alcohol (ca 0.014 kg/L), and insoluble in most lipophilic solvents. A 10% water solution shows a pH of 3.2. Both the hydrochloride and corresponding free base sublime without decomposition (16). 

The NF and reagent grades are employed in the pharmaceutical industry which makes use of benzyl alcohol s local anesthetic, antiseptic, and solvent properties (17—20). It also finds use in cough symps and drops ophthalmic solutions bum, dental (21), and insect repeUant solutions and ointments and dermatological aerosol sprays. It is used in nail lacquers and as a color developer in hair dyes by the cosmetics industry (22), and in acne treatment preparations (23). 

Tetrachloroethylene [127-18-4] perchloroethylene, CCl2=CCl2, is commonly referred to as "perc" and sold under a variety of trade names. It is the most stable of the chloriaated ethylenes and ethanes, having no flash poiat and requiring only minor amounts of stabilizers. These two properties combiaed with its excellent solvent properties account for its dominant use ia the dry-cleaning iadustry as well as its appHcation ia metal cleaning and vapor degreasiag. 

Chlorotoluene [106-43-4] (l-chloto-4-methylbenzene, PCT) and y -chlorotoluene [108-41-8] (l-chloto-3-methylbenzene, MCT) ate mobile, colorless Hquids with solvent properties similar to those of the ortho isomer. 

K. Shiaoda, ed.. Solvent Properties of Suf actant Solutions, Suf actant Science Series, Vol. 2, Marcel Dekker, Inc., New York, 1967. 

In addition to its ability to make the separation feasible or easier, the ideal solvent is inexpensive, readily available, nontoxic, noncorrosive, thermally stable, and nonreactive with and easily separated from the other components in the mixture. In reaUty some compromise in solvent properties is almost always required. 

---