RELEVANT DATA

The intend in this section is to provide that reader some experimental data available in the literature. In practice, cathode materials and reference (RE) electrodes used in anodic protection are given in Tables 9.1 and 9.2, respectively. 

Silver-Silver Chloride Sulfuric Acid, Kraft Digester Liquid 

Stainless Steel Liquid Fertilizers (Nitrate Solutions) 

Nickel-Plate Steel Chemical Nickel Plating Solutions 

Anodic protection AP) is a potential-control electrochemical technique suitable for preventing corrosion of a metal in aggressive environments, such as sulfuric add (H2SO4). In this technique, the metal to be protected must exhibit passivity at relatively low current density so that the passive current density (ip) is at least one order of magnitude lower than the carosion current density (icorr)-care must be exerdse in selecting a material that shows a wide enough passive potential range. Thus, the protective potential is Epa Ex Ep. 

---

In this discussion, entropy factors have been ignored and in certain cases where the difference between lattice energy and hydration energy is small it is the entropy changes which determine whether a substance will or will not dissolve. Each case must be considered individually and the relevant data obtained (see Chapter 3), when irregular behaviour will often be found to have a logical explanation. 

Comparison of the relevant data shows that an adjacent oxygen (Table 5) and especially a sulfur atom (Table 6) induce lower field shifts than either type of nitrogen atom. 

Is there a system m place that insures that for each order all relevant data (i.e., product name, volume, product information, time, place, documentation etc.) IS collected prior to execution ... 

Works in diserete time - only snap-shots of the system output through the A/D eonverter are available. Henee, to ensure that all relevant data is available, the frequeney of sampling is very important. 

All chemical operations produce waste either as solid wastes (including pastes, sludge and drummed liquids), liquid effluents, or gaseous emissions (including gases, particulate solids, mists and fogs). Relevant data are summarized in Chapters 16 and 17. 

NB Other relevant data taken into consideration in making the overall evaluation) Eormaldehyde [50-00-0] (Vol. 62 1995)... 

J, Not classifiable Not enough scientifically relevant data available for classification... 

The highly resolved velocity profile can be mapped in the vicinity of solid boundaries such as the walls of a room and in the entire enclosure, providing relevant data for CFD boundary conditions. These data form a basis for verification of CFD results and for improvement of CFD codes. 

Establish a means of collecting relevant data and transmitting it to personnel for analysis... 

For many of the efficiency measures, the relevant data is collected during audits or by analysis of records. It is likely that your company has an internal reporting cycle with which you should coordinate your meas-... 

Report cost Varies with consulting time required to provide relevant data. 

Note SAIC has selected some data from resources 8.1 through 8.15 to construct its proprietary data files for use in performing PRAs. Relevant data from these files was used to construct the CCPS Generic Failure Rate Data Base. Accordingly, all usable data points contained in the resources used by SAIC may not be in the Data Tables in this book. 

It is important, especially when consistency has not been designed or built into the maintenance reporting system, to review the data reported to minimize misinterpretation. Clearly defined equipment boundaries for plant hardware are essential for the generation of relevant data. For example, one classification method may define pumps as only the mechanical portions of the pump, whereas another may include the driver (e.g., the motor) and associated controls. Interviews with operating and maintenance personnel as well as review of the maintenance procedures and documents can provide insight into the... 

The cost of protection of steelwork in a mild industrial atmosphere has been compared for a number of protection schemes" and the relevant data are shown in Table 9.2. The difference in aggregate costs illustrates the importance of considering protection on a whole life rather than on an initial cost basis particularly when maintenance involves a labour intensive operation such as painting. 

The bottle should be clean and dry a little of the stock solution is introduced, the bottle well rinsed with this solution, drained, the remainder of the solution poured in, and the bottle immediately stoppered. If the bottle is not dry, but has recently been thoroughly rinsed with distilled water, it may be rinsed successively with three small portions of the solution and drained well after each rinsing this procedure is, however, less satisfactory than that employing a clean and dry vessel. Immediately after the solution has been transferred to the stock bottle, it should be labelled with (1) the name of the solution (2) its concentration (3) the data of preparation and (4) the initials of the person who prepared the solution, together with any other relevant data. Unless the bottle is completely filled, internal evaporation and condensation will cause drops of water to form on the upper part of the inside of the vessel. For this reason, the bottle must be thoroughly shaken before removing the stopper. 

We think, therefore, that the conformation, chain and segment mobilities in the attached macromolecules can play a significant role in the shielding behavior of the polymeric stationary phase as well as in the processes of its formation of complexes with solutes. Obviously, the chromatographic studies relevant to composite supports suffer from a lack of information on the structure of the attached polymer. Nevertheless, we will attempt to point out some relevant data from independent studies on polymer adsorption and/or graft polymerization. 

Stress-strain curves at the conditions of product application. If applicable, this would usually indicate the toughness of material by sizing up the area under the curve (Chapter 2). It would also show the proportional limit, yield point, corresponding elongations, and other relevant data. 

Hanstein and Traylor544 used a 4.3 M solution of trifluoroacetic acid in chloroform to measure the rates of deuteration of (PhCH2)2Hg at 35 °C, for which kx = 2,100 x 10"7. Comparison with other deuteration rates (which, however, were neither quoted nor referred to) was said to give a (CH2HgCH2Ph) = — 1.14 and the ortho para ratio was 0.84. For the compound PhCH2B(OH)j, the rate of deuteration by 3 M tartaric acid at 100 °C was found to be 5 x 10 7 (ortho para ratio = 1.1) and from this a value of ff4 (CH2B(OH)J) of —1.11 was claimed, but without the relevant data used to obtain these c+ values cautious use of them seems appropriate. 

Recalculation by the present author from the relevant data yields 0.756. 

All these developments need precise values of the electrochemical systems. Springer Verlag and the editor are very grateful to the author R. Holze who collects and presents all relevant data together with a precise description of the phenomenons in this volume. The data are divided in five ehapters ... 

The present volume presents the results of an attempt to collect all relevant data as complete as possible. In a few cases original sources were not accessible despite considerable efforts. To provide a critical review and a complete reevaluation of the reported data is not the purpose of this collection. Consequently all data are reported, only conversion into standard units and with respect to standard references were made when necessary and reasonable, obvious printing errors were corrected. 

The product selectivity arises from the reaction of this intermediate with the various nucleophiles present in the reaction medium. Therefore, the structure of this intermediate and its close environment (counter-ion, solvent molecules, etc.) determines the product selectivity. It is important to note that the relevant data concern the intermediate as it is formed during the reaction and not prepared under extreme conditions where it is stable, such as those used to obtain the nmr spectra of these ions, for example (ref. 5). Since the life-time of this ionic species in the reaction medium is very short, in the 10 9 - 10-10 s range (ref. 6), there is no way to observe it directly. Consequently, the available data, useful for understanding... 

Human perception is. .. inferred from fragmentary and often hardly relevant data signalled by the eyes, so requiring inferences from knowledge of the world to make sense of the sensory signal. 

Storage is one of the biggest challenges of biodata. If you wish to keep all raw data, ensure that your infrastructure and support and grow in pace with the raw data. If you only want to keep the relevant data, ensure your that business rules are able to filter the raw data properly—that is, do not lose anything vital. Banks spend far greater proportions of their profits on servers... 

Optimal decisions depend, in part, on fully exploiting relevant data and knowledge. This ranges from physiological and pharmacological knowledge... 

---