Reference electrode diffusion

In soil suspensions at low salt concentrations, extraneous (junction) potentials can affect pH readings (Appendix 10,1). The most plausible explanation for junction potentials is that K ions in the KC1 bridge of the reference electrode diffuse more rapidly, and Cl ions less rapidly, when negatively charged soil particles are near the bridge. One answer is to place the reference electrode in the clear supernatant solution and the glass electrode in the settled clay suspension (where H+ is concentrated) to obtain valid soil pH measurements. Junction potentials are essentially eliminated at salt concentrations greater than 0.01 M. 

Cells need not necessarily contain a reference electrode to obtain meaningfiil results as an example, if the two electrodes in figure A2.4.12 are made from the same metal, M, but these are now in contact with two solutions of the same metal ions, M but with differing ionic activities, which are separated from each other by a glass frit that pennits contact, but impedes diffusion, then the EMF of such a cell, temied a concentration cell, is given by... 

Reference electrodes are used in the measurement of potential [see the explanation to Eq. (2-1)]. A reference electrode is usually a metal/metal ion electrode. The electrolyte surrounding it is in electrolytically conducting contact via a diaphragm with the medium in which the object to be measured is situated. In most cases concentrated or saturated salt solutions are present in reference electrodes so that ions diffuse through the diaphragm into the medium. As a consequence, a diffusion potential arises at the diaphragm that is not taken into account in Eq. (2-1) and represents an error in the potential measurement. It is important that diffusion potentials be as small as possible or the same in the comparison of potential values. Table 3-1 provides information on reference electrodes. 

Greater deviations which are occasionally observed between two reference electrodes in a medium are mostly due to stray electric fields or colloid chemical dielectric polarization effects of solid constituents of the medium (e.g., sand [3]) (see Section 3.3.1). Major changes in composition (e.g., in soils) do not lead to noticeable differences of diffusion potentials with reference electrodes in concentrated salt solutions. On the other hand, with simple metal electrodes which are sometimes used as probes for potential controlled rectifiers, certain changes are to be expected through the medium. In these cases the concern is not with reference electrodes, in principle, but metals that have a rest potential which is as constant as possible in the medium concerned. This is usually more constant the more active the metal is, which is the case, for example, for zinc but not stainless steel. 

In addition, the temperature dependence of the diffusion potentials and the temperature dependence of the reference electrode potential itself must be considered. Also, the temperature dependence of the solubility of metal salts is important in Eq. (2-29). For these reasons reference electrodes with constant salt concentration are sometimes preferred to those with saturated solutions. For practical reasons, reference electrodes are often situated outside the system under investigation at room temperature and connected with the medium via a salt bridge in which pressure and temperature differences can be neglected. This is the case for all data on potentials given in this handbook unless otherwise stated. 

Here Ee is the standard potential of the reaction against the reference electrode used to measure the potential of the dropping electrode, and the potential E refers to the average value during the life of a mercury drop. Before the commencement of the polarographic wave only a small residual current flows, and the concentration of any electro-active substance must be the same at the electrode interface as in the bulk of the solution. As soon as the decomposition potential is exceeded, some of the reducible substance (oxidant) at the interface is reduced, and must be replenished from the body of the solution by means of diffusion. The reduction product (reductant) does not accumulate at the interface, but diffuses away from it into the solution or into the electrode material. If the applied potential is increased to a value at which all the oxidant reaching the interface is reduced, only the newly formed reductant will be present the current then flowing will be the diffusion current. The current / at any point... 

Figure 4a. Electrochemical cells for microwave conductivity measurements. Cell above microwave conduit (1) electrochemical cell (plastic tube, placed on working electrode material), (2) counter-electrode, (3) reference electrode, (4) electrolyte, (5) space charge layer, (6) diffusion layer, (7) contact to working electrode, (8) waveguide.

Checking the absence of internal mass transfer limitations is a more difficult task. A procedure that can be applied in the case of catalyst electrode films is the measurement of the open circuit potential of the catalyst relative to a reference electrode under fixed gas phase atmosphere (e.g. oxygen in helium) and for different thickness of the catalyst film. Changing of the catalyst potential above a certain thickness of the catalyst film implies the onset of the appearance of internal mass transfer limitations. Such checking procedures applied in previous electrochemical promotion studies allow one to safely assume that porous catalyst films (porosity above 20-30%) with thickness not exceeding 10pm are not expected to exhibit internal mass transfer limitations. The absence of internal mass transfer limitations can also be checked by application of the Weisz-Prater criterion (see, for example ref. 33), provided that one has reliable values for the diffusion coefficient within the catalyst film. 

Note that a number of complicating factors have been left out for clarity For instance, in the EMF equation, activities instead of concentrations should be used. Activities are related to concentrations by a multiplicative activity coefficient that itself is sensitive to the concentrations of all ions in the solution. The reference electrode necessary to close the circuit also generates a (diffusion) potential that is a complex function of activities and ion mobilities. Furthermore, the slope S of the electrode function is an experimentally determined parameter subject to error. The essential point, though, is that the DVM-clipped voltages appear in the exponent and that cheap equipment extracts a heavy price in terms of accuracy and precision (viz. quantization noise such an instrument typically displays the result in a 1 mV, 0.1 mV, 0.01 mV, or 0.001 mV format a two-decimal instrument clips a 345.678. .. mV result to 345.67 mV, that is it does not round up ... 78 to ... 8 ). 

Equilibrium electrode potentials are readily established when metal electrodes are in contact with melts. However, two difficnlties arise in attempts to measnre them suitable, sufficiently corrosion-resistant reference electrodes must be selected, and marked diffusion potentials develop at interfaces between different melts. 

The equation obtained can be used when the electrode potential can be varied independent of solution composition (i.e., when the electrode is ideally polarizable). For practical calculations we must change from the Galvani potentials, which cannot be determined experimentally, to the values of electrode potential that can be measured E = ( q + const (where the constant depends on the reference electrode chosen and on the diffusion potential between the working solution and the solution of the reference electrode). When a constant reference electrode is used and the working solutions are sufficiently dilute so that the diffusion potential will remain practically constant when their concentration is varied, dE (i(po and... 

In selecting reference electrodes for practical use, one should apply two criteria that of reducing the diffusion potentials and that of a lack of interference of RE components with the system being studied. Thus, mercury-containing REs (calomel or mercury-mercuric oxide) are inappropriate for measurements in conjunction with platinum electrodes, since the mercury ions readily poison platinum surfaces. Calomel REs are also inappropriate for systems sensitive to chloride ions. 

Figure 15.2 Schematic representation of different electrochemical cell types used in studies of electrocatalytic reactions (a) proton exchange membrane single cell, comprising a membrane electrode assembly (b) electrochemical cell with a gas diffusion electrode (c) electrochemical cell with a thin-layer working electrode (d) electrochemical cell with a model nonporous electrode. CE, counter-electrode RE, reference electrode WE, working electrode.

FIG. 1 Electrical potential oscillation across the nitrobenzene membrane and schematically illustrated features of the diffusion of yellowish substances in the U-shaped cell (a) potentiometer, (b) aqueous phase, (c) nitrobenzene phase, (d) KCl salt bridge, and (e) Ag/AgCl reference electrode. (Ref 4.)... 

Indicator electrodes, reference electrodes and diffusion potentials... 

In potentiometric measurements the simplest approach to the liquid-junction problem is to use a reference electrode containing a saturated solution of potassium chloride, for example the saturated calomel electrode (p. 177). The effect of the diffusion potential is completely suppressed if the solutions in contact contain the same indifferent electrolyte in a sufficient... 

In principle, different reference electrodes may be used if the cell is provided with a separate compartment and a Luggin capillary. But if the flow cell technique is to be applied, it is more convenient to avoid the use of capillaries where the solution cannot be easily exchanged. Active bulk components could diffuse through the capillary and give rise to erroneous responses. A small palladium gauze charged with hydrogen directly immersed in the solution can be used as the reference electrode (PdH ) [18]. 

In principle the ISO-NOP sensor works as follows. The sensor is immersed in a solution containing NO and a positive potential of —860 mV (vs Ag/AgCl reference electrode) is applied. NO diffuses across the gas permeable/NO-selective membrane and is oxidized at the working electrode surface producing a redox current. This oxidation proceeds via an electrochemical reaction followed by a chemical reaction. The electrochemical reaction is a one-electron transfer from the NO molecule to the electrode, resulting in the formation of the nitrosonium cation ... 

---