Process-based industries

It is also interesting to note that in two industry sectors respondents -Confectionery and Publishing - claimed to have no strategic objectives whatsoever and that 100% of their objectives were directed towards operational effectiveness. High levels for operational effectiveness objectives were recorded in virtually all of the process-based industry sectors Basic Chemicals (65%), Computer Hardware (85%), Confectionery (100%), Healthcare (76%), Power Water (81%), Telecommimications (69%), Retail Distribution (86%) and Retail Financial Services (84%). 

The reason for this was because it was felt, initially, that process-based industries would tend to have higher tool and technique usage requirements than project-based industries, and that manufacturing industries would also tend to have more need than service base industries, with combined industries somewhere in between. The rationale here was that manufacturing and process-based industries would tend to need more routinised and standardised approaches to business that would favour tool and technique usage across all four functions. On the other hand it was hypothesised that project-based and services related industries, with a more ad-hoc and less routinised approach to business, would use tools and techniques much less across all of the four functions. 

Manufacture and Processing. The industry related to iodine production began a few years after the discovery of the element by Courtois in 1811. The production processes are based on the raw materials containing iodine seaweeds, mineral deposits, and oh-weh or natural gas brines. 

Most commercial processes produce polypropylene by a Hquid-phase slurry process. Hexane or heptane are the most commonly used diluents. However, there are a few examples in which Hquid propylene is used as the diluent. The leading companies involved in propylene processes are Amoco Chemicals (Standard OH, Indiana), El Paso (formerly Dart Industries), Exxon Chemical, Hercules, Hoechst, ICl, Mitsubishi Chemical Industries, Mitsubishi Petrochemical, Mitsui Petrochemical, Mitsui Toatsu, Montedison, Phillips Petroleum, SheU, Solvay, and Sumimoto Chemical. Eastman Kodak has developed and commercialized a Hquid-phase solution process. BASE has developed and commercialized a gas-phase process, and Amoco has developed a vapor-phase polymerization process that has been in commercial operation since early 1980. 

Dehydrochlorination to Epoxides. The most useful chemical reaction of chlorohydrins is dehydrochlotination to form epoxides (oxkanes). This reaction was first described by Wurtz in 1859 (12) in which ethylene chlorohydria and propylene chlorohydria were treated with aqueous potassium hydroxide [1310-58-3] to form ethylene oxide and propylene oxide, respectively. For many years both of these epoxides were produced industrially by the dehydrochlotination reaction. In the past 40 years, the ethylene oxide process based on chlorohydria has been replaced by the dkect oxidation of ethylene over silver catalysts. However, such epoxides as propylene oxide (qv) and epichl orohydrin are stiU manufactured by processes that involve chlorohydria intermediates. 

Fibers produced from pitch precursors can be manufactured by heat treating isotropic pitch at 400 to 450°C in an inert environment to transform it into a hquid crystalline state. The pitch is then spun into fibers and allowed to thermoset at 300°C for short periods of time. The fibers are subsequendy carbonized and graphitized at temperatures similar to those used in the manufacture of PAN-based fibers. The isotropic pitch precursor has not proved attractive to industry. However, a process based on anisotropic mesophase pitch (30), in which commercial pitch is spun and polymerized to form the mesophase, which is then melt spun, stabilized in air at about 300°C, carbonized at 1300°C, and graphitized at 3000°C, produces ultrahigh modulus (UHM) carbon fibers. In this process tension is not requited in the stabilization and graphitization stages. 

The petroleum industry is now the principal suppHer of ben2ene, toluene, the xylenes, and naphthalene (see BTX processing Feedstocks). Petroleum displaced coal tar as the primary source for these aromatic compounds after World War II because it was relatively cheap and abundantly available. However, the re-emergence of king coal is predicted for the twenty-first century, when oil suppHes are expected to dwindle and the cost of producing chemicals from coal (including new processes based on synthesis gas) will gradually become more competitive (3). 

Extraction from Aqueous Solutions Critical Fluid Technologies, Inc. has developed a continuous countercurrent extraction process based on a 0.5-oy 10-m column to extract residual organic solvents such as trichloroethylene, methylene chloride, benzene, and chloroform from industrial wastewater streams. Typical solvents include supercritical CO9 and near-critical propane. The economics of these processes are largely driven by the hydrophihcity of the product, which has a large influence on the distribution coefficient. For example, at 16°C, the partition coefficient between liquid CO9 and water is 0.4 for methanol, 1.8 for /i-butanol, and 31 for /i-heptanol. 

Stable oxides, such as those of clrromium, vanadium and titanium cannot be reduced to the metal by carbon and tire production of these metals, which have melting points above 2000 K, would lead to a refractoty solid containing carbon. The co-reduction of the oxides widr iron oxide leads to the formation of lower melting products, the feno-alloys, and tlris process is successfully used in industrial production. Since these metals form such stable oxides and carbides, tire process based on carbon reduction in a blast furnace would appear to be unsatisfactory, unless a product samrated with carbon is acceptable. This could not be decarburized by oxygen blowing without significairt re-oxidation of the refractory metal. 

In 1838, Frederic Kuhlmann discovered die formation of nitrogen oxide (NO) during die catalytic oxidation of ammonia. Wilhelm Ostwald developed die production mediods in 1902 and established die base for today s major commercial processes. However, industrial production began only after Haber and Bosch developed the synthesis of ammonia around 1916. 

Progress in research and development in the wood-based industry and in the adhesive industry has shown many successes during the last decades. On the other hand, many industrial requirements still require considerable and important developments in this area. The main driving forces today are cheaper , quicker and more complex . The first two are caused by the heightened competition in the above-mentioned industries and the attempt to minimize costs while maintaining a certain level of product quality and performance. The key word more complex stands for new and specialized products and processes. Adhesives play a central role in wood-based panel production. The quality of bonding, and hence the properties of the wood-based panels, are determined mainly by the type and quality of the adhesive. Development in wood-based panels, therefore, is always linked to development in adhesives and resins. 

Thermal decomposition of LiR eliminates a /6-hydrogen atom to give an olefin and LiH, a process of industrial importance for long-chain terminal alkenes. Alkenes can also be produced by treatment of ethers, the organometallic reacting here as a very strong base (proton acceptor) ... 

---