Elastomer poly

As the demand for rubber increased so did the chemical industry s efforts to prepare a synthetic sub stitute One of the first elastomers (a synthetic poly mer that possesses elasticity) to find a commercial niche was neoprene discovered by chemists at Du Pont in 1931 Neoprene is produced by free radical polymerization of 2 chloro 1 3 butadiene and has the greatest variety of applications of any elastomer Some uses include electrical insulation conveyer belts hoses and weather balloons... 

Nitrile mbber finds broad application in industry because of its excellent resistance to oil and chemicals, its good flexibility at low temperatures, high abrasion and heat resistance (up to 120°C), and good mechanical properties. Nitrile mbber consists of butadiene—acrylonitrile copolymers with an acrylonitrile content ranging from 15 to 45% (see Elastomers, SYNTHETIC, NITRILE RUBBER). In addition to the traditional applications of nitrile mbber for hoses, gaskets, seals, and oil well equipment, new applications have emerged with the development of nitrile mbber blends with poly(vinyl chloride) (PVC). These blends combine the chemical resistance and low temperature flexibility characteristics of nitrile mbber with the stability and ozone resistance of PVC. This has greatly expanded the use of nitrile mbber in outdoor applications for hoses, belts, and cable jackets, where ozone resistance is necessary. 

Gun Propellents. Low sensitivity gun propeUants, often referred to as LOVA (low vulnerabUity ammunition), use RDX or HMX as the principal energy components, and desensitizing binders such as ceUulose acetate butyrate or thermoplastic elastomers (TPE) including poly acetal—polyurethane block copolymers, polystyrene—polyacrjiate copolymers, and glycidyl azide polymers (GAP) to provide the required mechanical... 

Butanediol. 1,4-Butanediol [110-63-4] made from formaldehyde and acetylene, is a significant market for formaldehyde representing 11% of its demand (115). It is used to produce tetrahydrofuran (THF), which is used for polyurethane elastomers y-butyrolactone, which is used to make various pyrroHdinone derivatives poly(butylene terephthalate) (PBT), which is an engineering plastic and polyurethanes. Formaldehyde growth in the acetylenic chemicals market is threatened by alternative processes to produce 1,4-butanediol not requiring formaldehyde as a raw material (140) (see Acetylene-derived chemicals). 

Diacyl peroxides are used in a broad spectmm of apphcations, including curing of unsaturated polyester resin compositions, cross-linking of elastomers, production of poly(vinyl chloride), polystyrene, and polyacrjlates, and in many nonpolymeric addition reactions. 

Applications. Among the P—O- and P—N-substituted polymers, the fluoroalkoxy- and aryloxy-substituted polymers have so far shown the greatest commercial promise (14—16). Both poly[bis(2,2,2-trifluoroethoxy)phosphazene] [27290-40-0] and poly(diphenoxyphosphazene) [28212-48-8] are microcrystalline, thermoplastic polymers. However, when the substituent symmetry is dismpted with a randomly placed second substituent of different length, the polymers become amorphous and serve as good elastomers. Following initial development of the fluorophosphazene elastomers by the Firestone Tire and Rubber Co., both the fluoroalkoxy (EYPEL-F) and aryloxy (EYPEL-A) elastomers were manufactured by the Ethyl Corp. in the United States from the mid-1980s until 1993 (see ELASTOLffiRS,SYNTHETic-PHOSPHAZENEs). 

Applications. Polymers with small alkyl substituents, particularly (13), are ideal candidates for elastomer formulation because of quite low temperature flexibiUty, hydrolytic and chemical stabiUty, and high temperature stabiUty. The abiUty to readily incorporate other substituents (ia addition to methyl), particularly vinyl groups, should provide for conventional cure sites. In light of the biocompatibiUty of polysdoxanes and P—O- and P—N-substituted polyphosphazenes, poly(alkyl/arylphosphazenes) are also likely to be biocompatible polymers. Therefore, biomedical appHcations can also be envisaged for (3). A third potential appHcation is ia the area of soHd-state batteries. The first steps toward ionic conductivity have been observed with polymers (13) and (15) using lithium and silver salts (78). 

Poly(alkylene glycol)s have a number of characteristics that make them desirable as lubricants. Compared to petroleum lubricants, they have lower pour points, a higher viscosity index, and a wider range of solubilities including water, compatibility with elastomers, less tendency to form tar and sludge, and lower vapor pressure (35). 

Noncrystalline aromatic polycarbonates (qv) and polyesters (polyarylates) and alloys of polycarbonate with other thermoplastics are considered elsewhere, as are aHphatic polyesters derived from natural or biological sources such as poly(3-hydroxybutyrate), poly(glycoHde), or poly(lactide) these, too, are separately covered (see Polymers, environmentally degradable Sutures). Thermoplastic elastomers derived from poly(ester—ether) block copolymers such as PBT/PTMEG-T [82662-36-0] and known by commercial names such as Hytrel and Riteflex are included here in the section on poly(butylene terephthalate). Specific polymers are dealt with largely in order of volume, which puts PET first by virtue of its enormous market volume in bottie resin. 

A. T. Chen, and co-workers, "Comparison of the Dynamic Properties of Polyurethane Elastomers Based on Low Unsaturation Polyoxypropylene Glycols and Poly(tetramethylene oxide) Glycols," Polyurethanes World Congress 1993, Vancouver, B.C., Canada, Oct. 10—13,1993. 

Properties have been determined for a series of block copolymers based on poly[3,3-bis(ethoxymethyl)oxetane] and poly [3,3-bis(methoxymethyl)oxetane]- (9-tetrahydrofuran. The block copolymers had properties suggestive of a thermoplastic elastomer (308). POX was a good main chain for a weU-developed smectic Hquid crystalline state when cyano- or fluorine-substituted biphenyls were used as mesogenic groups attached through a four-methylene spacer (309,310). Other side-chain Hquid crystalline polyoxetanes were observed with a spacer-separated azo moiety (311) and with laterally attached mesogenic groups (312). 

Pubhcations on curing polymers with TAIC include TEE—propylene copolymer (135), TEE—propylene—perfluoroaHyl ether (136), ethylene—chlorotrifluoroethylene copolymers (137), polyethylene (138), ethylene—vinyl acetate copolymers (139), polybutadienes (140), PVC (141), polyamide (142), polyester (143), poly(ethylene terephthalate) (144), sdoxane elastomers (145), maleimide polymers (146), and polyimide esters (147). 

Vinyl Acetate—Ethylene Copolymers. In these random copolymers, the ratio of ethylene to vinyl acetate (EVA) is varied from 30—60%. As the vinyl acetate content increases, the oil and heat resistance increases. With higher ethylene content the physical strength, tensile, and tear increases. The polymers are cured with peroxide. The main properties of these elastomers include heat resistance, moderate oil and solvent resistance, low compression set, good weather resistance, high damping, exceUent o2one resistance, and they can be easily colored (see Vinyl polymers, poly(VINYL acetate)). 

In addition, polyester polyols are made by the reaction of caprolactone with diols. Poly(caprolactone diols) are used in the manufacture of thermoplastic polyurethane elastomers with improved hydrolytic stabiHty (22). The hydrolytic stabiHty of the poly(caprolactone diol)-derived TPUs is comparable to TPUs based on the more expensive long-chain diol adipates (23). Polyether/polyester polyol hybrids are synthesized from low molecular weight polyester diols, which are extended with propylene oxide. 

VINYLIDENE POLYMERS, POLY(VINYLIDENE FLUORIDE) ELASTOMERS. 

Polymers account for about 3—4% of the total butylene consumption and about 30% of nonfuels use. Homopolymerization of butylene isomers is relatively unimportant commercially. Only stereoregular poly(l-butene) [9003-29-6] and a small volume of polyisobutylene [25038-49-7] are produced in this manner. High molecular weight polyisobutylenes have found limited use because they cannot be vulcanized. To overcome this deficiency a butyl mbber copolymer of isobutylene with isoprene has been developed. Low molecular weight viscous Hquid polymers of isobutylene are not manufactured because of the high price of purified isobutylene. Copolymerization from relatively inexpensive refinery butane—butylene fractions containing all the butylene isomers yields a range of viscous polymers that satisfy most commercial needs (see Olefin polymers Elastomers, synthetic-butylrubber). 

Many random copolymers have found commercial use as elastomers and plastics. For example, SBR (62), poly(butadiene- (9-styrene) [9003-55-8] has become the largest volume synthetic mbber. It can be prepared ia emulsion by use of free-radical initiators, such as K2S20g or Fe /ROOH (eq. 18), or in solution by use of alkyl lithium initiators. Emulsion SBR copolymers are produced under trade names by such companies as American Synthetic Rubber (ASPC), Armtek, B. F. Goodrich (Ameripool), and Goodyear (PHoflex) solution SBR is manufactured by Firestone (Stereon). The total U.S. production of SBR in 1990 was 581,000 t (63). 

Poly(butadiene- (9-acrylonitrile) [9008-18-3] NBR (64), is another commercially significant random copolymer. This mbber is manufactured by free-radical emulsion polymerization. Important producers include Copolymer Rubber and Chemical (Nysyn), B. F. Goodrich (Hycar), Goodyear (Chemigum), and Uninoyal (Paracdl). The total U.S. production of nitrile mbber (NBR) in 1990 was 95.6 t (65). The most important property of NBR mbber is its oil resistance. It is used in oil well parts, fuels, oil, and solvents (64) (see Elastomers, synthetic— nitrile rubber). 

The earliest study describing vulcanised polymers of esters of acryUc acid was carried out in Germany by Rohm (2) before World War I. The first commercial acryUc elastomers were produced in the United States in the 1940s (3—5). They were homopolymers and copolymers of ethyl acrylate and other alkyl acrylates, with a preference for poly(ethyl acrylate) [9003-32-17, due to its superior balance of properties. The main drawback of these products was the vulcanisation. The fully saturated chemical stmcture of the polymeric backbone in fact is inactive toward the classical accelerators and curing systems. As a consequence they requited the use of aggressive and not versatile compounds such as strong bases, eg, sodium metasiUcate pentahydrate. To overcome this limitation, monomers containing a reactive moiety were incorporated in the polymer backbone by copolymerisation with the usual alkyl acrylates. 

---