Alkyl- Lithium Initiator

With the assumption that association is high and the concentration of the monomeric species is low, the concentration of the monomeric species is given by Eq. (10), where P-Li is either the initiating lithium alkyl or the propagating species. 

The difficulties encountered in the early studies of anionic polymerization of methyl methacrylate arose from the unfortunate choice of experimental conditions the use of hydrocarbon solvents and of lithium alkyl initiators. The latter are strong bases. Even at —60 °C they not only initiate the conventional vinyl poly-addition, but attack also the ester group of the monomer yielding a vinyl ketone1, a very reactive monomer, and alkoxide 23). Such a process is described by the scheme. 

The mechanism of anionic polymerization of styrene and its derivatives is well known and documented, and does not require reviewing. Polymerization initiated in hydrocarbon solvents by lithium alkyls yields dimeric dormant polymers, (P, Li)2, in equilibrium with the active monomeric chains, P, Li, i.e. 

Tertiary amines also depolymerize lithium alkyl tetramers and hexamers and can be used to trigger reactions with alkyl halides (Lepley, 1968). However, when triethylamine is used to initiate the butyl... 

The activity of transition metal allyl compounds for the polymerization of vinyl monomers has been studied by Ballard, Janes, and Medinger (10) and their results are summarized in Table II. Monomers that polymerize readily with anionic initiators, such as sodium or lithium alkyls, polymerize vigorously with allyl compounds typical of these are acrylonitrile, methyl methacrylate, and the diene isoprene. Vinyl acetate, vinyl chloride, ethyl acrylate, and allylic monomers do not respond to these initiators under the conditions given in Table II. 

The most studied catalyst family of this type are lithium alkyls. With relatively non-bulky substituents, for example nBuLi, the polymerization of MMA is complicated by side reactions.4 0 These may be suppressed if bulkier initiators such as 1,1-diphenylhexyllithium are used,431 especially at low temperature (typically —78 °C), allowing the synthesis of block copolymers.432,433 The addition of bulky lithium alkoxides to alkyllithium initiators also retards the rate of intramolecular cyclization, thus allowing the polymerization temperature to be raised.427 LiCl has been used to similar effect, allowing monodisperse PMMA (Mw/Mn = 1.2) to be prepared at —20 °C.434 Sterically hindered lithium aluminum alkyls have been used at ambient (or higher) temperature to polymerize MMA in a controlled way.435 This process has been termed screened anionic polymerization since the bulky alkyl substituents screen the propagating terminus from side reactions. 

An unusual mixed lithium phosphide/lithium alkyl aggregate has been reported as arising from an attempted synthesis of Li PH(mes ) (46). Initial treatment of phosphorus trichloride with Li(mes ) is reported to give a mixture of the desired product, (mes )PCl2, and the side product (mes )Cl (via Li/Cl exchange) in an approximately 2 1 ratio. Reduction of this mixture with LiAlH4, followed by treatment with BuLi, then leads to rapid formation of Li PH(mes ), accompa-... 

In a further effort to identify the active intermediate that initiates the reaction, they tested the effect of a few possible ingredients on the production of EMC based on the knowledge about the chemical composition of the SEI on carbonaceous anodes. These model compounds included Li2C03, LiOCHs, and LiOH, while lithium alkyl carbonate was not tested due to its instability and therefore rare avail-ability. The results unequivocally showed that LiOCHs effectively catalyzes the ester exchange. 

On the basis of the above observation, Dahn and co-workers proposed a thermal reaction scheme for the coupling of carbonaceous anodes and electrolytes. The initial peak, which was almost identical for all of the anode samples and independent of lithiation degrees, should arise from the decomposition of the SEI because the amount of SEI chemicals was only proportional to the surface area. This could have been due to the transformation of the metastable lithium alkyl carbonate into the stable Li2C03. After the depletion of the SEI, a second process between 150 and 190 °C was caused by the reduction of electrolyte components by the lithiated carbon to form a new SEI, and the autocatalyzed reaction proceeded until all of the intercalated lithium was consumed or the thickness of this new SEI was sufficient to suppress further reductions. The corresponding decrease in SHR created the dip in the least lithiated sample in Eigure 35. Above 200 °C (beyond the ARC test range as shown in Eigure 35), electrolyte decomposition occurred, which was also an exothermic process. 

Irreversible Capacity. Because an SEI and surface film form on both the anode and cathode, a certain amount of electrolyte is permanently consumed. As has been shown in section 6, this irreversible process of SEI or surface layer formation is accompanied by the quantitative loss of lithium ions, which are immobilized in the form of insoluble salts such as Li20 or lithium alkyl carbonate. Since most lithium ion cells are built as cathode-limited in order to avoid the occurrence of lithium metal deposition on a carbonaceous anode at the end of charging, this consumption of the limited lithium ion source during the initial cycles results in permanent capacity loss of the cell. Eventually the cell energy density as well as the corresponding cost is compromised because of the irreversible capacities during the initial cycles. 

Nucleophilic reagents attack pyridine at the a-position to form an adduct that rearomatizes by dissociation (Scheme 1). Only very strong nucleophiles, e.g. NH2-, RLi, LAH, Na-NH3, react, and for the second step to afford a substitution product (5), conditions that favour hydride loss are required. Adducts formed with hydride ions (from LAH) or carbanions (from lithium alkyls) are relatively more stable than the others at low temperature, and dihydropyridines (6) can be obtained by careful neutralization. Fusion of a benzene ring to pyridine increases reactivity towards nucleophiles, and attack is now found at both a- and y-positions in quinoline (7) and at C-l in isoquinoline (8). This may be attributed to a smaller loss of aromaticity in forming the initial adduct than in pyridine, and thus a correspondingly decreased tendency to rearomatize is also observed. Acridine reacts even more easily, but nucleophilic attack is now limited to the y -position (9), as attachment of nucleophiles at ring junctions is very rare. 

In addition, hydroxyl polymers prepared by use of lithium alkyl acetal initiators have shown a high degree of functional purity (Table II). The functionality data for XI is a bit low, in part, because a linear GPC calibration was used to calculate nn (GPC). It should also be noted that Equations 1-9 proceed in the absence of anionic association or gel. 

Organolithum compounds (lithium alkyls) are the most valuable initiators in anionic polymerization.120168 169172-175 Since living anionic polymerization requires the fastest possible initiation, sec- or ferf-butyllithium is usually used. Lithium alkyls add readily to the double bond of styrene [Eq. (13.32)] or conjugated dienes and form free ions or an ion pair depending on the solvent ... 

Metallic lithium in the form of a suspension has been used to polymerize isoprene (97) but the system is not too suitable for an exact analysis of the mechanism. The conversion-time curves are sigmoidal in shape. Minoux (66) has shown that the overall rate is not very dependent on the amount of lithium dispersion used as expected if the organo-lithium intermediates are highly associated. The molecular weight of the polymer is more dependent on quantity of lithium used. The observed kinetic behaviour is very similar to that shown in lithium alkyl initiation. This suggests that apart from differences in the initiation step, the mechanisms are quite similar. 

Copolymerizations initiated by lithium metal should give the same product as produced from lithium alkyls. Usually the radical ends produced by electron transfer initiation have so short a lifetime they can have no influence on the copolymerization. This is true for instance in the copolymerization of isoprene and styrene (50). The product is identical if initiated by lithium metal or by butyllithium. With the styrene-methylmethacrylate system, however, differences are observed (79,80,82). Whereas the butyllithium initiated copolymer contains no styrene at low conversions, the one initiated by lithium metal has a high styrene content if the reaction is carried out in bulk and a moderate one even in tetrahydrofuran. These facts led O Driscoll and Tobolsky (80) to suggest that initiation with lithium occurs by electron exchange and that in this case the radical ends are sufficiently long-lived to produce simultaneous radical and anionic reactions at opposite ends of the chain. Only in certain rather exceptional circumstances would the free radical reaction be of importance. Some of the conditions required have been discussed by Tobolsky and Hartley (111). The anionic reaction should be slow. This is normally true for lithium based catalysts in hydrocarbon solvents. No evidence of appreciable radical participation is observed for initiation by sodium and potassium. The monomers should show a fast radical reaction. If styrene is replaced by isoprene, no isoprene is found in the copolymer for isoprene polymerizes slowly by free radical initiation. Most important of all, initiation should be slow to produce a low steady concentration of radical-anions. An initiator which produces an almost instantaneous and complete electron transfer to monomer produces a high radical concentration which will ensure their rapid mutual termination. 

COLEMAN and Fox (18) have pointed out that the non Bernoullian sequence distribution observed in some of these systems can be formed without the hypothesis of penultimate effects. All that is required is that two or more types of active species be present which do not rapidly interconvert. Each can add monomer at its own rate and with its own characteristic regulating effect. No penultimate effect is necessary but the sequence distribution will be non-Bernoullian. This type of mechanism is particularly attractive in the explanation of stereoblock polymer formation in the lithium alkyl systems in toluene with small amounts of ether present. The presence of at least two species of active centres has been inferred from an examination of polymer fractions obtained from butyllithium initiated polymerizations (19) in toluene. The change in molecular weight distribution with time suggests the presence of two... 

Some information is available on other acrylates. N,N-disubstituted acrylamides form isotactic polymers with lithium alkyls in hydrocarbons (12). t-Butylacrylate forms crystallizable polymers with lithium-based catalysts in non-polar solvents (65) whereas the methyl, n-butyl, sec-butyl and isobutyl esters do not. Isopropylacrylate also gives isotactic polymer with lithium compounds in non-polar solvents (34). The inability of n-alkylacrylates to form crystallizable polymers may result from a requirement for a branched alkyl group for stereospecific polymerization. On the other hand lack of crystallizability cannot be taken as definite evidence of a lack of stereoregulating influence, as sometimes quite highly regular polymer fails to crystallize. The butyllithium-initiated polymers of methylmethacrylate for instance cannot be crystallized. The presence of a small amount of more random structure appears to inhibit the crystallization process1. 

The reaction of benzo[A]-l,3-diazasilole 85 with lithium alkyls yields the insertion product 112. It was suggested that the initial step of this reaction is the formation of the donor-acceptor complex 113 (Scheme 10) <2002JOM272, 2002JOM150>. The tetracoordinated silicon compounds 112 might have synthetic potential as silylene transfer reagents. 

The unique feature of the alkyllithium compounds that makes them useful as diene initiators is their character as exceedingly powerful bases yet they are soluble in organic solvents and quite thermally stable. Alkyllithium compounds are sufficiently basic to add to hydrocarbon monomers. However, lithium salts of stabilized anions, such as acetylide and fluorenyl anions, are too weakly basic to add to such double bonds. Similarly, alkoxides and mercaptides fail to react with hydrocarbon monomers, but lithium alkyl amides react analogously to alkyllithium compounds. 

When lithium alkyl catalysts are used in non-solvating media such as aliphatic hydrocarbons, the polymer-lithium bond is not sufficiently ionic to initiate anionic polymerization so that the monomer must first complex with vacant orbitals in the lithium. A partial positive charge is induced on the monomer in the complex, and this facilitates migration of the polymer anion to the most electrophilic carbon of the complexed monomer. This type of polymerization is more appropriately termed coordinated anionic and will be discussed in the next section. There does not appear to be any evidence that alkyl derivatives of metals which are less electropositive than lithium and magnesium can initiate simple anionic polymerization. 

In lithium alkyl-initiated polymerizations only chain initiation and propagation steps need be considered in hydrocarbon solvents. Both reactions are strongly influenced by extensive association of all lithium compounds. The reactive species in chain propagation is the small amount of dissociated material which probably exists as an ion pair. Association phenomena disappear on adding small amounts of polar additives, and the aggregates are replaced by solvated ion pairs. In polar solvents of relatively high dielectric constant (e.g. tetrahydrofuran), some dissociation of the ion pairs to free ions occurs, and both species contribute to the propagation step. The polymerizations are often complicated in tetrahydrofuran by two side reactions, namely carbanion isomerization and reaction with the solvent. 

The general characteristics of these polymerizations are those of the so-called living polymer (24). Under suitable conditions every lithium alkyl molecule will initiate one chain, and there is no evidence for chain transfer or termination 14, 27). The molecular weight distributions will be narrow— Mw/Mn of 1.3 or less according to the relative rates of chain initiation and... 

In benzene solution, measurements have been made of the rate of reaction of butyllithium with styrene (27), l l-diphenylethylene (6), and with fluorene (7). In each case the reaction was first order in olefin and close to one-sixth order in butyllithium. This latter, fractional order has been attributed to the sixfold association of lithium alkyls in hydrocarbon solution. The actual species active in initiation is the monomeric butyllithium in equilibrium with the hexamer. 

The radical model cannot be applied for ionic and coordination polymerizations. With a few exceptions, termination by mutual combination of active centres does not occur. The only possibility is to measure the rate of each copolymerization independently. The situation can be greatly simplified for copolymerizations in living systems. The constants ku and k22 can usually be measured easily in homopolymerizations. Also, the coaddition constants fc12 or k2] are often directly accessible when the M] and M2 active centres can be differentiated spectroscopically or when the rate of monomer M2 (M[) consumption at M] M 2 centres can be measured. Ionic equibria, association, polarity of medium and solvation must be respected, even when their quantitative effect is not known exactly. The unusual situations confronting macromolecular chemistry will be demonstrated by the example of the anionic copolymerization of styrene with butadiene initiated by lithium alkyls in hydrocarbon medium. 

Since shortly after its discovery by Szwarc et al. [5] in the mid-1950s, living anionic polymerization has been recognized as an ideal route to styrenic block copolymers [6]. To date, living anionic polymerization remains the only commercially important technology for SBC synthesis. The anionic polymerization of styrene and common dienes such as butadiene and isoprene satisfies the criteria outlined above, particularly when carried out in a hydrocarbon solvent and initiated by an appropriate lithium alkyl. 

---