Plastics polyurethane foam

To demonstrate the fungistatic activity in another type of plastic polyurethane foams, equipped with different concentrations of OIT, have been investigated. Results of the NSA test on those samples are listed in table 2. 

Blowing agents for plastics, polyurethane foams as Freon substitutes. For example, t.butyl methyl pyrocarbonate (R = methyl, R = t. butyl) was claimed as a foaming agent added during processing of polymers to achieve a cellular structure by liberation of carbon dioxide (Ref. 40). 

Due to the special features mentioned above, siloxane amphiphiUc copolymers are used in a wide variety of applications including foam stabilization in plastic (polyurethane) foams, cosmetics, wetting, emulsification, lubrication and in antistatic agents, drug delivery and so forth. 

Composite materials Photochromic glasses Fillers and pigments Butter, margarine Opal Expanded plastics (polyurethane foams)... 

About 2 X 10 Ib/year of 1 2 epoxypropane is produced in the United States as an intermediate in the preparation of various polymeric materials including polyurethane plastics and foams and polyester resins A large fraction of the 1 2 epoxypropane is made from propene by way of its chlorohydrm... 

Fig. 2ab. Photomicrographs of foam cell stmcture (a) extmded polystyrene foam, reflected light, 26 x (b) polyurethane foam, transmitted light, 26 x (c) polyurethane foam, reflected light, 12 x (d) high density plastic foam, transmitted light, 50x (22).

Electrical Properties. CeUular polymers have two important electrical appHcations (22). One takes advantage of the combination of inherent toughness and moisture resistance of polymers along with the decreased dielectric constant and dissipation factor of the foamed state to use ceUular polymers as electrical-wire insulation (97). The other combines the low dissipation factor and the rigidity of plastic foams in the constmction of radar domes. Polyurethane foams have been used as high voltage electrical insulation (213). 

Commercial Construction. The same attributes desirable on residential constmction appHcations hold for commercial constmction as weU but insulation quaHty, permanence, moisture insensitivity, and resistance to free2e—thaw cycling in the presence of water are of greater significance. For this reason ceUular plastics have greater appHcation here. Both polystyrene and polyurethane foams are highly desirable roof insulations in commercial as in residential constmction. 

The insulating value and mechanical properties of rigid plastic foams have led to the development of several novel methods of buUding constmction. Polyurethane foam panels may be used as unit stmctural components (220) and expanded polystyrene is employed as a concrete base in thin-sheU constmction (221). 

Polyols. Several important polyhydric alcohols or polyols are made from formaldehyde. The principal ones include pentaerythritol, made from acetaldehyde and formaldehyde trimethylolpropane, made from -butyraldehyde and formaldehyde and neopentyl glycol, made from isobutyraldehyde and formaldehyde. These polyols find use in the alkyd resin (qv) and synthetic lubricants markets. Pentaerythritol [115-77-5] is also used to produce rosin/tall oil esters and explosives (pentaerythritol tetranitrate). Trimethylolpropane [77-99-6] is also used in urethane coatings, polyurethane foams, and multiftmctional monomers. Neopentyl glycol [126-30-7] finds use in plastics produced from unsaturated polyester resins and in coatings based on saturated polyesters. 

Another area ia which 1,4-cyclohexanedimethanol is commercially important is ia the manufacture of polyurethane foams (see Eoamed plastics). 

Foamed plastics (qv) were developed in Europe and the United States in the mid-to-late 1930s. In the mid-1940s, extmded foamed polystyrene (XEPS) was produced commercially, foUowed by polyurethanes and expanded (molded) polystyrene (EPS) which were manufactured from beads (1,2). In response to the requirement for more fire-resistant ceUular plastics, polyisocyanurate foams and modified urethanes containing additives were developed in the late 1960s urea—formaldehyde, phenoHc, and other foams were also used in Europe at this time. 

A. H. Landrock, Polyurethane Foams Technology Properties and Applications, Report 37, Plastic Technical Evaluation Center, Picatiuny Arsenal, Dover, N.J., 1969. 

Ammonia is used in the fibers and plastic industry as the source of nitrogen for the production of caprolactam, the monomer for nylon 6. Oxidation of propylene with ammonia gives acrylonitrile (qv), used for the manufacture of acryHc fibers, resins, and elastomers. Hexamethylenetetramine (HMTA), produced from ammonia and formaldehyde, is used in the manufacture of phenoHc thermosetting resins (see Phenolic resins). Toluene 2,4-cHisocyanate (TDI), employed in the production of polyurethane foam, indirectly consumes ammonia because nitric acid is a raw material in the TDI manufacturing process (see Amines Isocyanates). Urea, which is produced from ammonia, is used in the manufacture of urea—formaldehyde synthetic resins (see Amino resins). Melamine is produced by polymerization of dicyanodiamine and high pressure, high temperature pyrolysis of urea, both in the presence of ammonia (see Cyanamides). 

The plastic sandwich roof is made from rigid polyurethane foam panels sandwiched inside a plastic coating. 

Another compound, the antimicrobial action of which is associated with chelation, is 2-pyridinethiol-A/-oxide [3811-73-2] (Omadine). Activity has been shown to depend on coordinating property. The iron chelate is active, but not the free pyridine compound (200). In the form of its zinc chelate it is found in shampoos to control seborrheic dermatitis (201). Other appHcations of this useful chemical include preservation of adhesives, plastics, latex paints, polyurethane foam, and metal working fluids (202). 

The main uses of toluene are as a solvent in paints, rubber, and plastic cements and as a feedstock in the manufacture of organic chemicals, explosives, detergents, and polyurethane foams. Xylenes (which exist as three isomers) are used in the manufacture of DMT, alkyd resins, and plasticizers. Naphthalene is mainly used in the manufacture of dyes, pharmaceuticals, insect repellents, and phthalic anhydride (used in the manufacture of alkyd resins, plasticizers, and polyester). 

To meet the 2001 U.S. energy standards and the 2003 phase-out of HCFCs, there is a great incentive to develop a significantly better thermal insulation. The most dramatic approach would use vacuum panels for insulating the cabinet. A number of U.S. and Japanese manufacturers have developed such panels and placed these kinds of refrigerators in homes. The panels consist of multilayer plastic envelopes filled with precipitated (fumed) silica. The claimed thermal conductivity is one-fourth that of polyurethane foam. The two major obstacles are cost and the maintenance of vacuum for twenty years. 

Glycerol, a trihydric alcohol, is used to produce polyurethane foams and alkyd resins. It is also used in the manufacture of plasticizers. 

Different core materials are used. They include foam, honeycomb core (plastic, paper, aluminum, etc.), ribs, balsa wood, filler spacers, corrugated sheet spacers, etc. Materials such as polyurethane foam, cellulosic foams, and polystyrene foams are widely used as core materials. Plastics, such as glass-reinforced polyester, are frequently used as the skins for panels. Different skin materials are used such as metallic skins alone or in conjunction with plastic skins. 

One example is the use of rigid selfexpanding closed cell polyurethane foams as a method to inhibit corrosion of the interior surfaces of metal (steel, etc.) structural cavities exposed to seawater and moisture is one of many example of plastic providing corrosion protection. Unfilled metal cavities are a general feature of various structures or products used in the marine, building, electronics,... 

Most rigid polyurethane foams have a closed cell structure. Closed cells form when the plastic cell walls remain intact during the expansion process and are not ruptured by the increasing cell pressure. Depending on the blowing process a small fraction (5-10%) of the cells remain open. Closed cell structures provide rigidity and obstruct gaseous or fluid diffusional processes. 

This low pressure process, also known as elastic reservoir molding, consists of making basically a sandwich of plastic-impregnated open-celled flexible polyurethane foam between the face layers of fibrous reinforcements. When this plastic composite is placed in a mold and squeezed, the foam is compressed, forcing the plastic outward and into the reinforcement. The elastic foam exerts sufficient pressure to force the plastic-impregnated reinforcement into contact with the heated mold surface. Other plastics are used. 

SCRIMP process This Seeman Composites Resin Infusion Process (SCRIMP) is described as a gas-assist resin transfer molding process. As an example glass fiber fabrics/ thermoset vinyl ester polyester plastic and polyurethane foam panels (for insulation) are placed in a segmented tool. A vacuum is pulled with a bag so that a huge amount of plastic can be drawn into the mold (Marco process approach). Its curved roof is made separately and bonded to the box with mechanical and adhesive fastening. It is similar to various reinforced plastics molding processes. 

Disposal of Plastics with Emphasis on Foam-in-Place Polyurethane Foam , PLASTEC Rept R37A (1973) 39) J.B. Titus, Environmental-... 

Due to low hydrolytic and chemical resistance and to low melting point, aliphatic polyesters have long been considered to be limited to applications such as plasticizers or macromonomers for the preparation of polyurethane foams, coatings, or... 

---