Of cyclohexanone

Cyclohexanone oxime. Add 20 g. (21 ml.) of cyclohexanone to a solution of 17 g. of hydroxylamine hydrochloride in 40 ml. of water, and cool the mixture in ice-water. Add a solution of 13 g. of anhydrous sodium carbonate in 40 ml. of water slowly to the mixture, stirring the latter with a 100° thermometer, and maintaining the temperature of the mixture at 20-25° meanwhile. The oxime rapidly separates. Stir the complete mixture at intervals, and after 10 minutes filter the oxime at the pump, drain thoroughly and dry it in a (vacuum) desiccator. Yield of crude oxime, 20 g. Recrystallise from petroleum (b.p. 100-120 ) and dry over paraffin wax (p. 19). Yield of pure oxime, 16 g., m.p. 88°. 

Dissolve 8 8 g. (9 0 ml.) of cyclohexanone in 50 ml. of glacial acetic acid, add 8 ml. of phenylhydrazine, and boil the solution under reflux for 5 minutes. Cool the solution, when the tetrahydrocarbazole will crystallise out. Filter at the pump, drain well, and recrystallise either from aqueous ethanol or (better) from aqueous acetic acid. The recrystallisation should be performed rapidly, for the tetrahydrocarbazole undergoes atmO" spheric oxidation in hot solutions after recrystallisation, the compound should be dried in a vacuum desiccator and not in an oven. Repeated recrystallisation should be avoided. The tetrahydrocarbazole, after thorough drying, is obtained as colourless crystals, m.p. 118° yield of recrystallised material, 11 g. 

Dissolve 2 5 g. of hydroxylamine hydrochloride and 4 g. of crystallised sodium acetate in 10 ml. of water in a small flask or in a test-tube. Warm the solution to about 40° and add 2 5 g. of cyclohexanone. Stopper the vessel securely with a cork and shake vigorously for a few minutes the oxime soon separates as a crystalline solid. Cool in ice, filter the crystals at the pump, and wash with a little cold water. RecrystaUise from light petroleum, b.p. 60-80°, and dry the crystals upon filter paper in the air. The yield of pure cycZohexanone oxime, m.p. 90°, is 2 -5 g. 

An interesting application is the preparation of 1 2 3 4-tetrahydrocarb azole (VI), which is formed when phenylhydrazine is added to a boiling aolutiai of cyclohexanone in acetic acid the plienylhydrazone (V) Intermediately produced undergoes ring closure directly ... 

Acetone in conjunction with benzene as a solvent is widely employed. With cyclohexanone as the hydrogen acceptor, coupled with toluene or xylene as solvent, the use of higher reaction temperatures is possible and consequently the reaction time is considerably reduced furthermore, the excess of cyclohexanone can be easily separated from the reaction product by steam distillation. At least 0 25 mol of alkoxide per mol of alcohol is used however, since an excess of alkoxide has no detrimental effect 1 to 3 mols of aluminium alkoxide is recommended, particularly as water, either present in the reagents or formed during secondary reactions, will remove an equivalent quantity of the reagent. In the oxidation of steroids 50-200 mols of acetone or 10-20 mols of cyclohexanone are generally employed. 

Enamines derived from ketones are allylated[79]. The intramolecular asymmetric allylation (chirality transfer) of cyclohexanone via its 5-proline ally ester enamine 120 proceeds to give o-allylcyclohexanone (121) with 98% ee[80,8l]. Low ee was observed in intermolecular allylation. Similarly, the asymmetric allylation of imines and hydrazones of aldehydes and ketones has been carried out[82]. 

Enamines as nucleophiles react with butadiene, and a-octadienyl ketones or aldehydes are obtained after hydrolysis[57]. This is a good way of introducing an octadienyl group at the o-position of ketones or aldehydes, because butadiene does not react with ketones or aldehydes directly. The reaction of the pyrrolidine enamine of cyclohexanone gives, after hydrolysis, 2-(2,7-octadie-nyOcyclohe.xanone (58) as the main product, accompanied by a small amount of 2,6-di(2,7-octadienyl)cyclohexanone. The reaction of the optically active enamine 59 with butadiene gave 2-(2,7-octadienyl)cyclohexanone (60) in 72% ce[58]. 

The product (6 hexanohde) is a cyclic ester or lactone (Section 19 15) Like the Baeyer-Vilhger oxidation an oxygen atom is inserted between the carbonyl group and a carbon attached to it But peroxy acids are not involved m any way the oxidation of cyclohexanone is catalyzed by an enzyme called cyclohexanone monooxygenase with the aid of certain coenzymes... 

Construct a molecular model of cyclohexanone Do either of the hydrogens of C 2 eclipse the carbonyl oxygen" ... 

Adipic acid (qv) has a wide variety of commercial uses besides the manufacture of nylon-6,6, and thus is a common industrial chemical. Many routes to its manufacture have been developed over the years but most processes in commercial use proceed through a two-step oxidation of cyclohexane [110-83-8] or one of its derivatives. In the first step, cyclohexane is oxidized with air at elevated temperatures usually in the presence of a suitable catalyst to produce a mixture of cyclohexanone [108-94-1] and cyclohexanol [108-93-0] commonly abbreviated KA (ketone—alcohol) or KA oil ... 

Reductive amination of cyclohexanone using primary and secondary aHphatic amines provides A/-alkylated cyclohexylamines. Dehydration to imine for the primary amines, to endocycHc enamine for the secondary amines is usually performed in situ prior to hydrogenation in batch processing. Alternatively, reduction of the /V-a1ky1ani1ines may be performed, as for /V,/V-dimethy1 cyclohexyl amine from /V, /V- di m e th y1 a n i1 i n e [121 -69-7] (12,13). One-step routes from phenol and the alkylamine (14) have also been practiced. 

DCHA is normally obtained in low yields as a coproduct of aniline hydrogenation. The proposed mechanism of secondary amine formation in either reductive amination of cyclohexanone or arene hydrogenation iHurninates specific steps (Fig. 1) on which catalyst, solvents, and additives moderating catalyst supports all have effects. 

PUtzing erReaction. Quinoline-4-carboxyhc acids are easily prepared by the condensation of isatin [91-56-5] (16) with carbonyl compounds (50). The products may be decarboxylated to the corresponding quinolines. The reaction of isatin with cycHc ketones has been reported, eg, the addition of cyclohexanone gives the tricycHc intermediate (17) [38186-54-8] which upon oxidation produces quinoline-2,3,4-tricarboxyhc acid [16880-83-4] (51). 

BASF. In the Badische process, cyclohexanone is produced by Hquid-phase catalytic air oxidation of cyclohexane to KA oil, which is a mixture of cyclohexanone and cyclohexanol, and is followed by vapor-phase catalytic dehydrogenation of the cyclohexanol in the mixture. Overall yields range from 75% at 10% cyclohexane conversion to 80% at 5% cyclohexane conversion. 

The most important use of cyclohexanone is as a chemical intermediate in nylon manufacture 97% of all cyclohexanone output is used either to make caprolactam for nylon-6, or adipic acid for nylon-6,6. In the caprolactam process cyclohexanone is converted to cyclohexanone oxime (mp,... 

Table 3. Estimated U.S. Annual Production Capacity of Cyclohexanone...

Cyclohexanol can be deterrnined colorimetricaHy by reaction with -hydroxy-ben2aldehyde in sulfuric acid (18). This method can be used in the presence of cyclohexanone and cyclohexane. Cyclohexanol and cyclohexanone both show a maximum absorbency at 535 nm but at 625 nm the absorption by cyclohexanone is negligible, whereas cyclohexanol shows appreciable absorption. 

The reaction of vinylogous amides, or ketoaldehydes, with hydroxylamine produced 4,5,6,7-tetrahydro-l,2-benzisoxazole. A side product is the 2,1-benzisoxazole (Scheme 173) (67AHC(8)277). The ring system can also be prepared by the reaction of cyclohexanone enamines with nitrile oxides (Scheme 173) (78S43, 74KGS901). Base treatment produced ring fission products and photolysis resulted in isomerization to benzoxazoles (76JOC13). 

Clean examples of diaziridine to hydrazone rearrangements are rare. Diaziridine (119) mentioned above rearranges to the isomeric enhydrazone in boiling toluene, and 2,4-dinitrophenyldiaziridine (125) under the same conditions affords the 2,4-dinitrophenylhy-drazone (145) within 4 h. On blocking this rearrangement by iV-methyl, conversion with loss of cyclohexanone occurred to give benzotriazole iV-oxide (146) (72JOC2980). 

Analogous complexes are formed between l,2-diazaspiro[2.5]oct-l-ene (189) and the Ru(NH3)s cation in a 1 1 or 1 2 ratio. An X-ray analysis of the 1 1 complex (189a) gives evidence of a nitrogen-metal bond. Oxidation converts the 1 1 complex to the known dinitrogen complex (190) by liberation of cyclohexanone (80MI50800). 

Hydroxymethylmethyldiazirine (209 unprotonated) formed propionaldehyde as the sole product by thermal nitrogen extrusion 4-hydroxy-l,2-diazaspiro[2.5]oct-l-ene (218) formed a mixture of cyclohexanone (73%), cyclohexenol (21%) and cyclohexene oxide (5%). Thermal decomposition of difluorodiazirine (219) was investigated intensively. In this case there is no intramolecular stabilization possible. On heating for three hours to 165-180 °C hexafluorocyclopropane and tetrafluoroethylene were formed together with perfluorofor-maldazine 64JHC59). 

Particular reactions can occur in either or both phases or near the interface. Nitration of aromatics with HNO3-H2SO4 occurs in the aqueous phase (Albright and Hanson, eds.. Industrial and Laboratoiy Nitration.s, ACS Symposium Series 22 [1975]). An industrial example of reaction in both phases is the oximation of cyclohexanone, a step in the manufacture of caprolactam for nylon (Rod, Proc. 4th Interna-tional/6th European Symposium on Chemical Reactions, Heidelberg, Pergamon, 1976, p. 275). The reaction between butene and isobutane... 

SEMMLER WOLFF SCHROETER OximeAromatizatlon Aramatization of cyclohexanone oximes to anilines... 

Cyalohexylideneaaetonit ri-le. A 1-L three-necked, round-bottomed flask equipped with a reflux condenser, mechanical stirrer and addition funnel, is charged with potassium hydroxide (855 pellets, 33.0 g, 0.5 mol. Note 1) and acetonitrile (250 ml. Notes 2 and 3). The mixture is brought to reflux and a solution of cyclohexanone (49 g, 0.5 mol. Note 4) in acetonitrile (100 mL) is added over a period of 0.5-1.0 hr. Heating at reflux is continued for 2 hr (Note 5) after the addition is complete and the hot solution is then poured onto cracked ice (600 gl. The resulting binary mixture is separated... 

Typically, the reaetion would be carried out at 140°C in white spirit with potassium carbazole as a catalyst. Davidge ° has reported problems in polymerisation of V-vinyl carbazole prepared from carbazole obtained from coal tar, attributing this to the presence of sulphur. To overcome these problems carbazole has been prepared synthetically by reactions of cyclohexanone with... 

The conversion of cyclohexanone to cyclohexanone oxime is brought about by the use of hydroxylamine sulphate. The sulphuric acid is neutralised with ammonia to ammonium sulphate and this is separated from the oxime. In the presence of oleum the oxime undergoes the process known as the Beckmann rearrangement to yield the crude caprolactam. After further neutralisation with ammonia the caprolactam and further ammonium sulphate are separated by solvent extraction (Figure 18.7). 

A route to phenol has been developed starting from cyclohexane, which is first oxidised to a mixture of cyclohexanol and cyclohexanone. In one process the oxidation is carried out in the liquid phase using cobalt naphthenate as catalyst. The cyclohexanone present may be converted to cyclohexanol, in this case the desired intermediate, by catalytic hydrogenation. The cyclohexanol is converted to phenol by a catalytic process using selenium or with palladium on charcoal. The hydrogen produced in this process may be used in the conversion of cyclohexanone to cyclohexanol. It also may be used in the conversion of benzene to cyclohexane in processes where benzene is used as the precursor of the cyclohexane. 

---