Oxidation nylon

In dry heat sterilization, the temperature varies between 160 and 190°C. This is above the melting and softening temperatures of many linear polymers like polyethylene and PMMA. In the case of polyamide (Nylon), oxidation will occur at the dry sterilization temperature although this is below its melting temperature. The only polymers which can safely be dry sterflized are PTFE and silicone rubber. 

Corona or electrical Polyolefins, nylon. Oxidation and introduction... 

Colourless liquid with a strong peppermintlike odour b.p. 155" C. Manufactured by passing cyclohexanol vapour over a heated copper catalyst. Volatile in steam. Oxidized to adipic acid. Used in the manufacture of caprolactam. Nylon, adipic acid, nitrocellulose lacquers, celluloid, artificial leather and printing inks. 

C, b.p. 16UC. Manufactured by heating phenol with hydrogen under pressure in the presence of suitable catalysts. Oxidized to adipic acid (main use as intermediate for nylon production) dehydrogenated to cyclohexanone. 

Since adipic acid has been produced in commercial quantities for almost 50 years, it is not surprising that many variations and improvements have been made to the basic cyclohexane process. In general, however, the commercially important processes stiU employ two major reaction stages. The first reaction stage is the production of the intermediates cyclohexanone [108-94-1] and cyclohexanol [108-93-0], usuaHy abbreviated as KA, KA oil, ol-one, or anone-anol. The KA (ketone, alcohol), after separation from unreacted cyclohexane (which is recycled) and reaction by-products, is then converted to adipic acid by oxidation with nitric acid. An important alternative to this use of KA is its use as an intermediate in the manufacture of caprolactam, the monomer for production of nylon-6 [25038-54-4]. The latter use of KA predominates by a substantial margin on a worldwide basis, but not in the United States. 

Decabromododiphenyl Oxide—Polyacrylate Finish. This finish, effective on both polyester and nylon fabrics, is one of the most effective finishes available (ca 1993) for cotton—polyester blends (131). Relatively high cost and difficulty in appUcation may have prevented more widespread use. 

Cyclohexane. The LPO of cyclohexane [110-82-7] suppUes much of the raw materials needed for nylon-6 and nylon-6,6 production. Cyclohexanol (A) and cyclohexanone (K) maybe produced selectively by using alow conversion process with multiple stages (228—232). The reasons for low conversion and multiple stages (an approach to plug-flow operation) are apparent from Eigure 2. Several catalysts have been reported. The selectivity to A as well as the overall process efficiency can be improved by using boric acid (2,232,233). K/A mixtures are usually oxidized by nitric acid in a second step to adipic acid (233) (see Cyclohexanol and cyclohexanone). 

Dilute nitric acid can be used to oxidize an aliphatic hydrocarbon. For example, a significant use for nitric acid is the oxidation of cyclohexanol and cyclohexanone (qv) to produce adipic acid (qv). Most adipic acid is used for the production of nylon-6,6. 

Adipic acid (qv) has a wide variety of commercial uses besides the manufacture of nylon-6,6, and thus is a common industrial chemical. Many routes to its manufacture have been developed over the years but most processes in commercial use proceed through a two-step oxidation of cyclohexane [110-83-8] or one of its derivatives. In the first step, cyclohexane is oxidized with air at elevated temperatures usually in the presence of a suitable catalyst to produce a mixture of cyclohexanone [108-94-1] and cyclohexanol [108-93-0] commonly abbreviated KA (ketone—alcohol) or KA oil ... 

The diacids for these polymers are prepared via different processes. A2elaic acid [123-99-9] for nylon-6,9 [28757-63-3] is generally produced from naturally occurring fatty acids via oxidative cleavage of a double bond in the 9-position, eg, from oleic acid [112-80-1] ... 

The by-product of this process, pelargonic acid [112-05-0] is also an item of commerce. The usual source of sebacic acid [111-20-6] for nylon-6,10 [9008-66-6] is also from a natural product, ticinoleic acid [141-22-0] (12-hydroxyoleic acid), isolated from castor oil [8001-79-4]. The acid reacts with excess sodium or potassium hydroxide at high temperatures (250—275°C) to produce sebacic acid and 2-octanol [123-96-6] (166) by cleavage at the 9,10-unsaturated position. The manufacture of dodecanedioic acid [693-23-2] for nylon-6,12 begins with the catalytic trimerization of butadiene to make cyclododecatriene [4904-61-4] followed by reduction to cyclododecane [294-62-2] (see Butadiene). The cyclododecane is oxidatively cleaved to dodecanedioic acid in a process similar to that used in adipic acid production. 

Nylon-13,13 and Nylon-13. The ingredients for nylon-13,13 [26796-68-9] [26796-70-3] and nylon-13 [14465-66-8], [26916-48-3] and their copolymers have become available in developmental quantities from a natural source, crambe and rapeseed oil (176). Emcic acid [112-86-7] is obtained in high yield approaching 50 wt % from the oil and oxidatively cleaved to produce the dicarboxyhc acid, brassyUc acid [505-55-2] and pelargonic acid ... 

Antioxidants (qv) are used to prevent thermal and oxidative degradation of nylon in manufacturing, post-fiber and fabric processing, and final use. 

Oxidation. AH polyamides are susceptible to oxidation. This involves the initial formation of a free radical on the carbon alpha to the NH group, which reacts to form a peroxy radical with subsequent chain reactions leading to chain scission and yellowing. As soon as molten nylon is exposed to air it starts to discolor and continues to oxidize until it is cooled to below 60°C. It is important, therefore, to minimize the exposure of hot nylon to air to avoid discoloration or loss of molecular weight. Similarly, nylon parts exposed to high temperature in air lose their properties with time as a result of oxidation. This process can be minimized by using material containing stabilizer additives. 

Rotomolding. Nylon-6, nylon-11, and nylon-12 can be used in rotomolding and are generally suppHed for these appHcations as a powder or with a small pellet si2e. The process involves tumbling the resin in a heated mold to form large, thin-walled mol dings. Nylon-11 and nylon-12 use mold temperatures of 230—280°C and nylon-6 is processed at over 300°C. An inert gas atmosphere is preferred to avoid oxidation. 

Flame Retardants. Flame retardants are added to nylon to eliminate burning drips and to obtain short self-extinguishing times. Halogenated organics, together with catalysts such as antimony trioxide, are commonly used to give free-radical suppression in the vapor phase, thus inhibiting the combustion process. Some common additives are decabromodiphenyl oxide, brominated polystyrene, and chlorinated... 

Polymer Blends. Commercial blends of nylon with other polymers have also been produced in order to obtain a balance of the properties of the two materials or to reduce moisture uptake. Blends of nylon-6,6 with poly(phenylene oxide) have been most successflil, but blends of nylon-6,6 and nylon-6 with polypropylene have also been introduced. 

Polymer Blends. The miscibility of poly(ethylene oxide) with a number of other polymers has been studied, eg, with poly (methyl methacrylate) (18—23), poly(vinyl acetate) (24—27), polyvinylpyrroHdinone (28), nylon (29), poly(vinyl alcohol) (30), phenoxy resins (31), cellulose (32), cellulose ethers (33), poly(vinyl chloride) (34), poly(lactic acid) (35), poly(hydroxybutyrate) (36), poly(acryhc acid) (37), polypropylene (38), and polyethylene (39). 

Ammonia is used in the fibers and plastic industry as the source of nitrogen for the production of caprolactam, the monomer for nylon 6. Oxidation of propylene with ammonia gives acrylonitrile (qv), used for the manufacture of acryHc fibers, resins, and elastomers. Hexamethylenetetramine (HMTA), produced from ammonia and formaldehyde, is used in the manufacture of phenoHc thermosetting resins (see Phenolic resins). Toluene 2,4-cHisocyanate (TDI), employed in the production of polyurethane foam, indirectly consumes ammonia because nitric acid is a raw material in the TDI manufacturing process (see Amines Isocyanates). Urea, which is produced from ammonia, is used in the manufacture of urea—formaldehyde synthetic resins (see Amino resins). Melamine is produced by polymerization of dicyanodiamine and high pressure, high temperature pyrolysis of urea, both in the presence of ammonia (see Cyanamides). 

Other Reinforcement Ma.teria.Is. Other materials that have been used in tire compounds for reinforcement are chopped wire (brass-coated), cotton and nylon flock, chopped nylon strands, polyethylene, zinc oxide, and chopped Kevlar. Most of these materials have very limited apphcation and some are obsolete. Others are used more extensively in soHd mbber industrial tires than in pneumatics. 

Benzoic Acid. Ben2oic acid is manufactured from toluene by oxidation in the liquid phase using air and a cobalt catalyst. Typical conditions are 308—790 kPa (30—100 psi) and 130—160°C. The cmde product is purified by distillation, crystallization, or both. Yields are generally >90 mol%, and product purity is generally >99%. Kalama Chemical Company, the largest producer, converts about half of its production to phenol, but most producers consider the most economic process for phenol to be peroxidation of cumene. Other uses of benzoic acid are for the manufacture of benzoyl chloride, of plasticizers such as butyl benzoate, and of sodium benzoate for use in preservatives. In Italy, Snia Viscosa uses benzoic acid as raw material for the production of caprolactam, and subsequendy nylon-6, by the sequence shown below. 

The positive plates are siatered silver on a silver grid and the negative plates are fabricated from a mixture of cadmium oxide powder, silver powder, and a binder pressed onto a silver grid. The main separator is four or five layers of cellophane with one or two layers of woven nylon on the positive plate. The electrolyte is aqeous KOH, 50 wt %. In the aerospace appHcations, the plastic cases were encapsulated in epoxy resins. Most usehil cell sizes have ranged from 3 to 15 A-h, but small (0.1 A-h) and large (300 A-h) sizes have been evaluated. Energy densities of sealed batteries are 26-31 W-h/kg. 

Benzene is alkylated with propylene to yield cumene (qv). Cumene is catalytically oxidized in the presence of air to cumene hydroperoxide, which is decomposed into phenol and acetone (qv). Phenol is used to manufacture caprolactam (nylon) and phenoHc resins such as bisphenol A. Approximately 22% of benzene produced in 1988 was used to manufacture cumene. 

Benzene is hydrogenated to cyclohexane. Cyclohexane is then oxidized to cyclohexanol, cyclohexanone, or adipic acid (qv). Adipic acid is used to produce nylon. Cyclohexane manufacture was responsible for about 14% of benzene consumption in 1988. 

Hydrocarbon Oxidation. The oxidation of hydrocarbons (qv) and hydrocarbon derivatives can be significantly altered by boron compounds. Several large-scale commercial processes, such as the oxidation of cyclohexane to a cyclohexanol—cyclohexanone mixture in nylon manufacture, are based on boron compounds (see Cylcohexanoland cyclohexanone Eibers, polyamide). A number of patents have been issued on the use of borate esters and boroxines in hydrocarbon oxidation reactions, but commercial processes apparently use boric acid as the preferred boron source. The Hterature in this field has been covered through 1967 (47). Since that time the Hterature consists of foreign patents, but no significant appHcations have been reported for borate esters. 

Caprolactam [105-60-2] (2-oxohexamethyleiiiiriiQe, liexaliydro-2J -a2epin-2-one) is one of the most widely used chemical intermediates. However, almost all of the aimual production of 3.0 x 10 t is consumed as the monomer for nylon-6 fibers and plastics (see Fibers survey Polyamides, plastics). Cyclohexanone, which is the most common organic precursor of caprolactam, is made from benzene by either phenol hydrogenation or cyclohexane oxidation (see Cyclohexanoland cyclohexanone). Reaction with ammonia-derived hydroxjlamine forms cyclohexanone oxime, which undergoes molecular rearrangement to the seven-membered ring S-caprolactam. 

---