Liquid coating

Liquid coating resins are prepared by reacting methanol or butanol with the initial hydroxyme-thylureas. Ether exchange reactions between the amino resin and the reactive sites on the polymer produce a cross-linked film. 

A chromatographic technique in which the mobile phase is a gas and the stationary phase is a liquid coated either on a solid packing material or on the column s walls. 

Roll and coil coating systems utilize liquid coating materials with organic solvents, which must be stored, manifested, and disposed of according to 40 CFR Part 262 if classified as hazardous waste under 40 CFR Part 261. 

Liquid coating materials with low organic solvent content should be used to minimize the amount of volatile organic compounds that will be volatized and to reduce the volume of solid and liquid hazardous waste created. 

In the lower region of the unsaturated zone, immediately above the water table, is the capillary fringe, where water is drawn upward by capillary attraction. Above the capillary fringe, moisture coats the solid surfaces of the soil or rock particles. If the liquid coating becomes too thick to be held by surface tension, a droplet will pull away and be drawn downward by gravity. The fluid can also evaporate and move through the air space in the pores as water vapor. 

Crosslinked acrylic microgels in aqueous and non-aqueous media were patented as paint constituents in 1979 to improve the orientation of aluminum flake pigments, restrict the flow of the liquid coating on the substrate and restrict sagging [324]. As the patent speaks of emulsions, insolubility of the microgels and particle sizes up to 200 nm, it is questionable whether these polymers consisted of microgels only. 

Hexamethylolmelamine can further condense in the presence of an acid catalyst ether linkages can also form (see Urea Formaldehyde ). A wide variety of resins can be obtained by careful selection of pH, reaction temperature, reactant ratio, amino monomer, and extent of condensation. Liquid coating resins are prepared by reacting methanol or butanol with the initial methylolated products. These can be used to produce hard, solvent-resistant coatings by heating with a variety of hydroxy, carboxyl, and amide functional polymers to produce a cross-linked film. 

In a partition system the stationary phase is a liquid coated onto a solid support (p. 97). Silica gel, kieselguhr (diatomaceous earth) or cellulose powder are the most frequently used. Conditions closely resemble those of counter-current distribution so that in the absence of adsorption by the solid support, solutes move through the system at rates determined by their... 

Gas chromatography makes use, as the stationary phase, a glass or metal column fdled either with a powdered adsorbent or a non-volatile liquid coated on a non-adsorbent powder. The mobile-phase consists of an inert-gas loaded with the vapourised mixture of solutes flowing through the stationary phase at a suitable temperature. In the course of the passage of the vapour of the sample through the column, separation of the components of the sample occurs in two ways, namely ... 

Qin, W, and Li, S. F. Y. (2002). An ionic liquid coating for determination of sildenafil and UK-103,320 in human serum by capillary zone electrophoresis-ion trap mass spectrometry. Electrophoresis 23, 4110—4116. 

Abstract The principle of catalytic SILP materials involves surface modification of a porous solid material by an ionic liquid coating. Ionic liquids are salts with melting points below 100 °C, generally characterized by extremely low volatilities. In the examples described in this paper, the ionic liquid coating contains a homogeneously dissolved Rh-complex and constitutes a uniform, thin film, which itself displays the catalytic reactivity in the system. Continuous fixed-bed reactor technology has been applied successfully to demonstrate the feasibility of catalytic SILP materials for propene hydroformylation and methanol carbonylation. 

Wallach transformation orgchem By the use of concentrated sulfuric acid, an azoxy-benzene is converted into a pura-hydroxyazobenzene. wal ak. tranz-far.ma-shan wall-coated capillary column analychem Acaplllary column characterized bya layer of stationary liquid coated directly on the Inner wall of a colled capillary tube. wol kod-3d kap-3 ler-e. kal am )... 

An integrally monlded composite article comprised of (I) a nonfoam layer formed from a thermoplastic elastomer powder composition (A) and (II) a foam layer formed from a foamable composition comprised of (i) (B) a thermoplastic synthetic resin powder, and (C) a heat decomposable foaming agent and (D) a liquid coating agent, wherein the thermoplastic elastomer powder (A) is comprised of a composition of an ethylene-alpha-olefm copolymer mbber and a polyolefin resin or thermoplastic elastomer powder comprised of a partially crosslinked composition of an ethylene-alpha-olefm copolymer mbber and a polyolefin resin, the thermoplastic elastomer powder having a complex dynamic viscosity at 250 deg C and a freqnency of 1 radian/sec of not more than 1.5x1,000,000 poise and having a Newtonian viscosity index n, calculated by a specific formula. 

Kim and Lee disclosed an ionic liquid-coated enzyme that remarkably improves enzyme functions, such as enantioselectivity and stability, when the enzyme, which may be lipase, is coated with an ionic liquid. Further, even in the case where the ionic liquid-coated enzyme is reused, the... 

A less expensive replacement for zinc chromate is obtained by combining the zinc salt of 5-nitroisophthalic acid with zinc phosphate pigments (Section 5.2.2.5) [5.65], [5.67], [5.181]. A concentration of 0.5-2.0% based on the liquid coating is recommended. 

Collection Efficiency. Single-Tube Denuders. For the appropriate design of a diffusion-based collection device for an intended application, the ability to estimate the collection efficiency a priori is of considerable help. Although the theoretical soundness of the Gormley-Kennedy equation (equation 1) is not questioned, it is based on the assumption that the uptake probability of the analyte gas at the wall is unity that is, the wall is truly a perfect sink , and every collision results in uptake. This assumption is unrealistic. In recent years, this issue has been reexamined. McMurry and Stolzenburg (42) showed for a liquid-coated denuder how the uptake probability (discussed by the authors in terms of the mass accommodation coefficient ) can be evaluated from collection efficiency measurements. Murphy and Fahey (43) utilized the mathematical solution originally developed for hemodialyzers by Cooney et al. (44) this treatment assumes a constant uptake probability that may be less than unity. To use the Murphy-Fahey approach, however, this probability must be precisely known. 

The last term accounts for the resistance to mass transfer in the gas phase. Low-loaded liquid coatings cause the Cg term to be significant. Equation 2.82 was further extended to account for velocity distributions due to retarded gas flow in the layers (C ) and the interaction of the two types of gas resistance (C2) ... 

Increased column diameter may cause a reduction in the homogeneity of the packing, resulting in flowrate distortion of the component zones across the column cross-section and higher h (HETP) values. Diminution of column efficiency also can be related to (1) the nonuniformity of liquid coating which in turn affects mass transfer, (2) the radial temperature gradient that... 

---