Latex emulsion polymerization particle

Computerized HDC for Monitoring the Latex Emulsion Polymerization Particle Growth Patterns. 

The polymerization process is performed by using one of the following three methods emulsion polymerization, suspension polymerization or bulk polymerization. The first and oldest method is rarely used (around 10% of PVC is produced this way). The production can be periodic or continuous. In the continuous method, there is a negative effect of the polymer being deposited in autoclaves, which can lead to deterioration in heat exchange and an increase in the amoimt of coagulum (non-coUoidal particles of latex). Emulsion polymerization is conducted in the presence of initiators dissolved in water, i.e., non-organic oxides (ammonium, potasium persulfate), emulsifiers (mostly anionic alkylbenzyl sulfonate, fatty acids salts, alkylphenyl ethoxides and fatty acids). The selection and the amount of the emulsifier is crucial since it affects the properties of latex, the particle size, the stability, and the tendency of the powder to cake. Other aids used in the process of polymerization are buffers phosphates and sodium carbonate. 

Emulsion polymerization also has the advantages of good heat transfer and low viscosity, which follow from the presence of the aqueous phase. The resulting aqueous dispersion of polymer is called a latex. The polymer can be subsequently separated from the aqueous portion of the latex or the latter can be used directly in eventual appUcations. For example, in coatings applications-such as paints, paper coatings, floor pohshes-soft polymer particles coalesce into a continuous film with the evaporation of water after the latex has been applied to the substrate. 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

The product of an emulsion polymerization is a latex ie, polymer particles on the order of 0.5—0.15 p.m stabilized by the soap. These form the basis for the popular latex paints. SoHd mbber is recovered by coagulating the latex with ionic salts and acids (see Latex technology). 

Soap. A critical ingredient for emulsion polymerization is the soap (qv), which performs a number of key roles, including production of oil (monomer) in water emulsion, provision of the loci for polymerization (micelle), stabilization of the latex particle, and impartation of characteristics to the finished polymer. 

A typical recipe for batch emulsion polymerization is shown in Table 13. A reaction time of 7—8 h at 30°C is requited for 95—98% conversion. A latex is produced with an average particle diameter of 100—150 nm. Other modifying ingredients may be present, eg, other colloidal protective agents such as gelatin or carboxymethylcellulose, initiator activators such as redox types, chelates, plasticizers, stabilizers, and chain-transfer agents. 

The kinetics of vinyl acetate emulsion polymeriza tion in the presence of alkyl phenyl ethoxylate surfactants of various chain lengths indicate that part of the emulsion polymerization occurs in the aqueous phase and part in the particles (115). A study of the emulsion polymerization of vinyl acetate in the presence of sodium lauryl sulfate reveals that a water-soluble poly(vinyl acetate)—sodium dodecyl sulfate polyelectrolyte complex forms, and that latex stabihty, polymer hydrolysis, and molecular weight are controlled by this phenomenon (116). 

Partially hydrolyzed poly(vinyl alcohol) grades are preferred because they have a hydrophobic /hydrophilic balance that make them uniquely suited for emulsion polymerization. The compatibUity of the residual acetate units with the poly(vinyl acetate) latex particles partly explains the observed stabilization effect. The amount of PVA employed is normally 4—10% on the weight of vinyl acetate monomer. The viscosity of the resulting latex increases with increasing molecular weight and decreasing hydrolysis of the PVA (318). 

Emulsions Emulsions have particles of 0.05 to 5.0 [Lm diameter. The product is a stable latex, rather than a filterable suspension. Some latexes are usable directly, as in paints, or they may be coagulated by various means to produce massive polymers. Figures 23-23d and 23-23 show bead and emulsion processes for vinyl chloride. Continuous emulsion polymerization of outadiene-styrene rubber is done in a CSTR battery with a residence time of 8 to 12 h. Batch treating of emulsions also is widely used. 

A new process, from Norway, has filled the size gap between emulsion and suspension polymerization techniques [7,8]. This novel polymerization method, the so-called swollen emulsion polymerization has been developed by Ugelstad for producing uniform polymeric particles in the size range of 2-100 /nm. This process comprises successive swelling steps and repolymerizations for increasing the particle size of seed polymer particles by keeping the monodispersity of the seed latex. 

The progression of an ideal emulsion polymerization is considered in three different intervals after forming primary radicals and low-molecular weight oligomers within the water phase. In the first stage (Interval I), the polymerization progresses within the micelle structure. The oligomeric radicals react with the individual monomer molecules within the micelles to form short polymer chains with an ion radical on one end. This leads to the formation of a new phase (i.e., polymer latex particles swollen with the monomer) in the polymerization medium. 

An emulsion polymerization reaction follows three conventional steps, namely, initiation, propagation, and termination. These steps can be described by the conventional reactions that are valid for any free radical polymerization. Smith and Ewart [10] proposed that a forming latex particle in an ideal emulsion polymeriza-... 

The rate of an ideal emulsion polymerization is given by Eqn (4). In this expression [/] is the initiator concentration, [ ] is the emulsifier concentration, and [M] is the concentration of monomer within the forming latex particles. This value is constant for a long reaction period until all the monomer droplets disappear within the water phase. 

The monomer concentration within the forming latex particles does not change for a long period due to the diffusion of monomer from the droplets to the polymerization loci. Therefore, the rate of the propagation reaction does not change and a constant polymerization rate period is observed in a typical emulsion polymerization system. 

Figure 5 The schematical view of the latex particles obtained as the product of emulsion polymerization.

The function of emulsifier in the emulsion polymerization process may be summarized as follows [45] (1) the insolubilized part of the monomer is dispersed and stabilized within the water phase in the form of fine droplets, (2) a part of monomer is taken into the micel structure by solubilization, (3) the forming latex particles are protected from the coagulation by the adsorption of monomer onto the surface of the particles, (4) the emulsifier makes it easier the solubilize the oligomeric chains within the micelles, (5) the emulsifier catalyzes the initiation reaction, and (6) it may act as a transfer agent or retarder leading to chemical binding of emulsifier molecules to the polymer. 

Based on the Smith-Ewart theory, the number of latex particles formed and the rate of polymerization in Interval II is proportional with the 0,6 power of the emulsifier concentration. This relation was also observed experimentally for the emulsion polymerization of styrene by Bartholomeet al. [51], Dunn and Al-Shahib [52] demonstrated that when the concentrations of the different emulsifiers were selected so that the micellar concentrations were equal, the same number of particles having the same size could be obtained by the same polymerization rates in Interval II in the existence of different emulsifiers [52], The number of micelles formed initially in the polymerization medium increases with the increasing emulsifier concentration. This leads to an increase in the total amount of monomer solubilized by micelles. However, the number of emulsifier molecules in one micelle is constant for a certain type of emulsifier and does not change with the emulsifier concentration. The monomer is distributed into more micelles and thus, the... 

Medvedev et al. [57] extensively studied the use of nonionic emulsifiers in emulsion polymerization. The emulsion polymerizations in the presence of nonionic emulsifiers exhibited some differences relative to those carried out with the ionic ones. Medvedev et al, [57] proposed that the size of latex particles remained constant during the reaction period, but their number increased continually with the increasing monomer conversion. The use of nonionic emulsifiers in emulsion polymerization usually results in larger sizes relative to those obtained by the ionic emulsifiers. It is possible to reach a final size value of 250 nm by the use of nonionic emulsifiers in the emulsion polymerization of styrene [58]. 

Multistage emulsion polymerization techniques are usually applied for (1) the synthesis of large uniform latex particles, (2) the introduction of functional groups into the uniform latex particles, or (3) the synthesis of macroporous uniform latex particles. 

Multistage emulsion polymerization has been proposed by Ugelstad et al. [108,109] for the synthesis of large uniform latex particles. In general, the multistage emulsion polymerization techniques include two main... 

Sheu and coworkers [111] produced polysty-rene-polydivinylbenzene latex interpenetrating polymer networks by the seeded emulsion polymerization of styrene-divinylbenzene in the crosslinked uniform polystyrene particles. In this study, a series of uniform polystyrene latexes with different sizes between 0.6 and 8.1... 

New methods of emulsion polymerization, particularly the use of swelhng agents, are needed to produce monodisperse latexes with a desired size and surface chemistiy. Samples of latex spheres with uniform diameters up to 100 pm are now commercially available. These spheres and other mono-sized particles of various shapes can be used as model colloids to study two- and three-dimensional many-body systems of very high complexity. 

This paper presents the physical mechanism and the structure of a comprehensive dynamic Emulsion Polymerization Model (EPM). EPM combines the theory of coagulative nucleation of homogeneously nucleated precursors with detailed species material and energy balances to calculate the time evolution of the concentration, size, and colloidal characteristics of latex particles, the monomer conversions, the copolymer composition, and molecular weight in an emulsion system. The capabilities of EPM are demonstrated by comparisons of its predictions with experimental data from the literature covering styrene and styrene/methyl methacrylate polymerizations. EPM can successfully simulate continuous and batch reactors over a wide range of initiator and added surfactant concentrations. 

---