Emulsion polymerization particles

Even though the chemical reactions are the same (i.e. combination, disproportionation), the effects of compartmentalization are such that, in emulsion polymerization, particle phase termination rates can be substantially different to those observed in corresponding solution or bulk polymerizations. A critical parameter is n, the average number of propagating species per particle. The value of h depends on the particle size and the rates of entry and exit. 

Computerized HDC for Monitoring the Latex Emulsion Polymerization Particle Growth Patterns. 

As in the case of emulsion polymerization, particle morphology is ruled by the interplay between thermodynamics and kinetics. Equilibrium morphologies are reached when the internal viscosity of the polymer particle is low. Thus, due to the plasticizing effect of the alkyd resin, equilibrium morphologies are usually reached for alkyd/acrylic systems [96]. The equilibrium morphology is affected by the presence of graft copolymer that reduces the interfacial tension between the polymer phases in the particle. Methods to calculate the equilibrium morphology of multiphase polymer particles are available [43]. 

The production of organic polymeric particles in tire size range of 30-300 nm by emulsion polymerization has become an important teclmological application of surfactants and micelles. Emulsion polymerization is very well and extensively reviewed in many monographs and texts [67, 68], but we want to briefly illustrated tire role of micelles in tliis important process. 

Figure C2.3.11 Key surfactant stmctures (not to scale) in emulsion polymerization micelles containing monomer and oligomer, growing polymer particle stabilized by surfactant and an emulsion droplet of monomer (reservoir) also coated with surfactant. Adapted from figure 4-1 in [67],...

Figure 6.10 Schematic representation of the distribution of surfactant in an emulsion polymerization. Note the relative sizes of suspended particles. [From J. W. Vanderhoff, E. B. Bradford, H. L. Tarkowski, J. B. Shaffer, and R. M. Wiley,Chem. 34 32(1962).]...

Emulsion polymerization also has the advantages of good heat transfer and low viscosity, which follow from the presence of the aqueous phase. The resulting aqueous dispersion of polymer is called a latex. The polymer can be subsequently separated from the aqueous portion of the latex or the latter can be used directly in eventual appUcations. For example, in coatings applications-such as paints, paper coatings, floor pohshes-soft polymer particles coalesce into a continuous film with the evaporation of water after the latex has been applied to the substrate. 

Microemulsion Polymerization. Polyacrylamide microemulsions are low viscosity, non settling, clear, thermodynamically stable water-in-od emulsions with particle sizes less than about 100 nm (98—100). They were developed to try to overcome the inherent settling problems of the larger particle size, conventional inverse emulsion polyacrylamides. To achieve the smaller microemulsion particle size, increased surfactant levels are required, making this system more expensive than inverse emulsions. Acrylamide microemulsions form spontaneously when the correct combinations and types of oils, surfactants, and aqueous monomer solutions are combined. Consequendy, no homogenization is required. Polymerization of acrylamide microemulsions is conducted similarly to conventional acrylamide inverse emulsions. To date, polyacrylamide microemulsions have not been commercialized, although work has continued in an effort to exploit the unique features of this technology (100). 

Emulsion Process. The emulsion polymerization process utilizes water as a continuous phase with the reactants suspended as microscopic particles. This low viscosity system allows facile mixing and heat transfer for control purposes. An emulsifier is generally employed to stabilize the water insoluble monomers and other reactants, and to prevent reactor fouling. With SAN the system is composed of water, monomers, chain-transfer agents for molecular weight control, emulsifiers, and initiators. Both batch and semibatch processes are employed. Copolymerization is normally carried out at 60 to 100°C to conversions of - 97%. Lower temperature polymerization can be achieved with redox-initiator systems (51). 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

There are two principal PVC resins for producing vinyl foams suspension resin and dispersion resin. The suspension resin is prepared by suspension polymerization with a relatively large particle size in the 30—250 p.m range and the dispersion resin is prepared by emulsion polymerization with a fine particle size in the 0.2—2 p.m range (245). The latter is used in the manufacture of vinyl plastisols which can be fused without the appHcation of pressure. In addition, plastisol blending resins, which are fine particle size suspension resins, can be used as a partial replacement for the dispersion resin in a plastisol system to reduce the resin costs. 

Early efforts to produce synthetic mbber coupled bulk polymerization with subsequent emulsification (9). Problems controlling the heat generated during bulk polymerization led to the first attempts at emulsion polymerization. In emulsion polymerization hydrophobic monomers are added to water, emulsified by a surfactant into small particles, and polymerized using a water-soluble initiator. The result is a coUoidal suspension of fine particles,... 

Initia.tors, The initiators most commonly used in emulsion polymerization are water soluble although partially soluble and oil-soluble initiators have also been used (57). Normally only one initiator type is used for a given polymerization. In some cases a finishing initiator is used (58). At high conversion the concentration of monomer in the aqueous phase is very low, leading to much radical—radical termination. An oil-soluble initiator makes its way more readily into the polymer particles, promoting conversion of monomer to polymer more effectively. 

Emulsion Polymerization. When the U.S. supply of natural mbber from the Far East was cut off in World War II, the emulsion polymerization process was developed to produce synthetic mbber. In this complex process, the organic monomer is emulsified with soap in an aqueous continuous phase. Because of the much smaller (<0.1 jira) dispersed particles than in suspension polymerization and the stabilizing action of the soap, a proper emulsion is stable, so agitation is not as critical. In classical emulsion polymerization, a water-soluble initiator is used. This, together with the small particle size, gives rise to very different kinetics (6,21—23). 

The product of an emulsion polymerization is a latex ie, polymer particles on the order of 0.5—0.15 p.m stabilized by the soap. These form the basis for the popular latex paints. SoHd mbber is recovered by coagulating the latex with ionic salts and acids (see Latex technology). 

Soap. A critical ingredient for emulsion polymerization is the soap (qv), which performs a number of key roles, including production of oil (monomer) in water emulsion, provision of the loci for polymerization (micelle), stabilization of the latex particle, and impartation of characteristics to the finished polymer. 

Copolymers with butadiene, ie, those containing at least 60 wt % butadiene, are an important family of mbbers. In addition to synthetic mbber, these compositions have extensive uses as paper coatings, water-based paints, and carpet backing. Because of unfavorable reaction kinetics in a mass system, these copolymers are made in an emulsion polymerization system, which favors chain propagation but not termination (199). The result is economically acceptable rates with desirable chain lengths. Usually such processes are mn batchwise in order to achieve satisfactory particle size distribution. 

Emulsion Polymerization. Emulsion and suspension reactions are doubly heterogeneous the polymer is insoluble in the monomer and both are insoluble in water. Suspension reactions are similar in behavior to slurry reactors. Oil-soluble initiators are used, so the monomer—polymer droplet is like a small mass reaction. Emulsion polymerizations are more complex. Because the monomer is insoluble in the polymer particle, the simple Smith-Ewart theory does not apply (34). 

A kinetic model for the particle growth stage for continuous-addition emulsion polymerization has been proposed (35). Below the monomer... 

A typical recipe for batch emulsion polymerization is shown in Table 13. A reaction time of 7—8 h at 30°C is requited for 95—98% conversion. A latex is produced with an average particle diameter of 100—150 nm. Other modifying ingredients may be present, eg, other colloidal protective agents such as gelatin or carboxymethylcellulose, initiator activators such as redox types, chelates, plasticizers, stabilizers, and chain-transfer agents. 

Many different combinations of surfactant and protective coUoid are used in emulsion polymerizations of vinyl acetate as stabilizers. The properties of the emulsion and the polymeric film depend to a large extent on the identity and quantity of the stabilizers. The choice of stabilizer affects the mean and distribution of particle size which affects the rheology and film formation. The stabilizer system also impacts the stabiUty of the emulsion to mechanical shear, temperature change, and compounding. Characteristics of the coalesced resin affected by the stabilizer include tack, smoothness, opacity, water resistance, and film strength (41,42). 

The kinetics of vinyl acetate emulsion polymeriza tion in the presence of alkyl phenyl ethoxylate surfactants of various chain lengths indicate that part of the emulsion polymerization occurs in the aqueous phase and part in the particles (115). A study of the emulsion polymerization of vinyl acetate in the presence of sodium lauryl sulfate reveals that a water-soluble poly(vinyl acetate)—sodium dodecyl sulfate polyelectrolyte complex forms, and that latex stabihty, polymer hydrolysis, and molecular weight are controlled by this phenomenon (116). 

---