Ionically Conducting Molten Salts

Molten Carbonate Fuel Cell. The electrolyte ia the MCFC is usually a combiaation of alkah (Li, Na, K) carbonates retaiaed ia a ceramic matrix of LiA102 particles. The fuel cell operates at 600 to 700°C where the alkah carbonates form a highly conductive molten salt and carbonate ions provide ionic conduction. At the operating temperatures ia MCFCs, Ni-based materials containing chromium (anode) and nickel oxide (cathode) can function as electrode materials, and noble metals are not required. 

Recently, room-temperature ionic liquids (molten salts) have been extensively studied in order to replace volatile organic solvents by them in electrochemical devices such as batteries. Interest in these materials is stimulated by their properties (e.g., high ionic conductivity, good electrochemical stability, and low volatility). Among these properties, the low volatility is the most critical for ensuring the long-term stability of electrochemical devices. Room-temperature ionic liq-... 

The electrolyte in this fuel cell is generally a combination of alkali carbonates, which are retained in a ceramic matrix of LiA102 [8], This fuel cell type works at 600°C-700°C, where the alkali carbonates form a highly conductive molten salt with carbonate ions providing ionic conduction. At the high operating temperatures in the molten carbonate fuel cell, a metallic nickel anode and a nickel oxide cathode are adequate to promote the reaction [9], Noble metals are not required. 

The use of solvent-free electrolytes, i.e., high temperature ionic liquids (molten salt) electrolytes, which only become ionically conductive upon melting when heated to high temperatures. Another variant is the use of low rate, room temperature solid electrolytes. 

The Mechanism of Ionic Conduction, Molten sodium chloride, like the crystalline substance, consists of equal numbers of sodium ions and chloride ions. These ions are very stable, and do not gain electrons or lose electrons easily. Whe -eas the ions in the crystal are firmly held in place by their neighbors, those in the molten salt move about with considerable freedom. 

The FC operates in the temperature range 855-960 K, where the alkali metal carbonates form a highly conductive molten salt, with carbonate ions providing ionic conduction. A lower temperature causes problems with electrolyte solidification, and higher temperatures have drawbacks for the materials and corrosion. At the high operating temperatures employed, noble metal catalysts are not required in fact, nickel (anode) and nickel oxide (cathode), that is, low-cost materials, are adequate to promote the reaction. 

Electrochemical reactions involve the transfer of electrons between an electronically conducting phase and localised energy levels on molecules or ions in an adjacent phase. In many cases, the reacting chemical species are present in an electrolyte solution, but interfacial charge transfer reactions can also involve solid ionic or covalent phases as well as ionic liquids (molten salts). Since the description of electron transfer should be applicable to a wide range of systems, it is useful to list some of the materials which can form part of the interface... 

Molten carbonate fuel cells (MCFC) have the electrolyte composed of a combination of alkali (Li, Na, K) carbonates. Operating temperatures are between 600 and 700°C where the carbonates form a highly conductive molten salt, with carbonate ions providing ionic conduction. These fuel cells are in the precommercial / demonstration stage for stationary power generation [1]. 

The most direct effect of defects on tire properties of a material usually derive from altered ionic conductivity and diffusion properties. So-called superionic conductors materials which have an ionic conductivity comparable to that of molten salts. This h conductivity is due to the presence of defects, which can be introduced thermally or the presence of impurities. Diffusion affects important processes such as corrosion z catalysis. The specific heat capacity is also affected near the melting temperature the h capacity of a defective material is higher than for the equivalent ideal crystal. This refle the fact that the creation of defects is enthalpically unfavourable but is more than comp sated for by the increase in entropy, so leading to an overall decrease in the free energy... 

Early in their work on molten salt electrolytes for thermal batteries, the Air Force Academy researchers surveyed the aluminium electroplating literature for electrolyte baths that might be suitable for a battery with an aluminium metal anode and chlorine cathode. They found a 1948 patent describing ionically conductive mixtures of AICI3 and 1-ethylpyridinium halides, mainly bromides [6]. Subsequently, the salt 1-butylpyridinium chloride/AlCl3 (another complicated pseudo-binary)... 

Electrochemically, the system metal/molten salt is somewhat similar to the system metal/aqueous solution, although there are important differences, arising largely from differences in temperature and in electrical conductivity. Most fused salts are predominantly ionic, but contain a proportion of molecular constituents, while pure water is predominantly molecular, containing very low activities of hydrogen and hydroxyl ions. Since the aqueous system has been extensively studied, it may be instructive to point out some analogues in fused-salt systems. 

Electrolyte a substance, liquid or solid, which conducts electrical current by movement of ions (not of electrons). In corrosion science, an electrolyte is usually a liquid solution of salts dissolved in a solvent, or a molten salt. The term also applies to polymers and ceramics which are ionically conductive. 

Electro-conductivity of molten salts is a kinetic property that depends on the nature of the mobile ions and ionic interactions. The interaction that leads to the formation of complex ions has a varying influence on the electroconductivity of the melts, depending on the nature of the initial components. When the initial components are purely ionic, forming of complexes leads to a decrease in conductivity, whereas associated initial compounds result in an increase in conductivity compared to the behavior of an ideal system. Since electro-conductivity is never an additive property, the calculation of the conductivity for an ideal system is performed using the well-known equation proposed by Markov and Shumina (Markov s Equation) [315]. 

When an ionic solid like sodium chloride is melted, the molten salt conducts electric current. The conductivity is like that of an aqueous salt solution Na+ and Cl- ions are present. The extremely high melting temperature (808°C) shows that a large amount of energy is needed to tfear apart the regular NaCl crystalline arrangement to free the ions so they can move. 

The classical example of a soUd organic polymer electrolyte and the first one found is the poly(ethylene oxide) (PEO)/salt system [593]. It has been studied extensively as an ionically conducting material and the PEO/hthium salt complexes are considered as reference polymer electrolytes. However, their ambient temperature ionic conductivity is poor, on the order of 10 S cm, due to the presence of crystalUne domains in the polymer which, by restricting polymer chain motions, inhibit the transport of ions. Consequently, they must be heated above about 80 °C to obtain isotropic molten polymers and a significant increase in ionic conductivity. 

The rhodium catalyzed carbonylation of ethylene and methanol can be conducted in the absence of added alkyl halide if the reactions are conducted in iodide based ionic liquids or molten salts. In the case of ethylene carbonylation, the imidazolium iodides appeared to perform best and operating in the absence of ethyl iodide gave improved selectivities relative to processes using ethyl iodide and ionic hquids. In the case of... 

The electrolyte is made by in situ chlorination of vanadium to vanadium dichloride in a molten salt bath. Higher valent chlorides are difficult to retain in the bath and thus are not preferred. The molten bath, which is formed by sodium chloride or an equimolar mixture of potassium chloride-sodium chloride or of potassium chloride-lithium chloride or of sodium chloride-calcium chloride, is contained in a graphite crucible. The crucible also serves as an anode. Electrolysis is conducted at a temperature about 50 °C above the melting point of the salt bath, using an iron or a molybdenum cathode and a cathode current density of 25 to 75 A dnT2. The overall electrochemical deposition reaction involves the formation and the discharge of the divalent ionic species, V2+ ... 

In many ways, chloroaluminate molten salts are ideal solvents for the electrodeposition of transition metal-aluminum alloys because they constitute a reservoir of reducible aluminum-containing species, they are excellent solvents for many transition metal ions, and they exhibit good intrinsic ionic conductivity. In fact, the first organic salt-based chloroaluminate melt, a mixture of aluminum chloride and 1-ethylpyridinium bromide (EtPyBr), was formulated as a solvent for electroplating aluminum [55, 56] and subsequently used as a bath to electroform aluminum waveguides [57], Since these early articles, numerous reports have been published that describe the electrodeposition of aluminum from this and related chloroaluminate systems for examples, see Liao et al. [58] and articles cited therein. 

Recently, there has been considerable interest in developing molten salts that are less air and moisture sensitive. Melts such as l-methyl-3-butylimidazolium hexa-fluorophosphate [211], l-ethyl-3-methylimidazolium trifluoromethanesulfonate [212], and l-ethyl-3-methylimidazolium tetrafluoroborate [213] are reported to be hydro-phobic and stable under environmental conditions. In some cases, metal deposition from these electrolytes has been explored [214]. They possess a wide potential window and sufficient ionic conductivity to be considered for many electrochemical applications. Of course if one wishes to take advantage of their potential air stability, one loses the opportunity to work with the alkali and reactive metals. Further, since these ionic liquids are neutral and lack the adjustable Lewis acidity common to the chloroaluminates, the solubility of transition metal salts into these electrolytes may be limited. On a positive note, these electrolytes are significantly different from the chloroaluminates in that the supporting electrolyte is not intended to be electroactive. 

Metals and semiconductors are common examples of electronic conductors, and under certain circumstances even insulators can be made electronically conducting, for example by photoexcitation. Electrolyte solutions, molten salts, and solid electrolytes are ionic conductors. Some materials have appreciable electronic and ionic conductivities,... 

Watanabe, M., Yamada, S-L, and Ogata, N., Ionic conductivity of polymer electrolytes containing room temperature molten salts based on pyridinium halide and aluminium chloride, Electrochim. Acta, 40,2285,1995. 

Nakai, Y, Ito, K., and Ohno, H., Ion conduction in molten salts prepared by terminal-charged PEO derivatives. Solid State Ionics, 113-115,199,1998. 

Ohno, H., Nakai, Y., and Ito, K., Ionic conductivity of molten salts formed by polyether/salt hybrids, Chem. Lett., 15,1998. 

Ionic liquids are a class of solvents and they are the subject of keen research interest in chemistry (Freemantle, 1998). Hydrophobic ionic liquids with low melting points (from -30°C to ambient temperature) have been synthesized and investigated, based on 1,3-dialkyl imidazolium cations and hydrophobic anions. Other imidazolium molten salts with hydrophilic anions and thus water-soluble are also of interest. NMR and elemental analysis have characterized the molten salts. Their density, melting point, viscosity, conductivity, refractive index, electrochemical window, thermal stability, and miscibility with water and organic solvents were determined. The influence of the alkyl substituents in 1,2, 3, and 4(5)-positions on the imidazolium cation on these properties has been scrutinized. Viscosities as low as 35 cP (for l-ethyl-3-methylimi-dazolium bis((trifluoromethyl)sulfonyl)amide (bis(triflyl)amide) and trifluoroacetate) and conductivities as high as 9.6 mS/cm were obtained. Photophysical probe studies were carried out to establish more precisely the solvent properties of l-ethyl-3-methyl-imidazolium bis((trifluoromethyl)sulfonyl)amide. The hydrophobic molten salts are promising solvents for electrochemical, photovoltaic, and synthetic applications (Bon-hote et al., 1996). 

Molten salts are ionic liquids and as such can be utilized in a wide range of electrochemical applications where high conductivity and ionic mobility are required (Papa-georgiou et al., 1996). Their ionic nature renders them negligibly volatile in the liquid state. These properties as well as relatively low viscosity, the large electrochemical window, thermal stability, miscibility with solvents or other salts and hydrophobicity are a few of the desirable qualities found in certain molten salts. 

Molten single salts or molten eutectic mixtures are generally characterized by very high ionic conductivities (> 100 S/m). This property makes them desirable media as battery electrolytes since it permits operation at high... 

---