Identification number, description

One method used to summarize the required devices and show the function performed by each device is with a function matrix. Figure 14-4 is a completed function matrix chart for the simple process flow diagram shown in Figure 14-5. The function matrix is from RP I4C and is called a SAFE chart. Each component is listed in the left hand column with an identification number and description. Under Device I.D., each of the devices listed in the SAC is listed. If the device is not present, the appropriate SAC reference number is listed. If the SAC rationale requires that another device be present on another component, that device is listed under Alternate Device, if applicable. 

In the following table the important process steps (Proc. no.), the process description (Process quantity) (measure), the related target data (Target data) and their tolerances (tolerances) are listed and compared with average data measured in three runs (Ave. act. data) and the minimum and maximum data measured in the three runs (min./max.). The last two data have to be taken from the protocols and to be listed. In the last column the identification number of the runs, in which the two extreme data are measured is listed (Ident. no.) The last two column are not given, with the exception of proc. nr. 1.1 as an example- The table is a proposal of how the comparison could be made. The list may not be complete in all possible cases and is concentrated on the time-, pressure- and temperature data. Other methods may be preferred to make the ability of the equipment transparent. 

Record keeping carried out not only by the analyst in laboratory notebooks, but also in logbooks for each instrument. After completion, these should be archived for at least ten years. Records should include the type of sample (with a unique identification number), collection method, location, date, description of sample, preparation and analysis method, and instrumental conditions, original data files, and the name of the person responsible. 

The manifest must contain the name, address, telephone number and EPA identification number of the generator, transporter and designated receiving facility, and description, quantity, hazardous waste ID number, and hazard class of waste. 

Is there a clear description of what source data will be recorded directly into the CRF and what will be recorded in the medical records Normally, the protocol identification number, the date of consent, the date of commencement of the study, the visit dates, the start and finish dates of the administration of study drug and/or treatment, concurrent medication, adverse events and... 

Complete identification and description of the material tested, including its physical appearance. If it is a commercial sample, include its trade-name, manufacturer, and lot number. 

The record of an experiment should begin with a brief statement of the experiment to be performed. The procedure being followed should be described in all essential detail. When the procedure is described elsewhere, the notebook entry may be abbreviated to a reference to the pubhshed description. However, be certain to record any variations from the published procedure and to specify the apparatus that was used (make and model for commercial equipment, otherwise a sketch). If various pieces of equipment have identification numbers or serial numbers, these should be recorded. Note also any date of modification for apparatus. Include any calibration constants or calibration curves that are provided. For each chemical substance used, record the name, formula, source, grade or stated purity, and concentration (in case of a solution). If you have developed a checklist or work plan for the experiment, record this in your notebook also. 

Purchaser identification Most jurisdictions mandate that individual purchasers identify themselves with a photograph, proof of street or residential mailing address, and signature. Some Jurisdictions ask for the purchaser s birth date, driver s license or other state-issued identification number, year in which the purchaser s vehicle was manufactured, and vehicle license tag number. Most business recipients must furnish an authorization letter listing an identification number, an address, a phone number, and a description of the chemical s intended use. 

AEG Reports. These reports are received by OTS on automatic distribution, and since 1950 OTS has been the chief sales outlet for unclassified AEG reports. AEG reports are identified by their original AEG series numbers and are not assigned new identification numbers by OTS. All AEG reports supplied to OTS, including those available in photostat or microfilm are listed in USGRR. (For further information on AEG reports see the description of Atomic Energy Gommission.)... 

Finally, the Super Docket amendments authorized the use of United Nation s shipping descriptions and identification numbers for certain hazardous... 

Marking, as that term is used in the DOT hazard information scheme, refers to the application of the descriptive name, instructions, cautions, weight, identification numbers, or specification marks, or any combination thereof, on the outside containers of hazeirdous materials. The purpose of these requirements is to commimicate specific (and, with certain materials, rather extensive) in-... 

Soil can accumulate radionuclides over long time periods but may not be useful for observing short-term trends. Measurements can provide retrospective information on radionuclide levels. Site description, location, collection date and time, sample area and depth, and sampling method (core, template, trench) should be recorded along with the sample identification number and name of sample collector. 

Labeling a descriptive name, identification number, instructions, cautions, etc. to be placed directly on the primary container of hazardous materials. 

To make the necessary measurements, vertical parallel lines are drawn on the tracing connecting the two marks at each subdivision the height of the schlieren curve at each subdivision is measured with a machine divider ruler (Paragon 56 3278, Keuffel Esser Co., Hoboken, New Jersey), and transcribed onto a prepared data form. The form also contains spaces for such data as identification number, run type, Spinco E machine used, frames read, dilution from the original sample, location of the major component, density and temperature of the run, constants that require redefinition for the analysis of the run, and a brief descriptive statement that can serve to further identify the run. Most of this information can be optionally left blank if it is not applicable, and the program will automatically substitute the standard values or options. 

Description of each item, including number of containers, identification number(s), and a physical description... 

Failure to include an identification number in the shipping description 172.202 ... 

Biennial reports must be prepared by each generator initiating shipments of hazardous waste away fiom the facrlily. These must be prepared on EPA Form 8700-13A, submitted by March 1 of each even-numbered year, and must cover the previous calendar year. The report must provide (a) the EPA identification number, name and address of each facility to which waste was shipped during the year, (b) the name and EPA identification number of each transporter used during the year, and (c) a description, EPA identification waste number and amount of each hazardous waste shipped off-site. This information must be identified further with the identification number for each site to which it was shipped. The report must be signed by the generator or an authorized representative to certify that the report is correct. 

Identification Number Function Description Relay Type... 

Item 9. U.S. DOT Description (Including Proper Shipping Name, Hazard Class or Division, Identification Number, and Packing Group)... 

A snapshot is a condensed view of the companys profile as maintained by the Motor Carrier Management Information System (MCMIS). It includes information on the company s location, identification numbers, type, cargo carried or shipped, inspection summary, crash summary, and safety rating. Descriptions of individual data items are listed below. 

General Description Headlamp Concealment Devices Hood Latch Systems Theft Protection Vehicle Identification Numbers Windshield Mounting Motor Vehicle Brake Fluids Child Seating Systems Power-Operated Window Systems Side Door Strength Flammability of Interior Materials Air Brake Systems Exterior Protection (Bumpers) Retreaded Pneumatic Tires Roof Crush Resistance Motorcycle Brake Systems Warning Devices. 

---