Hydraulic similarity

Process design Fluid mechanics of impellers Fluid regime required by process Scaleup hydraulic similarity Impeller power characteristics... 

The principle of operation of the hydraulic reciprocating pump is similar to the beam pump, with a piston-like sub-surface pump action. The energy to drive the pump, however, is delivered through a hydraulic medium, the power fluid, commonly oil or water. The power fluid drives a downhole hydraulic motor which in turn drives the pump. A separate surface pump delivers the hydraulic power. The power fluid system can be of the closed loop or of the open type. In the latter case, the power fluids are mixed with the produced fluid stream. The performance of the hydraulic pump is primarily monitored by measuring the discharge pressures of both surface and sub-surface pumps. 

The jet pump relies on the same hydraulic power being delivered sub-surface as to the hydraulic reciprocating pump, but there the similarity ends. The high-pressure power fluid is accelerated through a nozzle, after whioh it is mixed with the well stream. The velocity of the well stream is thereby increased and this acquired kinetic energy is converted to pressure in an expander. The pressure is then sufficient to deliver the fluids to surface. The jet pump has no moving parts and can be made very compact. 

Metal- Working and Hydraulic Fluids. In the preparation of fluids for metal-working and hydrauflcs, the trend has been to replace organic-based materials with aqueous-based materials. Neodecanoic acid has found apphcation in these newer fluids as a corrosion inhibitor and a viscosity improver. For example, neodecanoic acid is used in an aqueous hydrauflc fluid concentrate for corrosion inhibition and improved antiwear properties (101), in the preparation of a thickened aqueous hydrauflc fluid to reduce viscosity loss (102), and in a water-soluble metal working oil to reduce corrosion (103). In a similar vein, neodecanoic acid has been used in antifreeze concentrates for corrosion inhibition (104). 

When the bulk containing the binder is uniform, it is compressed on pneumatic, hydraulic, or ram-type presses. Compression can be carried out in presses provided with suitably designed cavities or in metallic pans. The pans ate filled with the powder mass, and a plunger with a cross-sectional shape similar to that of the pan is used to compress the tablet. The resulting tablets ate commonly used with powder puffs or cosmetic bmshes. 

Hydraulic The design of typical hvdraiilic actuators is similar to double-acting piston pneumatic types. One kev advantage is the high pressure (yvpicallv35 to 70 bar [500 to 1000 psi]), vvFich leads to high thrust in a smaller paclcage. The incompressible nature of the... 

As most throttling control valves are still operated bv pneumatic actuators, the control-valve device descriptions that follow relate primarily to devices that are used with pneumatic actuators. The function of hydraulic and electrical coimteiparts are very similar. Specific details on a particular valve-control device are available from the vendor of the device. 

A duplex outside-end-packed plunger pump with pot valves, of the type used with hydraulic presses and for similar service, is shown in Fig. 10-49. In this drawing, plunger A is direct-connec ted to rod B, while plunger C is operated from the rod by means of yoke D and tie rods. 

According to the Standards of the Hydraulic Institute, a suction lift test is performed on the pump and the pressure in the suction vessel is lowered to the point where the pump suffers a 3% loss in total head. This point is called the NPSHr of the pump. Some pump manufacturers perform a similar test by closing a suction valve on a test pump and other manufacturers lower the suction elevation. 

Similarly, the pressure drop across the bit to produce the above hydraulic horsepower at a circulation flowrate of 300 gal/min is... 

To monitor the motors performance, a plot can be made in real time of the mechanical horsepower versus the hydraulic horsepower. The curve should be similar to the MHP curve of Figure 4-315 since, according to equation 4-233, at constant Q, the hydraulic power is proportional to AP, An example is shown in Figure 4-317 where measurements have been made at various RPM. 

These are not normally required. Where wet gas is supplied, it will be necessary to fit a vessel at low points in the installation to collect any condensate or fluid. This vessel shall be in a readily accessible position and a valve, suitably plugged or capped, shall be fitted to its drain connection. In the exceptional case where hydraulic pressure testing is to be carried out, similar provisions must be made. 

A similar action takes place in a fluid power system in which the fluid takes the place of the projectile. For example, the pump in a hydraulic system imparts energy to the fluid, which overcomes the inertia of the fluid at rest and causes it to flow through the lines. The fluid flows against some type of actuator that is at rest. The fluid tends to continue flowing, overcomes the inertia of the actuator, and moves the actuator to do work. Friction uses up a portion of the energy as the fluid flows through the lines and components. 

Directional control valves for hydraulic and pneumatic systems are similar in design and operation. However, there is one major difference. The return port of a hydraulic valve is ported through a return line to the reservoir. Any other differences are pointed out in the discussion of these valves. 

The bubble dynamics under conditions corresponding to flow in two parallel trapezoidal micro-channels with hydraulic diameter 47.7 pm was studied by Li et al. (2004). The bubbles in two parallel micro-channels generally grow similarly to that in a single micro-channel. The authors reported on the presence of two-phase flow... 

The electrical supply and the control lines for the hydraulic power unit are similarly prepared with Prohbus connection terminals. 

Bavarian and Fan [3, 4] reported a similar phenomenon occurring in a three-phase fluidized bed. In their case, the hydraulic transport of a packed bed occurred at the start-up of a gas-liquid-solid fluidized bed. Although the cause was different from the case reported in the present study, similar phenomena were observed in both cases. 

In equation (2) Rq is the equivalent capillary radius calculated from the bed hydraulic radius (l7), Rp is the particle radius, and the exponential, fxinction contains, in addition the Boltzman constant and temperature, the total energy of interaction between the particle and capillary wall force fields. The particle streamline velocity Vp(r) contains a correction for the wall effect (l8). A similar expression for results with the exception that for the marker the van der Waals attraction and Born repulsion terms as well as the wall effect are considered to be negligible (3 ). 

The mechanism by which sulphur has these observed effects is as follows. Immersion of native magnesium oxychloride cement in water brings about a slow dissolution which creates pores. When those pores are filled with sulphur, sites of possible stress concentration at points of contact between particles are modified. Similar effects occur when sulphur is used to impregnate hydraulic cements based on Portland cement and silica (Beaudoin, Ramachandran Feldman, 1977). 

GPl7][R21] Thepressuredropinafilamentous-bedreactor(i.d. 7 pm porosity 0.8),whichwasusedforpropanedehydrogenation,wascomparedwitharandomly packed powder bed (sphere diameter from 100 to 160 pm) of similar hydraulic... 

---