Viscosity reduced

The reduced viscosity (I/C2) (77/770 - 1). This is obtained by dividing both sides of Eq. (9.13) by C2 in this sense it is analogous to the reduced osmotic pressure ... 

The reduced viscosity expresses the specific viscosity per unit of solute concentration. 

Reduced viscosity Reducing bleaches Reducing sugars Reduction... 

The major use of vinylpyrrohdinone is as a monomer in manufacture of poly(vinylpyrrohdinone) (PVP) homopolymer and in various copolymers, where it frequendy imparts hydrophilic properties. When PVP was first produced, its principal use was as a blood plasma substitute and extender, a use no longer sanctioned. These polymers are used in pharmaceutical and cosmetic appHcations, soft contact lenses, and viscosity index improvers. The monomer serves as a component in radiation-cured polymer compositions, serving as a reactive diluent that reduces viscosity and increases cross-linking rates (see... 

Phosphoms-containing additives can act in some cases by catalyzing thermal breakdown of the polymer melt, reducing viscosity and favoring the flow or drip of molten polymer from the combustion zone (25). On the other hand, red phosphoms [7723-14-0] has been shown to retard the nonoxidative pyrolysis of polyethylene (a radical scission). For that reason, the scavenging of radicals in the condensed phase has been proposed as one of several modes of action of red phosphoms (26). 

These polymers have reduced viscosities up to 1.13 dL/g and electric conductivity as high as 10 10 S/cm. Ah. the polymers are insoluble in... 

Solutions of welan are very viscous and pseudoplastic, ie, shear results in a dramatic reduction in viscosity that immediately returns when shearing is stopped, even at low polymer concentrations (230). They maintain viscosity at elevated temperatures better than xanthan gum at 135°C the viscosity half-life of a 0.4% xanthan gum solution is essentially zero, whereas a welan gum solution has a viscosity half-life of 900 minutes (230). The addition of salt to welan solutions slightly reduces viscosity, but not significantly. It has excellent stabiUty and theological properties in seawater, brine, or 3% KCl solutions... 

High temperature steam (qv) is also used for recovery of viscous cmde oils (28). Heat from the steam thins the oil, reducing viscosity and increasing mobihty. The mobilized oil is produced at offset production wells. In heavy oil fields, water flooding is often omitted and steam injection begun immediately after primary production. Steam injection temperature is typically 175—230°C in California oil fields. Injection temperature can reach 300°C in Canadian and Venezuelan EOR projects. 

Eig. 2. Effect of stoichiometric imbalance in polysulfone polymerization on maximum attainable polymer reduced viscosity where (x) is theoretical,... 

Dilute Polymer Solutions. The measurement of dilute solution viscosities of polymers is widely used for polymer characterization. Very low concentrations reduce intermolecular interactions and allow measurement of polymer—solvent interactions. These measurements ate usually made in capillary viscometers, some of which have provisions for direct dilution of the polymer solution. The key viscosity parameter for polymer characterization is the limiting viscosity number or intrinsic viscosity, [Tj]. It is calculated by extrapolation of the viscosity number (reduced viscosity) or the logarithmic viscosity number (inherent viscosity) to zero concentration. 

ThermalLkjucfaction Process. In the thermal Hquefaction process (see Eig. 1), a starch slurry containing no enzyme or added calcium is heated for several minutes. The slurry is slightly acidic and sufficient acid Hquefaction is achieved to reduce viscosity. The hydrolyzate (at essentially zero DE) is flash-cooled to 95—100°C, a-amylase is added, and the pH is adjusted. The reaction then goes to completion. 

Curves for the viscosity data, when displayed as a function of shear rate with temperature, show the same general shape with limiting viscosities at low shear rates and limiting slopes at high shear rates. These curves can be combined in a single master curve (for each asphalt) employing vertical and horizontal shift factors (77—79). Such data relate reduced viscosity (from the vertical shift) and reduced shear rate (from the horizontal shift). 

Metal- Working and Hydraulic Fluids. In the preparation of fluids for metal-working and hydrauflcs, the trend has been to replace organic-based materials with aqueous-based materials. Neodecanoic acid has found apphcation in these newer fluids as a corrosion inhibitor and a viscosity improver. For example, neodecanoic acid is used in an aqueous hydrauflc fluid concentrate for corrosion inhibition and improved antiwear properties (101), in the preparation of a thickened aqueous hydrauflc fluid to reduce viscosity loss (102), and in a water-soluble metal working oil to reduce corrosion (103). In a similar vein, neodecanoic acid has been used in antifreeze concentrates for corrosion inhibition (104). 

In the alcohol industry, grain or potato raw materials are milled and water added to form a slurry or mash which is heated either batchwise or continuously. Traditionally, the mash is heated to 150°C by the injection of Uve steam. To reduce viscosity, a-amylases are added both during beating to 150°C and during cooling. Thermostable a-amylases from Bacillus licheniformis are the most commonly used enzymes for these processes (68). 

The epoxidation is generally conducted in two steps (/) the polyol is added to epichlorohydrin in the presence of a Lewis acid catalyst (stannic chloride, boron triduoride) to produce the chlorohydrin intermediate, and (2) the intermediate is dehydrohalogenated with sodium hydroxide to yield the aliphatic glycidyl ether. A prominent side-reaction is the conversion of aliphatic hydroxyl groups (formed by the initial reaction) into chloromethyl groups by epichlorohydrin. The aliphatic glycidyl ether resins are used as flexibilizers for aromatic resins and as reactive diluents to reduce viscosities in resin systems. 

Monofunctional aliphatic glycidyl ethers, eg, based on / -butanol or mixed Cg—alcohols, are used exclusively as reactive diluents to reduce viscosities of epoxy resin systems. Some loss of desirable cured properties results from the lowered functionality of the systems. 

---