Plunger pump

The convenience of the offered monitoring system consists in an opportunity fast adjustment in conditions of many nomenclature manufacture, reception of the protocol of the testing results, opportunity of use of the unskilled personnel. By an offered principle installations for the testing of welding by explosion of cases of plunger pumps, details of air engineering and other were developed. 

Reciprocating Pumps There are three classes of reciprocating pumps piston pumps, plunger pumps, and diaphragm pumps. 

A duplex outside-end-packed plunger pump with pot valves, of the type used with hydraulic presses and for similar service, is shown in Fig. 10-49. In this drawing, plunger A is direct-connec ted to rod B, while plunger C is operated from the rod by means of yoke D and tie rods. 

Plunger pumps are available with one, two, three, four, five, or even more cylinders. Simplex and duplex units are often built in a horizontal design. Those with three or more cylinders are usually of vertical... 

The flow required to lubricate the packing and cylinders is quite small, and the pressure necessary to inject the lubricant at these locations is quite high. Therefore, small plunger pump (force-feed lubricators) sys-... 

Figure 3-67. Duplex double-acting plunger pump, power driven. (Courtesy Worthington Corp.)...

The piston plunger pump is the simplest form of a positive displacement pump. These pumps can be powered by a variety of prime movers, internal combustion engines, and electric motors (and in some cases, powered by a gas turbine motor). In such applications, the separate pump unit is connected to the prime mover by a power transmission. 

The hydraulic press, invented by an Englishman, John Brahmah, was one of the first workable machines that used hydraulics in its operation. It consisted of a plunger pump piped to a large cylinder and a ram. This press found wide use in England because it provided a more effective and economical means of applying large, uniform forces in industrial uses. 

Figure A8.14 Closed column reactor for the production of L-alanine. 1) reactor 2) plunger pump 3) pressure control valve 4) reservoir 5) substrate tank 6) pressure gauge 7) safety valve 8) heat exchanger.

Concentrate recycle RO plants allow some of the brine reject water to recycle back through the plant, which improves the permeate recovery rate. (The reduced flow of brine reject water does of course have a proportionally higher TDS level.) Various types of high pressure, corrosion-resistant pumps are used, including multistage, centrifugal and plunger pumps, each with their own benefits and area of application. 

Pumps which operate with periodically increasing and deaeasing pump cham-ber volumes (rotary vane and rotary plunger pumps also trochoid pumps)... 

Shown in Fig. 2.9 is a sectional view of a rotary plunger pump of the single block type. Here a piston (2) which is moved along by an eccentric (3) turning in the direction of the arrow moves along the chamber wall. The gas which is to be pumped flows into the pump through the intake port (11), passes... 

The motors supplied with the rotary vane and rotary plunger pumps deliver enough power at ambient temperatures of 12 °C and when using our special oils to cover the maximum power requirement (at about 400 mbar). Within the actual operating range of the pump, the drive system of the warmed up pump needs to supply only about one third of the Installed motor power (see Fig. 2.11). 

Ethanoic acid is to be pumped with a rotary plunger pump. 

E 250 (single-stage rotary plunger pump, operated without gas ballast). In... 

Region A Single-stage, rotary plunger pumps without gas ballast inlet. 

This requirement is valid in the whole working region of the single-stage rotary plunger pump - hence, at total pressures between 10 and 1013 mbar. 

Region B Single-stage rotary plunger pumps with gas ballast and an inlet condenser. 

As there is merely a compression between the Roots pump and the rotary plunger pump, the following applies here too ... 

---