Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

High electrical resistance

It is a white crystalline, brittle metal with a pinkish tinge. It occurs native. Bismuth is the most diamagnetic of all metals, and the thermal conductivity is lower than any metal, except mercury. It has a high electrical resistance, and has the highest Hall effect of any metal (i.e., greatest increase in electrical resistance when placed in a magnetic field). [Pg.146]

Spinel ferrites, isostmctural with the mineral spinel [1302-67-6] MgAl204, combine interesting soft magnetic properties with a relatively high electrical resistivity. The latter permits low eddy current losses in a-c appHcations, and based on this feature spinel ferrites have largely replaced the iron-based core materials in the r-f range. The main representatives are MnZn-ferrites (frequencies up to about 1 MH2) and NiZn-ferrites (frequencies 1 MHz). [Pg.187]

Electrical. Glasses are used in the electrical and electronic industries as insulators, lamp envelopes, cathode ray tubes, and encapsulators and protectors for microcircuit components, etc. Besides their abiUty to seal to metals and other glasses and to hold a vacuum and resist chemical attack, their electrical properties can be tailored to meet a wide range of needs. Generally, a glass has a high electrical resistivity, a high resistance to dielectric breakdown, and a low power factor and dielectric loss. [Pg.299]

Sheet Miea. Good quahty sheet mica is widely used for many iadustrial appHcations, particularly ia the electrical and electronic iadustries, because of its high dielectric strength, uniform dielectric constant, low power loss (high power factor), high electrical resistivity, and low temperature coefficient (Table 6). Mica also resists temperatures of 600—900°C, and can be easily machined iato strong parts of different si2es and shapes (1). [Pg.291]

Electrical Properties. Nylon has low electrical conductivity (high electrical resistivity) and behaves like an insulator. Nylon-6 has a resistivity of 6 X lO " Hem when dry and a resistivity of 2 x lO " Hem when conditioned at 100% rh at 20°C (44) nylon-6,6 responds similarly. [Pg.249]

The properties of high quaUty vitreous sihca that determine its uses iaclude high chemical resistance, low coefficient of thermal expansion (5.5 X 10 /° C), high thermal shock resistance, high electrical resistivity, and high optical transmission, especially ia the ultraviolet. Bulk vitreous sihca is difficult to work because of the absence of network-modifyiag ions present ia common glass formulations. An extensive review of the properties and stmcture of vitreous sihca is available (72). [Pg.476]

The high electrical resistivity of asbestos fibers is weU-known, and has been widely exploited in electrical insulation appHcations. In general, the resistivity of chrysotile is lower than that of the amphiboles, particularly in high humidity environments (because of the availabiHty of soluble ions). For example, the electrical resistivity of chrysotile decreases from 1 to 2100 MQ/cm in a dry environment to values of 0.01 to 0.4 MQ/cm at 91% relative humidity. Amphiboles, on the other hand, exhibit resistivity between 8,000 and 900,000 MQ/cm. [Pg.351]

The aperture impedance principle of blood cell counting and sizing, also called the Coulter principle (5), exploits the high electrical resistivity of blood cell membranes. Red blood cells, white blood cells, and blood platelets can all be counted. In the aperture impedance method, blood cells are first diluted and suspended ia an electrolytic medium, then drawn through a narrow orifice (aperture) separating two electrodes (Fig. 1). In the simplest form of the method, a d-c current flows between the electrodes, which are held at different electrical potentials. The resistive cells reduce the current as the cells pass through the aperture, and the current drop is sensed as a change in the aperture resistance. [Pg.401]

BeryUia ceramics offer the advantages of a unique combination of high thermal conductivity and heat capacity with high electrical resistivity (9). Thermal conductivity equals that of most metals at room temperature, beryUia has a thermal conductivity above that of pure aluminum and 75% that of copper. Properties Ulustrating the utUity of beryUia ceramics are shown in Table 2. [Pg.76]

Other sohd-state apphcations of sihcon carbide include its use as an electroluminescent diode for use in sound recording equipment and photomultipliers and controllers. It has been studied as a reflective surface for lasers. By combining its excellent thermal conductivity and high electrical resistance, sihcon carbide has also found apphcation as an insulating material for integrated circuit substrates. [Pg.468]

Thermal Conductivity. The value of 2000 W/(m-K) at room temperature for Type Ila natural stones is about five times that of Cu, and recent data on 99.9% isotopicaHy pure Type Ila synthesized crystals ate in the range of 3300—3500 W/(m-K) (35). This property combined with the high electrical resistance makes diamond an attractive material for heat sinks for electronic devices. [Pg.559]

The high electrical resistivity and the magnitude of the optical bandgap of Cfio can be reduced by the application of high pressure, with decreases in resistivity of about one order of magnitude observed per 10 GPa pressure [117]. However, at a pressure of 20 GPa, an irreversible phase transition to a more insulating phase has been reported [117]. [Pg.59]

The performance of the unit involves the gas characteristics, analysis, velocity, flow rate, dust or liquid particle size and analysis, resistixdty and required final particle efficiency of removal. Some particle materials of high electrical resistivity prevent proper electrical operation. [Pg.284]

Light, sandy, well-drained soil of high electrical resistivity is low in corrosivity and coated steel or bare stainless steels can be employed. It is unlikely that the whole pipe run would be in the same type of soil. In heavier or damp soils, or where the quality of back filling cannot be guaranteed, there are two major corrosion risks. Steel, copper alloys and most stainless steels are susceptible to sulfide attack brought about by the action of sulfate-reducing bacteria in the soil. SRB are ubiquitous but thrive particularly well in the anaerobic conditions which persist in compacted soil, especially clay. The mechanism of corrosion where SRB are involved is described in Section... [Pg.903]

Contact with steel, though less harmful, may accelerate attack on aluminium, but in some natural waters and other special cases aluminium can be protected at the expense of ferrous materials. Stainless steels may increase attack on aluminium, notably in sea-water or marine atmospheres, but the high electrical resistance of the two surface oxide films minimises bimetallic effects in less aggressive environments. Titanium appears to behave in a similar manner to steel. Aluminium-zinc alloys are used as sacrificial anodes for steel structures, usually with trace additions of tin, indium or mercury to enhance dissolution characteristics and render the operating potential more electronegative. [Pg.662]

It is a valve metal and when made anodic in a chloride-containing solution it forms an anodic oxide film of TiOj (rutile form), that thickens with an increase in voltage up to 8-12 V, when localised film breakdown occurs with subsequent pitting. The TiOj film has a high electrical resistivity, and this coupled with the fact that breakdown can occur at the e.m.f. s produced by the transformer rectifiers used in cathodic protection makes it unsuitable for use as an anode material. Nevertheless, it forms a most valuable substrate for platinum, which may be applied to titanium in the form of a thin coating. The composite anode is characterised by the fact that the titanium exposed at discontinuities is protected by the anodically formed dielectric Ti02 film. Platinised titanium therefore provides an economical method of utilising the inertness and electronic conductivity of platinum on a relatively inexpensive, yet inert substrate. [Pg.165]

Paints used for protecting the bottoms of ships encounter conditions not met by structural steelwork. The corrosion of steel immersed in sea-water with an ample supply of dissolved oxygen proceeds by an electrochemical mechanism whereby excess hydroxyl ions are formed at the cathodic areas. Consequently, paints for use on steel immersed in sea-water (pH 8-0-8-2) must resist alkaline conditions, i.e. media such as linseed oil which are readily saponified must not be used. In addition, the paint films should have a high electrical resistance to impede the flow of corrosion currents between the metal and the water. Paints used on structural steelwork ashore do not meet these requirements. It should be particularly noted that the well-known structural steel priming paint, i.e. red lead in linseed oil, is not suitable for use on ships bottoms. Conventional protective paints are based on phenolic media, pitches and bitumens, but in recent years high performance paints based on the newer types of non-saponifiable resins such as epoxies. [Pg.648]

High electrical resistance. The coating must be an electrical insulator and must not contain any conducting material. [Pg.659]

The extent of galvanic action in atmospheric exposure may also be restricted by the development of corrosion products of high electrical resistance between the contacting surfaces — this is especially likely to occur if one of the metals in the couple is an iron or steel that will rust. In long-time tests such possible interruptions in the galvanic circuit should be checked by resistance measurements from time to time so as to determine the actual periods in which galvanic effects could operate. [Pg.1071]

We did not feel any of these methods would work reliably on a commercial scale at current densities in the range of 300 mA cm"2 or for commercial periods (at least 4000 hr). Rudge s work9,10 with porous carbon anodes was a very elegant solution to the problem (and formed the basis for the Phillips Electrochemical Fluorination process), but the high electrical resistance of the porous carbon limited it to small anodes at high current densities or lower current densities on large anodes. [Pg.530]


See other pages where High electrical resistance is mentioned: [Pg.449]    [Pg.187]    [Pg.188]    [Pg.190]    [Pg.138]    [Pg.342]    [Pg.57]    [Pg.447]    [Pg.533]    [Pg.72]    [Pg.400]    [Pg.359]    [Pg.363]    [Pg.261]    [Pg.486]    [Pg.145]    [Pg.2030]    [Pg.210]    [Pg.377]    [Pg.468]    [Pg.155]    [Pg.552]    [Pg.503]    [Pg.307]    [Pg.690]    [Pg.1070]    [Pg.256]    [Pg.280]    [Pg.295]    [Pg.368]   


SEARCH



Electric resistance

Electric resistivity

Electrical resistance/resistivity

Electrical resistivity

Electricity resistance

© 2024 chempedia.info