Sacrificial anode, 2.22

The coating has an that is negative to the material to be protected and the layer serves as a sacrificial anode. 

Galvanic corrosion can be controlled by the use of sacrificial anodes. This is a common method of controlling corrosion in heat exchangers with Admiralty tube bundles and carbon steel tube sheets and channel heads. The anodes are bolted direcdy to the steel and protect a limited area around the anode. Proper placement of sacrificial anodes is a precise science. 

The most significant chemical property of zinc is its high reduction potential. Zinc, which is above iron in the electromotive series, displaces iron ions from solution and prevents dissolution of the iron. For this reason, zinc is used extensively in coating steel, eg, by galvanizing and in zinc dust paints, and as a sacrificial anode in protecting pipelines, ship hulls, etc. 

Two methods of providing cathodic protection for minimizing corrosion of metals are in use today. These are the sacrificial-anode method and the impressed-emf method. Both depend upon making the metal to be protected the cathode in the electrolyte involved. 

Examples of the sacrificial-anode method include the use of zinc, magnesium, or aluminum as anodes in electrical contact with the metal to be protected. These may be anodes buried in the ground for protection of underground pipe lines or attachments to the surfaces of equipment such as condenser water boxes or on ship hulls. The current required is generated in this method by corrosion of the sacrificial-anode material. In the case of the impressed emf, the direct current is provided by external sources and is passed through the system by use of essentially nonsacrificial anodes such as carbon, noncor-rodible alloys, or platinum buried in the ground or suspended in the electrolyte in the case of aqueous systems. 

Cathodic protection using sacrificial anodes or applied current can retard or eliminate tuberculation. However, costs can be high and technical installation can be very difficult. Costs are markedly reduced if surfaces are coated (see Material substitution below). 

Applied current devices as well as sacrificial anodes have frequently been used to decrease corrosion associated with deposition. The effec-... 

Cathodic protection (involving the use of applied current or sacrificial anodes)... 

Note that zinc anodes are often used to protect steel and other relatively noble metals cathodically. In this case, the fasteners were acting as unintentional sacrificial anodes, protecting the stainless steel. Simple solutions to the problem would be to insulate the fasteners from the stainless steel electrically or to use stainless steel fasteners. 

Naturally, because the protection depends on the dissolution of the anodes, these require replacement from time to time (hence the term sacrificial anodes). In order to minimise the loss of anode metal, it is important to have as good a barrier layer around the pipe as possible, even though the pipe would still be protected with no barrier layer at all. 

With metals other than Fe, the percent of the ac current leading to corrosion can be considerably different. Cu and Pb behave similarly to Fe [36], whereas A1 [36] and Mg [39] corrode much more severely. This has to be watched with sacrificial anodes of these materials if they are subjected to ac. 

Anax maximum current density of a sacrificial anode A m, mA cm" ... 

Q current constant of sacrificial anodes per unit mass A h kg ... 

CoiTosion prevention is achieved by correct choice of material of construction, by physical means (e.g. paints or metallic, porcelain, plastic or enamel linings or coatings) or by chemical means (e.g. alloying or coating). Some metals, e.g. aluminium, are rendered passive by the formation of an inert protective film. Alternatively a metal to be protected may be linked electrically to a more easily corroded metal, e.g. magnesium, to serve as a sacrificial anode. 

Sacrificial anode system (reactive metal anode)... 

Sacrificial anode systems operate without external power source. The anodes are reactive metals such as magnesium and zinc or aluminum alloys. The energy for the process is derived from the anode material. Careful design is required to match the output and lifetime of the anodes with the polarization and life-expectancy requirements of the plant. Sacrificial anode CP is used for offshore platforms, sub-sea pipelines and the inside of ballast tanks on tanker ships. 

As is well known, high-purity zinc corrodes much less rapidly in dilute acids than commercial purity material in the latter instance, impurities (particularly copper and iron) are exposed on the surface of the zinc to give local cathodes with low hydrogen overpotentials this result is of practical significance only in the use of zinc for sacrificial anodes in cathodic protection or for anodes in dry cells. In neutral environments, where the cathodic... 

This is utilised in the cathodic protection of metals using sacrificial anodes (see Section 10.2). 

Cathodic protection with a sacrificial anode that is less noble than either member of the couple is frequently used to reduce the severity of bimetallic corrosion, particularly that resulting from the use of bronze propellers in steel ship hulls. 

Contact with steel, though less harmful, may accelerate attack on aluminium, but in some natural waters and other special cases aluminium can be protected at the expense of ferrous materials. Stainless steels may increase attack on aluminium, notably in sea-water or marine atmospheres, but the high electrical resistance of the two surface oxide films minimises bimetallic effects in less aggressive environments. Titanium appears to behave in a similar manner to steel. Aluminium-zinc alloys are used as sacrificial anodes for steel structures, usually with trace additions of tin, indium or mercury to enhance dissolution characteristics and render the operating potential more electronegative. 

---