Environmental conditions, control

Accidents are mainly caused by the unsafe acts of people and people can create and improve environmental conditions. Controlling of human behavior could control most of the accidents, zero accidents can be achieved. 

Unlike catfish, tilapia, trout and salmon, that produce several hundred to several thousand eggs per female, many marine species produce large numbers of very small eggs. Hundreds of thousands to millions of eggs are produced by such species as haUbut, flounders, red dmm, striped bass, and shrimp. Catfish, salmon, and trout spawn once a year, while tilapia and some marine species spawn repeatedly if the proper environmental conditions are maintained (1). Red dmm, for example, spawn every few days for periods of several months when light and temperature and properly controlled (10). 

Advanced composites and fiber-reinforced materials are used in sailcloth, speedboat, and other types of boat components, and leisure and commercial fishing gear. A ram id and polyethylene fibers are currentiy used in conveyer belts to collect valuable offshore minerals such as cobalt, uranium, and manganese. Constmction of oil-adsorbing fences made of high performance fabrics is being evaluated in Japan as well as the constmction of other pollution control textile materials for maritime use. For most marine uses, the textile materials must be resistant to biodeterioration and to a variety of aqueous pollutants and environmental conditions. 

In contrast, various sensors are expected to respond in a predictable and controlled manner to such diverse parameters as temperature, pressure, velocity or acceleration of an object, intensity or wavelength of light or sound, rate of flow, density, viscosity, elasticity, and, perhaps most problematic, the concentration of any of millions of different chemical species. Furthermore, a sensor that responds selectively to only a single one of these parameters is often the goal, but the first attempt typically produces a device that responds to several of the other parameters as well. Interferences are the bane of sensors, which are often expected to function under, and be immune to, extremely difficult environmental conditions. 

To remain safe and efficacious on the eye, contact lenses must maintain clear and wetted surfaces, provide an adequate supply of atmospheric oxygen to and adequate expulsion of carbon dioxide from the cornea, allow adequate flow of the eye s tear fluid, and avoid excessive abrasion of the ocular surface or eyeflds, all under a variety of environmental conditions. The clinical performance of a contact lens is controlled by the nature of the lens material the lens design the method and quaUty of manufacture the lens parameters or specifications prescribed by the practitioner and the cleaning, disinfection, and wearing procedures used by the patient. 

In the field of toner materials, the emphasis in the 1990s is on increasing developer life, particularly using color toners. The life of a typical black two-component developer is about 80—100 kilocycles per kilogram, whereas for color toners it is only about 10 kilocycles per kilogram (64). Also, there is a need for better control of triboelectrification of toner particles that would not only allow stable operation under all environmental conditions but also provide consistent, fast, and reproducible contact charging. 

Television with automatic color, brightness, and acoustic control based on signal and environmental conditions... 

Pesticides vary widely in their chemical and physical characteristics and it is their solubility, mobility and rate of degradation which govern their potential to contaminate Controlled Waters. This, however, is not easy to predict under differing environmental conditions. Many modern pesticides are known to break down quickly in sunlight or in soil, but are more likely to persist if they reach groundwater because of reduced microbial activity, absence of light, and lower temperatures in the sub-surface zone. 

ISA S71.04. 1986. Environmental Conditions for Process Measurement and Control Systems Airborne Contaminants. Instrument Society of America, Research Triangle Park, N.C. 

The losses that are encountered in a plant can be divided into two groups, uncontrollable losses, and controllable losses. The uncontrollable losses are usually environmental conditions, such as temperature, pressure, humidity, and the turbine aging. Table 20-3 shows the approximate changes that would occur for these changes. It must be remembered that these are just approximations and will vary for individual power plants. 

Environmental conditions under which solvent release from the adhesive on the substrate is produced must be carefully controlled. Humidity is critical because loss of heat due to solvent evaporation may allow attainment of the dew point (the evaporation of the solvent is an endothermic process), and then condensation of water on the adhesive can result. This phenomenon is often called moisture blooming. The presence of water on the adhesive film causes a detrimental effect because the autoadhesion of rubber chains is greatly inhibited. Therefore, humidity must be controlled and avoided by increasing the temperature during solvent evaporation. 

In contrast, composting processes utilize a mixture of solids and yard waste under controlled environmental conditions to produce a disinfected, humus-like product. Three common composting systems are a horizontal agitated reactor, a horizontal nonagitated reactor, and an aerated static pile system (nonproprietary). Compost can be marketed as a soil conditioner in competition with such products as peat, soil, and mulch. Although a large potential market exists, significant effort is required to penetrate this market. Yard waste revenue of 6.50/m (S5/yd ) and product revenue of 2.00/m ( 1.50/yd ) appear to be reasonable market values based on various studies reported on the Web. 

A workbench makes use of a local air supply in conjunction with exhaust air to ensure good control of the contaminants generated on a bench process. The local exhaust removes the contaminants, while the local supply air protects the operator and/or the products against airborne contaminants. The local supply air improves the thermal environmental conditions by introducing cool dehumidified air in a hot environment. This ensures that the operator s thermal comfort is maintained in areas of high temperature, where full air conditioning of the entire workspace is nor economically feasible. 

Boundary conditions The actual environmental conditions within a controlled zone. 

Environmental Condition for Process Measurement and Control Systems Temperature and Humidity Electrical Instruments in Hazardous Locations, Ernest C. Magison, 1978... 

The likelihood (probability) of an accidental release based on tlie history of current conditions and controls at tlie facility, consideration of any unusual environmental conditions (e.g., areas in flood plains), or tlie possibility of simultaneous emergency incidents (e.g., flooding or fire liazards resulting in tlie release of hazardous materials). 

To maintain acceptable indoor air quality, the concentration of pollutants known to degrade indoor air quality and affect human health must be controlled. If the origin of the contaminant is known, it is more effective to exercise source control over any mitigation strategy. If the origin of the contaminants is not known, building ventilation and air cleaning and filtration are the two most commonly used processes to dilute or remove all types of contaminants from the indoor air and maintain acceptable indoor environmental conditions. 

Whilst careful design and informed forethought can often minimise or even prevent corrosion at little extra cost where the environmental conditions or the conditions of service are severe (as in most forms of marine and offshore engineering) reliable, secure and cost-effective corrosion control cannot be effectively achieved without considerable expense, although even in these circumstances good design can help to significantly reduce this. In... 

The controversy that arises owing to the uncertainty of the exact values of and b and their variation with environmental conditions, partial control of the anodic reaction by transport, etc. may be avoided by substituting an empirical constant for (b + b /b b ) in equation 19.1, which is evaluated by the conventional mass-loss method. This approach has been used by Makrides who monitors the polarisation resistance continuously, and then uses a single mass-loss determination at the end of the test to obtain the constant. Once the constant has been determined it can be used throughout the tests, providing that there is no significant change in the nature of the solution that would lead to markedly different values of the Tafel constants. 

---