Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Loss control

The samples were collected and processed in a manner to avoid exposure to oxygen and control loss of moisture then they were pulverized to convenient sizes for research, ie, <149 fim ( — 100 mesh) and <840 fim (—20 mesh) the entire ton was thoroughly mixed and packaged in sealed glass ampules under nitrogen. These samples have been well characterized and are available in quantities that are expected to last for decades (Table 8). [Pg.230]

The losses that are encountered in a plant can be divided into two groups, uncontrollable losses, and controllable losses. The uncontrollable losses are usually environmental conditions, such as temperature, pressure, humidity, and the turbine aging. Table 20-3 shows the approximate changes that would occur for these changes. It must be remembered that these are just approximations and will vary for individual power plants. [Pg.719]

The controllable losses are those that the operator can have some degree of control over and can take corrective actions ... [Pg.719]

Effect of Controllable Losses on the Output and Heat Rate... [Pg.720]

Loss of control also is typical among people who abuse drugs, and some drug users will describe their habits as being out of control. Loss of control has been described as an inability to predict when or how many drugs will be consumed. Some drug users describe loss of control as powerlessness, meaning that the desire for substances controls their behavior. [Pg.8]

Several factors influence TGA data. Sample size and shape affect the rate and efficiency of decomposition. Powdered versus solid bulk samples will have different decomposition profiles due to the differing surface areas from which exiting decomposition products can leave the sample and be registered as mass losses. Similarly, the packing of the sample in the pan must be even and reproducible from run to run. Loosely distributed particles will heat more evenly and evolve volatilized products more evenly than mounded or densely packed samples. This can be especially important when looking at determinations of residual solvents, moisture or diffusion controlled losses such as plasticizer in the samples. [Pg.117]

Materials. The materials are described in detail in the studies summarized in Table I. Most of these results are based on kraft lignin. The NCO/OH ratio of all of these networks were high greater than 1.5. All of the networks were prepared from homogeneous solutions of the lignin-based polyol, added (soft segment) polyol, and diisocyanate. Films were cast and cured under mild conditions with a controlled loss of solvent. The films were post-cured to insure complete reaction (25). [Pg.406]

Lead Determine as directed under Lead Limit Test, Appendix IIIB, using a Sample Solution prepared as directed for organic compounds, and 5 pg of lead (Pb) ion in the control. Loss on Drying Dry at 105° for 2 h. [Pg.13]

Lead Determine as directed under Lead Limit Test, Appendix IIIB, using a Sample Solution prepared as directed for organic compounds, and 5 p.g of lead (Pb) ion in the control. Loss on Drying Determine as directed under Loss on Drying, Appendix IIC, drying the sample at 105° for 3 h. Optical (Specific) Rotation Determine as directed under Optical (Specific) Rotation, Appendix IIB, using a solution containing 8 g of a previously dried sample in sufficient 6 N hydrochloric acid to make 100 mL. [Pg.35]


See other pages where Loss control is mentioned: [Pg.2861]    [Pg.251]    [Pg.706]    [Pg.720]    [Pg.59]    [Pg.107]    [Pg.176]    [Pg.804]    [Pg.349]    [Pg.642]    [Pg.207]    [Pg.166]    [Pg.359]    [Pg.18]    [Pg.26]    [Pg.28]    [Pg.131]    [Pg.188]    [Pg.193]   
See also in sourсe #XX -- [ Pg.5 , Pg.6 , Pg.8 , Pg.9 ]




SEARCH



© 2024 chempedia.info